Instruction/ maintenance manual of the product M8809511 Spalding
Go to page of 16
1 07/06 ID# M8809511 In-Ground Basketball System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
2 ID# M8809511 07/06 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
3 07/06 ID# M8809511 24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. 2.
4 ID# M8809511 07/06 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 07/06 ID# M8809511 PLA YIN G SURF A CE Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2). Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 3 2 6 6 6 2 6 2 6 1 1 5 THREE PEOPLE REQUIRED FOR THIS PROCEDURE.
6 ID# M8809511 07/06 8. 7 14 27 13 27 12 12 27 27 27 27 14 27 13 7 THREE PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. W ARNING! Beginning with upper support arm (8) secure support arms to pole.
7 07/06 ID# M8809511 9. IMPORT ANT! Do Not Over Tighten. 8 14 13 27 27 10 13 27 27 9 Secure backboard to support arms (8 and 9) as shown. Use same hardware combination for attaching both elevator tubes to the backoard.
8 ID# M8809511 07/06 PLA YING SURF A CE 10. Secure jack brackets (21) to to mounting bracket as shown. 21 21 11 1 1. REAR VIEW 13 13 14 Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rot ating.
9 07/06 ID# M8809511 12. B. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. W ARNING! 12 14 27 27 13 27 27 13 REAR VIEW IMPORT ANT! Do Not Over Tighten. 9 9 20 20 27 A. Replace spacer in jack (20) with spacer (4).
10 ID# M8809511 07/06 28 13 21 15 15 13 14 20 Some adjustment will be necessary to align the lower crank jack and bushings to jack bracket s (21). NOTE: REAR VIEW TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
11 07/06 ID# M8809511 7 8 9 1 0 1 0 9 8 7 16 17 16 17 Apply height indicator labels (18 and 19) to height indicators (16). Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a phillips screwdriver . 14.
12 ID# M8809511 07/06 29 22 Attach rim assembly (29). For rim assembly, see instructions included with rim. Rim Assembly 16. IMPORT ANT! Carefully cut and peel protective film away from board prior to att aching rim. Remove rim cover prior to inst alling rim assembly to board.
13 07/06 ID# M8809511 Apply height adjustment label (31) to front of pole as shown. 18. REGULA TION RIM HEIGHT IS 10 FEET (3.05 m). 31 17. Check leveling at this time. Pole (5) should be level in all directions. After system is leveled, completely tighten nuts (2) above pole flange.
14 ID# M8809511 07/06 Rotate crank handle to raise or lower backboard. 20. Secure pole pad (32) as shown. 19. 32 Height Adjustment If height adjustment is difficult to operate, you may have over tightened the areas indicated. NOTE: Pole p ad may NOT be included in this model.
15 07/06 ID# M8809511 Item #10 (4) Item #1 1 (3) Item #17 (4) Item #24 (2) P ARTS LIST HARDW ARE IDENTIFIER (BOL TS) Item Qty. Part No. Description 1 4 200573 J-Bolt, 1/2-13 x 24” Long 2 12 265575 Nut, Hex, 5/8-11 3 1 900661 Anchor Plate 4 1 205714 Spacer, 0.
16 ID# M8809511 07/06 Item #25 (6) Item #26 (4)* Item #27 (28) Item #7 (2) Item #15 (2) * You May Have Extra Parts With This Model. Item #14 (1 1) Item #2 (12) Item #13 (20) Item #22 (4) Item #6 (8) H.
An important point after buying a device Spalding M8809511 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Spalding M8809511 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Spalding M8809511 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Spalding M8809511 you will learn all the available features of the product, as well as information on its operation. The information that you get Spalding M8809511 will certainly help you make a decision on the purchase.
If you already are a holder of Spalding M8809511, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Spalding M8809511.
However, one of the most important roles played by the user manual is to help in solving problems with Spalding M8809511. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Spalding M8809511 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
