Instruction/ maintenance manual of the product ATX 12V SOYO
Go to page of 97
• Please read the users guide be fore proceeding with your inst allation s. Seriou s damage may occu r if the procedu re is not followed pr operly . • This moth erboard does not support CP Us with a Vcore highe r than 1. 6 volts. P lease make sure the CPU y o u are using 1.
SY -P4I865PE Plus DRAGON 2 Motherboard ************************** ************************** mPGA Socket 478 Processor supported Intel 865PE AGP/PCI 400/533/800 MHz Front Si de Bus supported A TX 12V .
SOYO ™ SY -P4I865PE Plus DRAGON 2 iii Copyright © 2003 by Soyo Co mputer Inc. T rademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Pr oduct Rights: All names of the produ ct and corporate mentioned in this publi cation are used for identification purposes only .
T able of Contents SY -P4I865PE Plus DRAGON 2 iv T able of Co ntents CHAPTER 1 MOTHERBOARD DESCRIPTION ......... ............ .......... 1 1-1 INTROD UCTION ......... ................................................... ............ 1 1-2 UNP ACKING THE MOTHERBOARD .
T able of Contents SY -P4I865PE Plus DRAGON 2 v 3-4 ADV ANCED CHIPSET FEA TURES ... .............................. ........ 63 3-5 INTEGRA TED PERIPHERALS ....... ................ ............... .......... 65 3-6 POWE R MANAGEMENT SETUP . ..... .....
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 1 Chapter 1 MOTHERBOARD DESCRIPTION 1-1 INTRODUCTION The SY -P4I865PE Plu s DRAGON 2 AGP/PCI Moth erboard is a high-per formance Socke t 478 processor suppor ted A TX 12V form-fact or system board.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 2 One Back panel Wa r n i n g : Do not unpack th e Motherboa rd fr om its ant i-st atic packagi ng until you are rea dy to inst all it. Like most el ectronic equipment, your Mother board may be damaged by electrostatic discharge.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 3 1-3 KEY FEA TURES CPU Supports Int el® mPGA S ocket 478 processors : Pentium® 4 with and without Hyperthr eading, Northwood, P.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 4 S torage ICH5 integrated Se rial A T A controller supporting up to 2x UDMA 150 hard di sks ICH5 Integrate d Parallel A T A controller supporting up to 4x UDMA 33/66/ 100 Paralle l A T A dev ices.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 5 Wa r n i n g : Do not apply power if the Motherboard appears damaged . If the re is damage to t he board, cont act your dea ler immedi ately . 1-5 ELECTROST A TIC DISCHARGE PRECAUTIONS Make sure t o ground yoursel f befor e handling t he Mother board or other system compon ents.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 6 1-6 SY -P4I865PE PLUS DRAGON 2 MOTHERBOARD LA YOUT Back Panel SY -P4I865PE Lite DRAGO N 2 Platform PS/2 K B Connector PS/2 Mou se PS.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 7 1-7 SY -P4I865PE PLUS DRAGON 2 MOTHERB OARD COMPONENTS A BCDE F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD AE.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 8 A +12V Power Connec tor This is where the Power Supply's +12V A TX connector goes. For a lay-out of this connec tor ple ase check the F. A T X 1 2 V P o w e r Supply paragraph on page 3 5.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 9 H CPU Cooling Fan (CPUF AN1) connectors W ith t hese connecto rs you can at t ach the CPU fan or fans to your motherboard. They supply power and (in the case of CPUF AN1) allow you to m onitor the speed of the F AN via the SOYO Hardware Monitor software or vi a CMOS setup.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 10 O Chassis Cooling Fan (CHA F AN1) connector This co nne cto r is to con nec t yo ur ch assis fan to yo ur mo therb oard. This mother board supports up to 2 chassis fans. It allows you to monitor the spee d of CHAF AN1 in CMOS setup or by usi ng the SOYO Hardware Monitor software.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 11 V GAMEPOR T co nnector This co nn ecto r is to at tach yo ur gameport connec tor t o. Gamepor ts are used to con nect for example joy sticks to. For more details check the par agraph on page 30.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 12 AC AC97 Onboar d Au dio Chip AD Micr opho ne an d LAN S tatus LED Connec tor (J30) This connector allows you to extend your mi crophone conn ector and LAN Status LED to your front panel.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 13 Chapter 2 HARDW ARE INST ALLA TION Congratul ations on your pur chase of SY -P4I865PE P lus DRAGON 2 Motherboar d.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 14 2-2 IN ST ALLA TION GUIDE W e will now begin th e instal lation of th e Motherboar d. Plea se follow th e step-by-step p rocedure design ed to lead y ou to a co mplete and cor rect install ation.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 15 2. Align th e blunt edge of the CPU wi th the mat ching pi nhole disti nctive edge on the socket.