Instruction/ maintenance manual of the product BA-EN45 Banner American Products
Go to page of 17
OPERATING INSTRUCTIONS ENTRY 4500 Model No. BA-EN45 Banner American Products, Inc. Temecula, CA.
CAUTION... TO AVOID ANY DAMAGE, PLEASE DO NOT USE RAZORS OR SHARP OBJECTS NEAR THE ROLLERS..
Table of Contents I. For Your Safety ..................................................... 2 II. Electrical Safeguards ........................................... 2-3 III. Specifications ........................................................ 3 IV. Set-up .
Entry 4500 (BA-EN45) Mandrel.
u Do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. u Read all safety messages located in this instruction manual and on the laminator very care- fully.
u Do not operate the laminator with a damaged power supply cord or plug. u Replace fuses only with same type rated 30A, 240V and 1A, 250V fuses. Contact your dealer for replacement fuses. u There are two (2) EMERGENCY STOP buttons on your Entry 4500, one on each side.
Bottom Roll : With the gripper spring towards you, push the core gripper blade away from you and place the roll of film onto the mandrel so that the film unwinds away from you from the bottom of the roll. Turn the roll on the mandrel to lock the core gripper blade into the cardboard film core.
8. Turn the SPEED CONTROL knob far enough to allow the rollers to sufficiently pull the poster board into the laminator. Keep in mind that varying films, media, and temperatures will require different speeds. 9. Feed the poster board between the rollers.
Rewind Option for Pressure Sensitive Laminating....
VI. Pressure Sensitive Laminating... Note: You must have the Rewind Option for Pressure Sensitive Films in order to laminate with pressure sensitive material. 1. Load a roll of pressure sensitive film onto the supply mandrel so that it unwinds toward you from the bottom of the roll.
1. Load a roll of adhesive, with the liner wound to the outside, onto the top mandrel in the same manner as with laminating film. 2. Load a roll of paper on the bottom mandrel or use adhesive the same width as the mount board to keep the adhesive from accumulating on the rollers.
IX. Maintenance/Service... Always use caution when servicing your laminator. Precautions: Disconnect the power supply and open the panel breaker before attempting to service or repair the laminator. Any maintenance or service should be preformed only by those having appropriate technical training and experience.
3. Open the ROLLER RELEASE handle on the side of the laminator and pull the film out of the unit that has become wrapped around the rollers. 4. If you have a severe wrap-around, it may be necessary to use the REVERSE feature to back the film out. Be sure to pull the film away from the laminator.
Do’s and Don’ts... Read the instruction manual before operating your laminator. Always run test samples before laminating valuable items. Feed the print through slowly and evenly, smoothing it as it is pulled into the laminator.
XIII. Parts List and Illustrations T his section contains reference drawings and a parts list to assist you when ordering parts for your laminator. The drawings show only those parts that may be replaced by the dealer.
Item Part Number Description Quantity 61 557 KNOB, THERMOSTAT 2 62 11045 VARIABLE SPEED CONTROL 1 63 4096 CLAMP, POWER CORD 1 64 2379 MAIN BODY BRAKE FOR RL43 4 66 2378 BRAKE NUT FOR RL43 4 67 2777 SWITCH, JOURNAL, EMERGENC 2 68 11100 CAPACITOR, .
E xploded Assembly 13.
An important point after buying a device Banner American Products BA-EN45 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Banner American Products BA-EN45 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Banner American Products BA-EN45 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Banner American Products BA-EN45 you will learn all the available features of the product, as well as information on its operation. The information that you get Banner American Products BA-EN45 will certainly help you make a decision on the purchase.
If you already are a holder of Banner American Products BA-EN45, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Banner American Products BA-EN45.
However, one of the most important roles played by the user manual is to help in solving problems with Banner American Products BA-EN45. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Banner American Products BA-EN45 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
