Instruction/ maintenance manual of the product CR2032 Specialized
Go to page of 17
1 SPEEDZONE ® PR0 CYCLOCOMPUTER Congratulations on your purchase! Y ou are now the owner of the world’ s most advanced cyclocomputer . Y our Specialized SpeedZone® Pro is the first cycling computer to feature wireless digital transmitters for both speed and cadence sensing.
6. Magnet with screw (1) 7. Adhesive backed magnet 8. Cadence magnet (1) 9. Cable tie wraps (6) 10. Mounting bracket sizing straps (3) 11. Speed T ransmitter and mount (1) BA TTER Y INST ALLA TION AND REPLACEMENT Before using your SpeedZone® Pro Computer you will need to install the batter y .
MOUNTING THE SPEEDZONE® PRO: There are two transmitters includ- ed with your SpeedZone® Pro. One transmitter is for speed and the other is for cadence. Please note that that they are marked with a WHEEL (speed transmitter) icon or a CRANK (cadence transmitter) icon.
road and mountain bike handlebars. Attach the mount to the handlebar using the Philips head screw provid- ed. Tighten so that the bracket cannot rotate on the handlebar . There are several sizing shims provided to fit different diameter bars. If you are using the new 31.
"SPEEDID". The "Dot-matrix Display Area" may show a number (the code of the digital speed transmitter) or "- - -". If a number is shown, press the mode button once and "- - -" will be displayed. Now , spin your front wheel to activate the transmitter .
OPERA TION AND PROGRAMMING When your SpeedZone® Pro has not detected any speed input for 30 min- utes, it will enter sleep-mode in order to conser ve batter y power . During sleep mode only the analog and digi- tal clocks are displayed. Y ou will need to wake it up by pushing the "Mode", "Set" or "T op" button once.
called the odometer mode). Note: if your display says TRIP , press the "SET" button once to change to ODO. Next, hold down the "SET" button for three seconds. The "Km" or "m" indicator will begin blinking. Y ou may now alter- nate between miles and kilometers by pressing the "MODE" button.
4. Wheel Circumference Selection T o set the circumference for the type of tires you are using, you can use Specialized’ s "Easy Calibration Mode" or measure your actual tire circumference by the rollout method. T wo dif ferent tire diameters may be entered by using the computer’ s "Second Wheel Option.
3. Roll the wheel one complete revo- lution until the valve stem is again at the 6:00 position. Read the tape directly under the valve and note the distance in millimeters.
button to adjust the hour digits. AM/PM is selected by scrolling the hour digit. Press the "SET" button to accept the hour selection. The minutes will flash and can be adjusted by pressing the "MODE" button.
set to the desired settings. Press the "SET" button to exit programming mode. Once the time inter val timer is programmed, press the "TOP" button to start/stop the countdown. (See fig- ure 15). Note: The shortest inter val that can be set is 5 seconds.
COMPUTER FUNCTIONS Speedometer (SPEED)- Y our current speed is always shown by the long needle on the LCD screen. Each needle represents one M/h when miles is selected and two Km/h when kilometers is selected. The speed is also shown on the Digital Display Area up to 99.
Inter val Timer (INT)- The inter val timer is displayed on the lower line of the screen when (INT) appears on the left. The timer indi- cates the end of an inter val with one short beep per second for the last 4 seconds of the inter val. This is fol- lowed by a long beep, indicating the beginning of a new inter val.
Programmable Odometer The odometer digits are programma- ble. This is convenient for transferring your hard-earned mileage that is usu- ally lost when changing batteries or computers. INCLINOMETER (%GRD) The inclinometer will display the per- centage of grade you are climbing or descending in increments of 1%.
Speed/distance not recording: Check sensor/magnet alignment. Make sure that the sensor is no more than 1/16" (2mm) from the magnet. Replace transmitter batter y if neces- sar y .
Automatic Timer (A TM) 0 to 9hrs, 59min, 59sec. recycling type Inter val Timer (INT) 5 seconds to 9hrs, 59 min, 59 sec. Distance Countdown(DIST ) .01 to 999.
Note: This warranty does not pertain to batteries. No person or representative is author- ized to assume any liability on behalf of Specialized Bicycle Components, Inc.
An important point after buying a device Specialized CR2032 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Specialized CR2032 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Specialized CR2032 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Specialized CR2032 you will learn all the available features of the product, as well as information on its operation. The information that you get Specialized CR2032 will certainly help you make a decision on the purchase.
If you already are a holder of Specialized CR2032, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Specialized CR2032.
However, one of the most important roles played by the user manual is to help in solving problems with Specialized CR2032. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Specialized CR2032 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