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 16 4. Th en close the sock et handle to se cure the CPU in p lace. Remember to co nnect the CPU Co oling Fan to the app ropriate power connector on the Motherboard. The fa n is a key component that will ensure syst em stability .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 17 S tep 2 Install Memory Module This moth erboard suppor ts one Dual Channel t o your memory , Note that you can use normal DD R memory for D ual Channel to work. Also note that for Dual Channel to work 2 modules o f equal size and sp ecifications hav e to be installed .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 18 Memory Configuration T able If you want to use the Dual Channel feature, pl ease foll ow the memory configur ation table be low: Instal ling your memor y in a combina tion di fferent from th e tabl e above wil l still a llow you r sy stem to work.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 19 S tep 3 Inst allation of Exp ansion Cards The mothe rboar d has 1 AGP sl ot and 5 PCI slots. 1. Re ad the related expa nsio n card’ s instruction document before inserting the expansi on card i nto the computer .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 20 S tep 4 Connect cables, case wire, and power supply A.IDE Device In stallation (HDD, CD-ROM) This Mothe rboard offers 1 primar y (IDE1) IDE device connecto rs, 1 secondary IDE devi ce connect ors ( IDE2) and 2 te rtiary serial A T A ports.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 21 Note: I DE2 and SA T A2 ar e not boot able, SA T A1 and IDE1 are boot able. Note: Only W indows XP can use SA T A1, SA T A2, IDE1 and IDE2 at the same time.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 22 Serial A T A connectors Y ou ca n also plug t he seri al A T A cabl e into the serial A T A connector of the motherboar d. The other end of t he SA T A cable goe s into your SA T A device.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 23 B. Floppy Drive Installation The system support s 5 possible fl oppy drive t ypes: 720 KB, 1.2 MB, 1. 44 MB, 2.88 MB. In addition, thi s Motherboard sup ports a 3-mode (720KB/1.2MB/ 1.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 24 C. Front Pane l Connections Plug the c omputer case's front pa nel devi ces to t he correspondi ng hea ders on the Mothe rboard. 1. Power LED Please i nstall accordi ng to the f ollowi ng pin assi gnment: pi n 1, 3 are f or Power LED.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 25 2. Reset Plug t he Reset push-b utton c able in to the 2-pi n Reset hea der on t he Moth erboard. Push ing the R eset b ut ton o n the front pane l will caus e t he system to restar t the boot-up se quence.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 26 5. IDE LED Attach the 2-pin IDE device LED ca ble to the correspondi ng IDE LED header on the Motherboard. This will cause the LED to li ghten when an IDE1 o r IDE2 (HDD , CD-R OM) device is ac tive.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 27 D. Back Panel Connections All external devices such as the PS/2 ke yboard, PS/2 mouse, printer , modem, USB can be plugged di rectl y into the Mot herboard bac k panel.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 28 1. Onboar d Serial Port s COMA/COMB External peripherals that use seri al transmission scheme include: - serial (RS232) mice - modem. Plug the se rial devi ce cable s directl y into t he COMA/COMB 9-pi n male connectors located at the rear p anel of the Motherboard .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 29 5. Univer sal Serial Bus (USB1/US B2, USB3/USB4, USB20_1/USB20_2) This Motherboard provides 8 USB 2.0 po r ts for your addit ional devices. Plug the USB device jack into the av ailable USB connector USB1, U SB2, USB3 and USB4.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 30 The Gameport has the following lay-out : E. Other Connections 1. S tandard Infrared (SIRCON) Plug the 5- pin inf rared devi ce cable t o the SIRCON header . This will ena ble the infr ared transf er functi on.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 31 2. Coolin g Fan Install ation (1) CPU C ooling Fan (CPU F AN1) Afte r you have seat ed the CPU pr operly on t he processor , att ach the 3-pi n fan cable to the CPUF AN connector on the Mothe rboard.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 32 (2) Chassis Cooling Fan (CHAF AN1, CHAF AN2) Some chassis also feature a cooling fan. This Mother board features a CHAF AN connector to provide 12V powe r to the chassis fan. Connect the cable fr om the chassis f an to th e CHAF AN 3-pin connec tor .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 33 3. Smart Card Re ader The smart card reader confo rms to the PC/SC W orking gr oup standard, and has the following l ay-out: 4. CD Line-in (CDIN1) This Motherboard prov ides one CD-Line-in co nnectors.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 34 5. AUX-IN (AUXIN1) This Motherboard p rovides one AUX-IN conn ectors. Please connect the 4-pin audio cable from your second CD-ROM or DVD ROM drive to either AUX-IN. Please i nstall accor ding to the foll owing pin assignment : 6.