Instruction/ maintenance manual of the product VPL-EX175 Sony
Go to page of 46
DA T A PROJECT OR VPL-EX100 VPL-EX120 VPL-EX145 VPL-EX175 VPL-FX30 VPL-FX35 VPL-FX500L VPL-F400X VPL-F500X VPL-F700XL PRO T OC OL M ANU AL 1st Edition (Revised 1).
VPL-FX30 ! 警告 このマニュアルは，サービス専用です。 お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災， 人.
1 (T) VPL-FX30 T able of Contents 1. Overview 1-1. Introduction ........................................................................ 1 1-2. Glossary of T erms .............................................................. 1 1-3. Protocol Stack Structure .
.
1 VPL-FX30 1. Overview 1-1. Introduction The projector is remotely controllable over RS-232C as well as Ethernet. It is useful for setting up the projector away from the operator . This protocol manual describes the speci fi cations such as packet format and procedures for controlling the projector .
2 VPL-FX30 RS-232C Simplified Command Asynchronous Sub Command AMX Device Discovery SDAP SDCP Specific Command SNMP DDDP PJLink HTTP UDP/IP Ethernet TCP/IP SDCP (PJ T alk) Sub Command Simplified Command (1) RS-232C Fig.
3 VPL-FX30 2. Common Commands 2-1. Sub Commands Sub Command is the value which is used by Simpli fi ed Command. V alue is assigned for executing func- tion. For example, if you want to change the picture mode, the appropriate value assigned for the desired picture mode should be chosen.
4 VPL-FX30 ITEM List For Screen <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte ASPECT 00h 20h FULL 0000h Set/Get NORMAL 0001h ZOOM 0003h FULL1 0007h FU.
5 VPL-FX30 ITEM List For Status <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte ST A TUS ERROR1 01h 01h NO ERROR 00h Get only LAMP ERROR 01h F AN ERROR .
6 VPL-FX30 VPL-FX500L/F700XL ITEM List For Picture <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte PICTURE MODE 00h 02h DYNAMIC 0000h Set/Get ST ANDARD .
7 VPL-FX30 ITEM List For Setup <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte INPUT TERMINAL 00h 01h VIDEO 0000h Set/Get SVIDEO 0001h INPUT A 0002h INP.
8 VPL-FX30 ITEM List For Status <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte ST A TUS ERROR1 01h 01h NO ERROR 00h Get only LAMP ERROR 01h F AN ERROR .
9 VPL-FX30 VPL-EX100/EX120/EX145/EX175 ITEM List For Picture <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte PICTURE MODE 00h 02h DYNAMIC 0000h Set/Get .
10 VPL-FX30 ITEM List For Setup <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte INPUT TERMINAL 00h 01h VIDEO 0000h Set/Get SVIDEO 0001h INPUT A 0002h IN.
11 VPL-FX30 ITEM List For Status <T able 1> <T able 2> Remarks Item Number Data Item Upper byte Lower byte Data Byte ST A TUS ERROR1 01h 01h NO ERROR 00h Get only LAMP ERROR 01h F AN ERROR.
12 VPL-FX30 2-1-2. Infrared Remote Command Code VPL-FX30/FX35/F400L/F500X 15bit category x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 0x BLACK LEVEL ADJ TOGGLE PICTURE ADJ TOGGLE 1x VOL LARGE VOL S.
13 VPL-FX30 VPL-FX500L/F700XL 15bit category x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 0x BLACK LEVEL ADJ TOGGLE PICTURE ADJ TOGGLE 1x VOL LARGE VOL SMALL AUDIO MUTING POWER TOGGLE CONTRAST + CO.
14 VPL-FX30 VPL-EX100/EX120/EX145/EX175 15bit category x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 0x BLACK LEVEL ADJ TOGGLE PICTURE ADJ TOGGLE 1x VOL LARGE VOL:SMALL AUDIO MUTING POWER TOGGLE CON.
