Instruction/ maintenance manual of the product STM.117W Source Technologies
Go to page of 13
Rev . 1.0 All specifications are subject to change without notice MOB ILE PRI NTE R MODEL : STm.117w.
1 T able of Contents 1. Unpacking 3 2. Product overview 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery char ging 7 3-4. Battery char ger usage 8 3-5. Usage of Cigar Jack for char ging 9 3-6. Roll paper installation 10 3-7.
2 3 2. Pr oduct overview P aper feed button P ower switch DC P ower Battery SERIAL USB Open Button Front Rear 1. Unpacking Printer Battery Serial Cable Roll paper USB Cable Shielded Charger CD Quick M.
4 5 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not char ged at the time of your purchase, char ge the battery prior to using the printer (Battery char ger or Cradle can be used to char ge) CAUTION Risk of explosion if battery is replaced by an incorr ect type.
6 7 3-4-1 The status of lamp in char ging 3-3-1 The status of lamp in char ging Status char ging charging complete Status char ging charging complete Char ging Lamp Char ging Lamp Red Red Green Green NOTE In the case the battery is not fixed properly in the holder , the red lamp will be blinking, Then, extract and reinsert the battery .
8 9 1 2 3 4 Press the PUSH button to open the paper cover Pull a short length of paper out of the printer and close the cover . Insert the paper in the right direction T ear off the additional paper using tear bar . 3-6 Roll Paper installation Connect the car cigar JACK char ger into the printer or battery holder .
10 11 1 2 3 NOTE T urn off the power pressing the power button for approximately 3 seconds. The printout is produced. While you are pr essing the FEED button, press the power button 3-8 Self T est 1. T o print ASCII pattern additionally , press the Feed button once mor e 2.
12 13 When the printer is installed initially or when you face a problem, you can run the self test and check the information about -Control Cir cuit, Mechanism, Print Quality , ROM V ersion After checking with self-test and no issues are found, you can examine other devices and software.
14 15 4-2 Interface Cable Connection 1. Connect USB or Serial cable into the cable connector on the printer . 2. Connect the interface cable into the USB or Serial por t of the device (PDA, PC, etc.) NOTE Use the cable offered by the manufacturer (USB, Serial) Serial USB 5.
16 17 6. Pritner Specification 6-1 Specification Printing Method Direct T hermal Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI Character CPCL 7 Different Font Size (12~48pt) ESC/POS Font A (1.
18 19 Printer Comm ands Compatibility PRINT ○ FORM ○ JOURNAL ○ UNITS ○ Comments ○ TEXT Compatibility TEXT ○ FONT -GROUP(FG) ○ TEXT CONCA TENA TION ○ MUL TILINE(ML) ○ COUNT ○ SETMAG.
20 21 Line Print Mode Compatibility SETLP ○ SETLF ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET -TOF ○ SETLP-TIMEOUT ○ FCC Inform ation T his device complies with part 15 of the FCC Results.
22 23 CA UTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.
An important point after buying a device Source Technologies STM.117W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Source Technologies STM.117W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Source Technologies STM.117W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Source Technologies STM.117W you will learn all the available features of the product, as well as information on its operation. The information that you get Source Technologies STM.117W will certainly help you make a decision on the purchase.
If you already are a holder of Source Technologies STM.117W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Source Technologies STM.117W.
However, one of the most important roles played by the user manual is to help in solving problems with Source Technologies STM.117W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Source Technologies STM.117W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