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 35 F . A T X12V Power S upply The power supp ly connector is the la st connect ion to be made whi le install ing a mother board. Thi s mother board re quires an A TX 12V power supply (For P4 system), and A T or A TX power suppl y cannot be use d.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 36 3.3V -12V GN D PS -ON GN D GN D GN D -5V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW- OK 5VS B 12V AT X P o w e r Note 3: The mini mum .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 37 G . CMOS Cle ar (JP5) In some cases t he CMOS memory may contai n wrong data, f ollow the st eps below to c lear the CM OS memory . 1. Clear the CMOS memory by moment arily short ing pin 2-3 on jumpe r JP5.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 38 Onboard LAN LED Definition S tep 5 Power On Y ou have now complet ed the har dware i nstal lation of y our Mother boar d successfully .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 39 Repeat this operati on until you get the f ollowi ng screen. 3. Th e BIOS Setup screen ap pears: Phoenix – A ward BIOS CMOS Setup.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 40 Step1. Select [ST AND ARD CMOS S ETUP] Set [Date/T ime] and [Floppy drive type], then set [Hard Disk T ype] to “Auto”.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 41 Chapter 3 BIOS SETUP UTILITY This Mot herboard's BIOS setup progra m uses t he ROM PCI BI OS program from A ward Software Inc. T o enter the A ward BIOS pro gram 's Main Me nu: 1. Turn on or reboot the syst em.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 42 Hot Keys: Function keys give you a ccess t o a group of com mands throughout t he BIOS utility . Function Command Description F1 Gener al He lp Gives the list of opti ons available for each item. F5 Previ ous Va l u e s Restore the old values.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 43 SA VE AND EXIT SETUP Select the [SA VE & EXIT SETUP] option fro m th e M ain M enu to save data to CMOS and exit the set up utilit y . Th is opti on saves all your changes a nd causes the system to reboot.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 44 3-1 SOYO CO MBO FE A TURE This moth erboard does not use any hardw are ju mper s to s et th e CPU frequency .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 45 System P erf ormance Setting Description Note Normal Default Fast System Performance Tu r b o Adjust your computer ’ s perform ance. SOYO COMBO Feature Setting Description Note CPU Clock Ratio 8X~ 50X The available CPU ra tio you can se lect will depends on your CPU ID.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 46 SOYO C OMBO Fe ature (Contin ue) Setting Description Note Disabled Quick Power On Self T est Enabled P rovide s a fast POST at boot-up. Default Enabled C.I. H. 4 -W A Y Pr otection Dis able d This item allo ws y ou write -protect your BIOS chip.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 47 3-1.1 Adv anced D RAM Control Caution: Change these se ttings on ly if you are already fa miliar with DRAM timi ng parame ters . The [Adv anced DRAM Control] option changes the values of the chip set registers.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 48 CHIPSET FEA TURES SETUP (Continue) Setting Descript ion Note 2 3 DRAM RAS# to CAS# Delay 4 This item allo ws you to control DRAM RAS to CAS delay time. Default 2 3 DRAM RAS# Precharge 4 This item allo w you to control DRAM RAS percharge time.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 49 3-1.2 On board Device The [Onboard De vice] opti on changes the values of the chipset regi sters. These registers con trol the system op tions in the co mputer .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 50 3-1.3 OnChip IDE Device Caution: Change these set tings only if you are alr eady fami liar with th e IDE sett ings. The [OnChip IDE Devi ce] option changes t he settings of the 82801EB (ICH5) IDE controller .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 51 CHIPSET FEA TURES SETUP Setting Descri ption Note IDE only Only enabled IDE1,2. SA T A1,2 are disabled Defa ult SA T A only Only enable S A T A1,2. IDE1,2 are d isabled. Pri IDE+SA T A IDE1 and SA T A1,2 are enabled.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 52 IDE Device Controls Setting Description Not e Disabled T urn o ff the on-bo ard IDE On-Chip PCI IDE Primary Secondar y Enable d Use the on -bo.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 53 3-1.4 Boo t Device Order The [Boot De vice Or der] opti on allows you t o change t he order in which your system scans for de vices to boot fr om.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 54 System Boot Control Settings Setting Description Note Floppy LS120 IDE1/SA T A1 CDROM ZIP100 Other Device First /Sec ond/Thi rd Boot Device Dis able d Selects the order in which your system scans for devi ces to boot from (First th e first boot device, t hen the second, etc…).