15 VPL-FX30 2-2. Reply <T able 3> Item Number Data Item Data Upper byte Lower byte ACK Complete 00h 00h NAK Unde fi ned Command 01h 01h Size Error 04h Select Error 05h Range Over 06h Not Applic.
16 VPL-FX30 D4 D5 D6 D7 (MSB) (LSB) (EVEN) BIT P ARITY STOP BIT ST ART D3 D2 D1 D0 3. RS-232C 3-1. Connection Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable. The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.
17 VPL-FX30 3-3. Communication Procedure 3-3-1. Outline of Communication All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the command block format. Communication is started by the issue of a command at CONTROLLER and ended when the return data is sent to CONTROLLER after DEVICE receives the command.
18 VPL-FX30 ST ART CODE B0 B1 B2 B4 B3 DA T A ITEM NUMBER TYPE CHECK SUM * 1 END CODE B5 B6 B7 [A9h] Put the item number . Refer to the item list in the sections 2-1-1 and 2-1-2. SET : 00h (Set data) GET : 01h (Get data) SET : Put the Data value described in the item list in the sections 2-1-1 and 2-1-2.
19 VPL-FX30 3-7. Packet Examples 3-7-1. Change “ASPECT” to “ZOOM” ST AR T CODE = A9h ITEM NUMBER = 0020h (ASPECT) SET/GET = 00h (SET) DA T A = 0003h (ZOOM) CHECK SUM = 23h END CODE = 9Ah Y ou will receive the packet below if the process is successfully completed.
20 VPL-FX30 4. Ethernet Ethernet corresponding model VPL-FX30, VPL-FX35, VPL-FX500L, VPL-F400X, VPL-F500X, VPL-F700XL, VPL-EX145, VPL- EX175 4-1. Service 4-1-1. Advertisement The advertisement service is provided to facilitate development of a PC application that can automatically detect a projector on the network.
21 VPL-FX30 4-1-2. PJ T alk By using PJ T alk, it is possible to communicate with PROJECTOR over Ethernet network. Both of set and get method are provided.
22 VPL-FX30 CONTROLLER PROJECTOR SDCP SET/GET Request Response (OK/NG) The command is executed if it’s valid. Then, the receive command is sent to the CONTROLLER. SDAP Broadcast SDAP Broadcast 4-2. Communication Procedure Communication sequence is shown below .
23 VPL-FX30 HEADER (4) COMMUNITY (4) PRODUCT NAME (12) SERIAL NO. (4) LOCA TION (24) POWER ST A TUS (2) VERSION (1) 4441h (2) CA TEGORY (1) COMMUNITY (4) 4-3. Protocols 4-3-1. SDAP This section describes the SDAP packet structure. The number in the brackets shows byte.
24 VPL-FX30 HEADER(2) COMMUNITY(4) COMMAND(4) DA T A(n) VERSION(1) CA TEGORY(1) 4-3-2. SDCP 1. Packet Structure The Fig. 4-5 shows SDCP packet format. The number in the brackets shows byte. The statement for each fi eld is described bellow . Fig. 4-5 SDCP Packet Structure 2.
25 VPL-FX30 REQUEST(1) ITEM NO(2) DA T A LENGTH(1) 4. COMMAND Field There are 2 types of COMMAND fi eld, which are REQUEST and RESPONSE. REQUEST command is sent to the PROJECTOR from CONTROLLER. On the other hand, RESPONSE command is sent by PROJECTOR as a response to the REQUEST command.
26 VPL-FX30 RESPONSE(1) ITEM NO(2) DA T A LENGTH(1) OK[01h] ITEM NO(2) DA T A LENGTH[00h] OK[01h] ITEM NO(2) DA T A LENGTH(2) NG[00h] ITEM NO(2) DA T A LENGTH(2) (2) RESPONSE Command COMMAND fi eld for RESPONSE has 3 sub fi eld shown as follows. Fig.
27 VPL-FX30 5. DA T A Field The content to be fi lled in this fi eld depends on the COMMAND fi eld. For SET Request commands, appropriate DA T A value accompanied with ITEM NO should be chosen. ITEM NO (item number) and its data is shown in the section 2-1-1.
