Instruction/ maintenance manual of the product STM.58B Source Technologies
Go to page of 12
Rev . 1.0 All specifications are subject to change without notice MOBILE PRINTER MODEL : STm.58b.
1 T able of Contents 1. Unpacking 2 2. Product overview 3 3. Usage and Installation 4 3-1. Control panel usage 4 3-2. Battery Installation 5 3-3. Battery removal 6 3-4. Battery char ging 7 3-5. Battery char ger usage 8 3-6. Usage of Cigar Jack for char ging 9 3-7.
2 3 2. Pr oduct overview P aper feed button Open Button P ower switch SERIAL USB Belt clip hole Battery DC P ower Front Rear 1. Unpacking Printer Battery Serial Cable Roll paper Belt Buckle USB Cable .
4 5 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not char ged at the time of your purchase, char ge the battery pr.
6 7 NOTE 1. Unless the exclusive char ger is used provided by the manufactur er , the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before r emoving the battery , make sure that power is turned off. 3. Printer does not work in the status of being connected with char ger only .
8 9 Connect the car cigar JACK char ger into the printer or battery holder . 3-6 Usage of Cigar Jack for char ging Printer Battery holder NOTE Use the Cigar Jack offered by the manufacturer .
10 11 1 2 3 4 Press the PUSH button to open the paper cover Pull a short length of paper out of the printer and close the cover . Insert the paper in the right direction T ear off the additional paper using tear bar . 3-8 Roll Paper installation 1 2 As shown in the picture, tighten the scr ew with a screw driver .
12 13 1 2 3 NOTE T urn off the power pressing the power button for approximately 3 seconds. The printout is produced. While you are pr essing the FEED button, press the power button 3-10 Self T est 1. T o print ASCII pattern additionally , press the Feed button once mor e 2.
14 15 Insert and swipe the card in the direction of the arr ow as shown in the picture. 3-11 MSR usage Optional When the printer is installed initially or when you face a problem, you can run the self.
16 17 Serial USB 4-2 Interface Cable Connection 1. Connect USB or Serial cable into the cable connector on the printer . 2. Connect the interface cable into the USB or Serial por t of the device (PDA, PC, etc.) NOTE Use the cable offered by the manufacturer (USB, Serial) 1.
18 19 6. Cer tification Printing Method Direct T hermal Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI Character F ont A (12X24), Font B (9X17) Character per line Font A : 32 columns , Font B :.
20 21 7. Setting up the softwar e Please refer to the programming manual included in CD. C A UTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.
An important point after buying a device Source Technologies STM.58B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Source Technologies STM.58B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Source Technologies STM.58B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Source Technologies STM.58B you will learn all the available features of the product, as well as information on its operation. The information that you get Source Technologies STM.58B will certainly help you make a decision on the purchase.
If you already are a holder of Source Technologies STM.58B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Source Technologies STM.58B.
However, one of the most important roles played by the user manual is to help in solving problems with Source Technologies STM.58B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Source Technologies STM.58B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
