Instruction/ maintenance manual of the product UltraMic Plus Spirit
Go to page of 19
Featuring.
P age 2 SAFETY PRECAUTIONS The SPIRIT MONITOR 2 mixer must only be connected through the P ower Supply supplied. The wires in the mains lead are coloured in accordance with the following code: Earth: .
P age 3 INPUTS 24 Connecting Up.
USING MONITOR 2 Mono Input Channel XLR Input The UltraMic Plus padless input preamp is designed to accept BALANCED or UNBALANCED signals at a wide range of input levels up to +28dBu. When using microphones, professional dynamic, condenser or ribbon mics are best because these will be L OW IMPEDANCE.
P age 5 MONITOR SENDS These controls route the input channel signal to any one or more Monitor busses and the associated Monitor Outputs, allowing a number of unique monitor mixes to be created. The sends are arranged as a group of mono sends (1-8) and two stereo pairs (9/10 & 11/12).
P age 6 9 10 8 7 6 1 2 3 4 5 11 OUTPUT SECTION MONITOR OUTPUTS These outputs provide summing of the corresponding input channel monitor sends, and drive XLR -type output sockets from impedance balanced outputs. A break-point is included before each output socket for the connection of an external graphic equaliser .
P age 7 MASTER SECTION WEDGE SOURCE The Engineer s W edge outputs are normally fed from a mix of the MNTR feeds from outputs 1-12. The pre-fade wedge signal feeds the headphones and meters and the post-fade signal feeds the XLR outputs.
P age 8 Setting Up & T roubleshooting Initial Set Up Once you have connected up your system (see the sections on connection and wiring earlier in this manual for guidance) you are ready to set initial positions for the controls on your mixer .
P age 9 BAND INSTRUMENTS/VOCALS Live Monitor with Effects APPLICA TIONS.
BAND INSTRUMENTS/VOCALS P age 10 Live Monitor with In-Ear Monitoring.
P age 11 Theatre.
P age 12 FOH Console.
P age 13 FOH Console with Subgrouping.
P age 14 3 3 3 3 3 1 1 1 1 1 2 2 2 2 2 +48V +48V +48V +48V MIC INPUT SPLIT SPLIT OUTPUT (Internal Link) Link - Grounded No Link - Ground Lift TIP: SEND RING: RETURN HOUSE MICS FX RET 1 LEFT HOUSE FX R.
Balanced Unbalanced Insert Leads ’Y’ Leads (Unbalanced) Lamp Connections ’Y’ Leads (Balanced) Headphone Splitter P age 15 Connecting Leads.
Control Position Sheet Y ou may freely copy this page to mark control positions to assist in resetting the desk between performances..
P age 17 INPUTS MONITOR 2 CONSOLE T ypical Starting Out Control Positions.
P age 18 Specifications Noise Measured RMS, 22Hz to 22kHz Bandwidth. Inputs at unity gain and terminated 150 W Output Noise 24 inputs routed, sends down, master @ unity < -80dBu EIN Mic EIN @ max. gain (150 W terminated) -129dBu THD+N Mic sens. -10dBu, Faders @ unity , send at max.
A Harman International Company P art No: ZM0192.
An important point after buying a device Spirit UltraMic Plus (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Spirit UltraMic Plus yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Spirit UltraMic Plus - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Spirit UltraMic Plus you will learn all the available features of the product, as well as information on its operation. The information that you get Spirit UltraMic Plus will certainly help you make a decision on the purchase.
If you already are a holder of Spirit UltraMic Plus, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Spirit UltraMic Plus.
However, one of the most important roles played by the user manual is to help in solving problems with Spirit UltraMic Plus. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Spirit UltraMic Plus along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