28 VPL-FX30 0x8001 Model name Alphanumeric 12 characters If the number of characters is less than 12, the remaining digits are fi lled with 00h. 0x8002 Serial number 4 bytes n The serial number is in the range of 00000000 to 99999999.
29 VPL-FX30 7. ERROR CODE ERROR CODE has 2 bytes long. The table below shows the error code. Each error category is explained in the subsequent sections.
30 VPL-FX30 (1) Item Error This error occurs when the Item No. of a request is illegal or its data is illegal. The conditions for occur - rence of the respective errors are shown below . Invalid Item An unsupported Item No. is speci fi ed. Example 1: The unsupported category A**h is speci fi ed.
31 VPL-FX30 (3) Request Error This error occurs when header or command is illegal. The conditions of occurrence of the respective errors are shown below . Invalid V ersion The version of the header is other than 2. Invalid Category The category does not match.
32 VPL-FX30 (5) Comm Error Communication between Ethernet controller and main CPU has been failed. Timeout T imeout occurred. Check Sum Error A check sum error occurred. Framing Error A framing error occurred. Parity Error A parity error occurred. Over Run Err or An overrun error occurred.
33 VPL-FX30 4-3-4. PJLink The following model is equipped with the PJLink class1 protocol. For details about this protocol, refer to the PJLink speci fi cations published from JBMIA. Y ou can turn on or off the PJLink protocol and set a password from the W eb setting screen > Setup > Advanced Menu > PJLINK.
34 VPL-FX30 Command Data Remark ERST ? The following values are returned: 6th digit : Fan error 5th digit : Lamp error 4th digit : T emperature error 3rd digit : Cover open error 2nd digit : Filter er.
35 VPL-FX30 . Commands The following 14 commands are supported : (01) [Power control command] POWR (02) [Power status inquiry] POWR ? (03) [Input switch command] INPT (04) [Input switch inquiry] INPT .
36 VPL-FX30 (2) [Power status inquiry] POWR? This command obtains the projector ’ s power status. The projector responds as follows: Returns the following values when the power status is obtained: Standby or power-saving state : Returns “0”. Power ON state : Returns “1”.
37 VPL-FX30 (4) [Input switch inquiry] INPT? This command obtains the projector ’ s input status. The projector responds examples as follows: Returns the following values when the input status is obtained (The input channel varies depending on the model.
38 VPL-FX30 (7) [Error status inquiry] ERST? This command obtains the projector ’ s error status. The projector responds as follows: Returns the response for the error status in the following format. The error status is expressed with a six-digit number .
39 VPL-FX30 (9) [Input switch list inquiry] INST? This command obtains the input switch list. The projector responds as follows: When normal : Returns a source No. whose input can be switched. The source Nos. examples are as follows : (The input channel varies depending on the model.
40 VPL-FX30 (13) [Other information inquiry] INFO? This command obtains other information. The projector responds as follows: When normal : Returns a space. Projector error occurring (including warning) : Returns “ERR4”. (14) [Class information inquiry] CLSS? This command obtains the class information.
VPL-FX30 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or t.
Sony Corporation VPL-EX100 (CN) VPL-EX100 (SY) VPL-EX120 (CN) VPL-EX120 (SY) VPL-EX145 (CN) VPL-EX145 (SY) VPL-EX175 (CN) VPL-EX175 (SY) VPL-FX30 (SY) VPL-FX35 (SY) VPL-FX500L (SY) VPL-F400X (CN) VPL-F500X (CN) VPL-F700XL (CN) E 9-968-756-02 Printed in Japan 2010.
An important point after buying a device Sony VPL-EX175 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony VPL-EX175 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony VPL-EX175 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony VPL-EX175 you will learn all the available features of the product, as well as information on its operation. The information that you get Sony VPL-EX175 will certainly help you make a decision on the purchase.
If you already are a holder of Sony VPL-EX175, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony VPL-EX175.
However, one of the most important roles played by the user manual is to help in solving problems with Sony VPL-EX175. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony VPL-EX175 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
