Instruction/ maintenance manual of the product 55-1539A Stamina Products
Go to page of 19
55-1539A ST AMINA PRODUCTS MADE IN CHINA Product May V ary Slightly From Pictured. Owner's M a nual CAUTION: 1. Weight on this product should not exceed 300 lbs. 2. Cla ss H equipment: This equipment is f or home use only . It is not for commercial use.
T ABLE OF CONTENTS Page Page Safety In struction s 2 Before Y ou Begin 4 Equipment W arning & Notice Labels 5 Hardware Identification Chart 6 Asse mbly In structions 7 Operation al In struction s .
THAN K YOU FOR PURCHASING THE Thera py Inversion Syste m T o help you get started, we have pre-a sse mbled most of your Thera py Inversion Syste m at the f a ctory with the exce ption of those few parts left un a sse mbled for shi pping purpose s. Simply f ollow the few a ssembly in structions set f orth in this ma nual.
BEFORE YOU BEGIN 4 Footrest Right Pivot Arm Lever He ight Adjustment Be a m Foa m Pad Right Protective Cover Round Sta nd Buckle Stra p Bumper Heel Holder Nylon Bed Ha ndrail Re ar Fra me Locking Knob.
5 EQUIPMENT W AR NING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Thera py Inversion Syste m. Plea se ta ke a moment to fa miliarize yoursel f with all of the warning & notice labels.
6 Part No. and De scription Qty 43 Bolt, Hex He ad (M6 x 1 x 42mm) 1 44 Bolt, Hex He ad (M6 x 1 x 47mm) 1 45 Bolt, Hex He ad (M8 x 1.25 x 15mm) 2 46 Bolt, Hex He ad (M8 x 1.
ASSEMBL Y INSTRUCTIONS Pla ce all parts from the box in a cleared area a nd position them on the floor in front of you. Remove all pa cking materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als until a ssembly is completed.
STEP 4 Atta ch the FOOTREST(13) onto the HEIGHT ADJUSTMENT BEAM(12) with the ADJUSTMENT K NOB(24). NOTE: STEP 5 Insert the HEEL HOLDER TUBE(17) through the hole on the HEIGHT ADJUSTMENT BEAM(12) and secure with HEX BOL T(M6x1x47mm)(44), W ASHERS(M6)(50), a nd NYLOCK NUT(M6x1)(48).
ASSEMBL Y INSTRUCTIONS 1. 2. Buckle A. C. B. Buckle 9 STEP 7 Install the HEIGHT ADJUSTMENT BEAM(12) into MAIN FRAME(4) by pulling the SPRING PIN(22) on the MAIN FRAME(4) a nd inserting the HEIGHT ADJUSTMENT BEAM(12) a s shown. For a dded safety , threa d the SECURING K NOB(23) into the ba ck side of the MAIN FRAME(4).
STEP 10: Slide the LEFT a nd RIGHT PROTECTIVE COVERS(26, 27) onto ea ch side of the BASE ASSEMBL Y . Ma ke sure the SHAFTS on the FRONT FRAME(1) poke out through the hole on the PROTECTIVE COVERS(26, 27). NOTE: Do not secure the PROTECTIVE COVERS(26, 27) to the FOLDING LIN KAGES(3) with the SECURING STRAPS on the covers until STEP 12.
OPERA TIONAL INSTRUCTIONS GENERAL PRECAUTIONS Do not use the Thera py Inversion Syste m alone. Always have a helper availa ble in ca se a ssista nce is needed in recovering from the decline position. Ma ke sure that the FOAM P ADS(16) a nd HEEL HOLDERS(19) are holding your feet se curely .
OPERA TIONAL INSTRUCTIONS HEEL HOLDER USE AND ADJUSTMENT Start by lying fully ba ck on the bed with your ha nds at your side, or resting on your thighs. Keeping your ha nds close to your body begin to raise your arms slowly allowing the table to rotate ba ckward.
OPERA TIONAL INSTRUCTIONS 13 SUGGESTIONS FOR USE Begin slowly; invert only 15-20 degrees to begin with. Stay inverted only a s long a s you are comforta ble. Return upright slowly . Ma ke gradual cha nges: increa se the a ngle only if it is comf ortable.
PRODUCT P ARTS DR A WING BACK FRONT 14.
15 1 Front Fra me 1 2 Rear Fra me 1 3 Folding Linkage 2 4 Main Fra me 1 5 Left Pivot Arm 1 6 Right Pivot Arm 1 7 Linkage 2 8 Left Ha ndrail Support 1 9 Right Ha ndrail Support 1 10 Ha ndrail 2 1 1 Loc.
16 P ARTS LIST DIAGRAM# P ART NAME QTY 47 Bolt, Hex Hea d (M8 x 1.25 x 20mm) 2 48 Nylock Nut (M6 x 1) 1 49 Nylock Nut (M8 x 1.25) 8 50 W a sher (M6) 15 51 W a sher (M8) 14 52 Large W a sher (M8) 2 53 .
Sta mina Products, Inc. warra nts that this product will be free from defects in materi als a nd workma nshi p under normal use, service a nd proper operation for a period of 90 days on the parts a nd 5 years on the fra me from the date of the original purcha se from a n authorized retailer .
NOTES 18.
IMPORT ANT : Before filling out the form below ma ke sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach a nd M ail or Fax the Form Below Sta mina Products, Inc.
An important point after buying a device Stamina Products 55-1539A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stamina Products 55-1539A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stamina Products 55-1539A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stamina Products 55-1539A you will learn all the available features of the product, as well as information on its operation. The information that you get Stamina Products 55-1539A will certainly help you make a decision on the purchase.
If you already are a holder of Stamina Products 55-1539A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stamina Products 55-1539A.
However, one of the most important roles played by the user manual is to help in solving problems with Stamina Products 55-1539A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stamina Products 55-1539A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