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 55 3-2 ST ANDARD CMOS SETUP Select the [ST ANDARD CMOS SETUP] opt ion fr om the Main Menu and press [Enter ] key .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 56 Hard Disks T ype & Mode Choose the type and mode for the hard disks that you have alr eady install ed.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 57 Others Optional Setting Description Note EGA/VGA Default CGA 40 CGA 80 Vi d e o MONO (Monochr ome) Selec t the vid eo m ode. ALL Error s Default No Errors All, But Keyboard All, But D i skette Halt On All, But Di sk/Key When the BIO S detects system errors, this fun ction w ill stop the syste m.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 58 3-3 ADV ANCED BIOS FEA TURES Select the [Adv anced BIOS Features] option fr om the Main Menu and press [Ente r] key .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 59 V irus W arning Setting Descriptio n Note Disabled Default V irus W arnin g Enabled Allows you to choose the VIRUS warning featu re for IDE Hard Disk boot s ector protecti on.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 60 Boot Up NumLock St atus Setting Description Note On N umeric keypad in numeric mode at boot -up. Default Boot Up NumLock St a t u s Of f Puts numeric keyp ad in arrow key mode at boot-up. Gate A20 Opti ons Setting Descriptio n Note Normal A pin i n the keyboar d control ler controls G ateA2 0.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 61 Security Option Use this feature to p rev ent unaut horized syste m b oot-u p or use of BIOS Setup. The following table describes th e security setti ngs. Setting Descriptio n Note Setup If a password is set, the password prompt only appears when you attempt to enter the BI OS Setup p rogram .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 62 LOGO Show Setting Descriptio n Note Disabled Full Screen LOGO Show Enab led Set Enabled to Show Logo (DRAGON). Defa ult LOG0 Default EP A LOGO SELECT LOG1 Allows user to display SOYO logo or own logo. Logo-0 shows SOYO logo, Logo -1 shows user logo .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 63 3-4 ADV ANCED CHIPSET FEA T URES Caution: Change these se ttings on ly if you are already fa miliar with the Ch ips et. The [Advance d Chipset Fe atures] opt ion changes the values of the chipset registers.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 64 CHIPSET FEA TURES SETUP Setting Description Note Disabled Default System BIOS Cacheable Enab led The ROM area F0000H-FFFFFH is cacheable. Disabled Default Vi d e o B I O S Cacheable Enab led The video BIOS area at C0000H-C7FFFH is cach eable.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 65 3-5 INTEGRA TE D PERIPHERALS Caution: Change these se ttings on ly if you are already fa miliar with the Ch ips et. The [INTEGRA TED PERIPHERALS ] opti on changes the values of the chipset registers. These registers contro l the system options in the computer .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 66 3-5.1 Onboa rd USB Device This [Onboar d USB Device] opti on chan ges the value s of the onboard USB controll er . The following screen show s setup default setti ng. Phoenix – A ward BIOS CMOS Setup Uti lity Onboard US B Devic e USB Controller Enabled USB 2.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 67 3-5.2 Supe rIO Device Caution: Change these se ttings on ly if you r are already fa miliar with the Ch ips et. The [Sup erIO Device] option chan ges the values of the Sup er I/O controller . The following screen show s setup default setti ngs.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 68 Others Optional Setting Descript ion Note Password Enables you to wa ke-up the system by entering a password on the keyboard. Hot KEY Y ou can wake-up the system by pressing t he key combinat ion of your choice ( Ctrl-F1~F12) .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 69 Onb oard Seri al Po rts Setting Descriptio n Note Normal Default IrDA ASKIR UAR T Mode Select SCR The second serial p ort offe rs several special modes. It can either work as an infrared device (IrDA, ASKIR) or as a Smart Card reader (SCR), o r as a normal serial port.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 70 Others Optional Setting D escript ion Note On The system will switch on when power comes back after a power failure.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 71 3-6 POWER MA NAG EMENT SETUP The [POWER MANAG EMENT SETUP] se ts the system's power saving functions.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 72 Power Management Controls Setting Description Note S1(POS) Default S3(STR) ACPI Su spend Ty p e S1 & S3 This item a llows yo u select suspend mode. Auto Default Ye s Run VGABIOS if S3 Resume No Some OS (win xp/ 2k) re quire to load VGABIOS afte r resume from S3.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 73 Power Manageme nt Controls (Co ntinue) Setting Descript ion Note Disabled Defa ult HDD Power Down 1- 15Min When the set time has elapsed, BIOS sends a command to the HDD to power down. This turns of f the HDD moto r .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 74 Reload Global T imer Event s Setting Description Note Disabled Defa ult IDE0, IDE1 Primary Secondary Enabled In ef fect, t he system remains alert for anything which occurs to a devic e which is c onfigured as Enabled .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 75 3-7 PNP/PCI CONFIGUR A TION SETUP This option se ts the Mother board's PCI conf igurati on. Phoenix – A ward BIOS CMOS Setup Uti lity PnP/PCI C.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 76 PNP/PCI Config ur ation Co ntrols Setting Descript ion Note Disabled Retain PnP configuration data in BIOS. Default Rese t Confi gu ratio n Data Enabled Reset PnP c onfigurati on data in BIOS. Manual BIOS does not manage PCI/I SA P nP card IR Q a ssig nment.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 77 PNP/PCI Config uratio n Setup (Continued) Setting Descript ion Note How to set the BIOS to r elease the IRQ to the PnP Interrupt pool: Interrupt Line .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 78 3-8 PC HEAL TH ST A TUS This option sets the Mother board's PC Health Status. Phoenix – A ward BIOS CMOS Setup Uti lity PC Health S tatus CPU Vcore 1.72 V Item Help +3.3V 3.21 V +5V 5.02 V +12V 1 1 .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 79 3-9 LOAD F AIL-SAFE DEF AUL TS Select the [Load Fail-S afe Default s] option fr om the Main Menu t o load a pre-defined safe bios se ttings.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 80 3-10 LOAD OPT IMIZED DEF AUL TS Selec t the [Loa d Op timiz ed D efaults ] o ptio n from the M ain M enu to loa d the pre- defined opti mized BIOS setti ngs.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 81 3-11 SUPER VISOR P ASSWORD Based on the set ting you have made i n the [Securit y Option] of the [Advan ced BIOS Feature] section, the pa ssword prevents access to the system or the se tup progra m by unauthor ized use rs.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 82 3. Enter your new pa ssword and press [Ent er]. The following message appears, prompti ng to confirm t he new password: 4.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 83 Boot Men u Boot Me nu enable s user to boot -up on dif fere nt bo ot devi ce wit hou t going into the BIOS setup.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 84 Chapter 4 DRIVER S INST ALLA TIO N The S OYO-CD wi ll Aut o Run on ly in Windows Bas ed Ope rating Systems. Y our SY -P4I 865PE Plus DRAGON 2 Mo therboard comes with a CD-ROM label ed “SOYO CD”.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 85 The user's ma nual f iles i ncluded o n th e SOYO CD are in PDF (Postscript Document Format) . In order t o read a PDF file, th e appropr iate Acrobat Reader software must b e in stalled in your system.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 86 Step 2. Install Driver s and Ut ilities Highli ght the dri ver you want t o inst al l and then cl ick ok. The Start Up program di splays th e drivers a vailable for the partic ular model of Motherboar d you own.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 87 C-MEDIA Audio Driver for Win 9x/ME/2000/NT/XP The driver support s 2/4/6 sp eake rs 3D positional audio. P4I865PE DRAGON 2 hardwa re mo nitor for Win 9x/ME/2000/NT/ XP Y our motherboard comes w ith a hard ware mo nitoring IC.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 88 After W indows XP install ation, your de vice manager shoul d look l ike th is:.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 89 After dri ver inst allation, your W indows XP device manager shoul d look like this: N ote: T o install the USB 2.0 drive r , pl ease upd ate t o W i ndows XP service pack 1. Check chapter 5 for more info.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 90 Driv ers di rect ory li st i n the CD driv er.
Inte l USB 2. 0 Dr iver In stalla tion SY - P4I865PE Plus DRAGON 2 91 Chapter 5 INTEL USB 2.0 DR IVER INST ALLA TION For Windows XP USB 2.0 drivers are available for d o wnload using Wi ndows Update for Windows XP. For addition al information reg ardi n g USB 2.
Inte l USB 2. 0 Dr iver In stalla tion SY - P4I865PE Plus DRAGON 2 92 10.Choose [Se arch f or a suitab le driver for my device] . 11.Cli ck [Next]. 12.Choose [Sp ecif y a locati on] un der "Op tiona l searc h lo catio ns". 13.Cli ck [Next]. 14.
An important point after buying a device SOYO ATX 12V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought SOYO ATX 12V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data SOYO ATX 12V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, SOYO ATX 12V you will learn all the available features of the product, as well as information on its operation. The information that you get SOYO ATX 12V will certainly help you make a decision on the purchase.
If you already are a holder of SOYO ATX 12V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime SOYO ATX 12V.
However, one of the most important roles played by the user manual is to help in solving problems with SOYO ATX 12V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device SOYO ATX 12V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
