Instruction/ maintenance manual of the product SDX-700C Sony
Go to page of 32
AIT Drive 2-676-745- 31 (1) 2006 Sony Corporation AIT-3 Ex TAPE DRIVE SDX-800V Series User’s Guide.
2 This document contains proprietary information which is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Sony. The information contained in this document is subject to change without notice.
3 IMPORTANT SAFEGUARDS For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance, or described in the operating instructions and adhere to them.
4 INSTALLATION Water and Moisture – Do not use power-line operated units near water – for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
5 Table of Contents Overview .................................................................................................................. 6 Introduction ............................................................................................
6 Overview The Sony SDX-800V series drives are high capacity data storage devices using Advanced Intelligent tape (AIT) technology. The SDX-800V series drives achieve high data reliability through Read-After-Write, an additional level of Error Correction Code, and other features.
7 Introduction About AIT Drives SDX-800V series drives are internal AIT drive units that use data cartridges conforming to the AIT-3 Ex format. SDX-800V series drives support AIT-1, AIT-2, AIT-3 and AIT-3 Ex formats.
8 Precautions Useable Cartridges SDX-800V series can be used with data cartridges marked with the AIT-1 * , AIT-2 * , AIT-3 or AIT-3 Ex logo. * Read only Notes • Be sure to use only data cartridges designed specifically for AIT (do not use 8 mm video cartridges) as this may damage the drives.
9 Transportation • Keep the original packing materials to facilitate safe transportation of the drives. • Always remove the tape/media cartridge before moving the drives. After removing the drives from the computer, repack them into their original packing.
10 Installation SCSI Connection/Setting the SCSI ID SCSI 68pin Connector 5 V Power Connector 1 2 3 4 GND GND 12 V Disable Enable Parity Note : = = = CLOSED/Jumper Don’ t care OPEN/Jumper not installed Pa rity Disable No Connection SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 Jumpers SCSI ID SCSI ID 0 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 2 1 0 P .
11 Option Switches (DIP Switch) DIP Switch Positions Default ON OFF 12345678 DIP Switch 1 DR (Disaster Recovery) Mode (OFF) 2 Emulation Mode (OFF) 3 AIT Library Interface Mode (ON) 4 Reserved (OFF) 5 .
12 DR (Disaster Recovery * ) Mode To enable DR Mode, set position 1 [Drive Mode] switch to ON. ON OFF 12345678 * In Disaster Recovery Mode, an SDX-800V series drive enters the DR Standby Mode 15 seconds after you insert a write-protected tape into the drive, and all the drive LED blink.
13 Library Mode The Library Mode can be enabled with a DIP switch. ON OFF 12345678 When switch 3 is ON, AIT-1, 2, 3 compatible Library Mode is enabled. With this switch OFF, ACI Mode is enabled. Terminator Power Control DIP switch This DIP switch determines whether terminator power is supplied to the SCSI bus.
14 Mounting Holes For 3.5" Standard Height 155.0 0.5mm [6.10" 0.02"] 90.0 0.3mm [3.54" 0.01"] 60.0 0.3mm [2.36" 0.01"] 70.0 0.3mm [2.76" 0.01"] 31.0 0.3mm [1.22" 0.01"] 21.0 0.3mm [0.83" 0.01"] 41.
15 Reconfiguring from 5.25" Model to 3.5" Model You can reconfigure the 5.25" model to the 3.5" model yourself. 1 Remove the 2 screws for each side rail.
16 Orientation 10 10 10 10 10 10 10 10.
17 Attaching and Removing the Dust Cover Attaching the Dust Cover 1 Align the dust cover’s hinge clips (one on each side) with the pins of the drive bezel. • The dust cover should be positioned so that the magnets * on the cover’s back face the drive bezel.
18 2 Press down at an angle on each side in turn until you hear the hinge clips click into place. Caution Do not press the dust cover in horizontally from the front. Doing so could cause the dust cover to break. 3 Close the dust cover. This completes attachment of the dust cover.
19 Removing the Dust Cover 1 Open the dust cover. 2 Holding the dust cover at both corners, carefully raise the dust cover. The dust cover hinge clips and drive bezel pins uncouple.
20 Operation Location of 3 LEDs There are three LED indicatiors (TAPE MOTION LED, CLEANING REQUEST LED, REPLACE TAPE LED) and an EJECT button on the front panel of the SDX-800V series drives.
21 Drive Operation Loading a Cartridge Note While setting the data cartridge, do not turn off the host computer. This may cause a malfunction or damage data. 1 Turn on the host computer. Check that the drive’s TAPE MOTION LED, CLEANING REQUEST LED and REPLACE TAPE LED go off.
22 Unloading a Cartridge The cartridge can be removed from SDX-800V series drives in response to a SCSI Unload command, or by pressing the EJECT button.
23 How to Clean 1 Load the cleaning cartridge (SDX3X-CL) into the SDX-800V. Cleaning starts automatically. 2 Cleaning takes from a few seconds to a minute for the SDX- 800V, *1 and the cartridge is automatically ejected when finished. *1 The cleaning time varies depending on the condition of the drive.
24 Reel motor Loading motor Emergency Tape Removal Procedure 1 Remove the drive from the chassis or enclosure to allow access to the bottom of the drive. 2 Remove the drive’s top cover. 3 Locate the small opening in the bottom of the drive and insert the tip of a precision screwdriver so that the Loading motor shaft can be rotated.
25 Caution Stop rotating the motor shaft immediately, when the guide B gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge).
26 Interface Implementation Supported SCSI Messages Abort Identify Target Reset Ignore Wide Residue Command Complete Message Parity Error Disconnect Message Reject Extended Message No Operation – Sy.
27 Specifications Product Specifications Altitude Operating 0 to 3048 m (0 to 10,000 ft.) Vibration Operating Swept Sine 5 to 500 Hz *0.25 G Peak 1 Octave/min.
28 Temperature and Humidity Range Temperature Operating 5˚C to 40˚C ( ∆ T<10˚C/h) (41˚F to 104˚F ( ∆ T<18˚F/h)) Non-operating (mech.) – 40˚C to 70˚C ( ∆ T<20˚C/h) (– 40˚F .
29 Sony Contacts For further information, please contact the appropriate Sony location listed below: Sony Electronics Inc., Tape Storage Solutions (USA) URL: http://www.
30 Sony Brasil Ltda. Rua Inocéncio Tobias, 125, Barra Funda São Paulo-SP, Brasil 01144-000 TEL: (55) 11-2196-9000 FAX: (55) 11-2196-9186 URL: http://www.sonybrasil.com.br Sony Australia Limited 33-39 Talavera Rd. NORTH RYDE, NSW 2113 TEL: 1300-13-7669 FAX: 02-9870-5864 e-mail: CIC-customerissues@ap.
.
Printed in U.S.A..
An important point after buying a device Sony SDX-700C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony SDX-700C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony SDX-700C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony SDX-700C you will learn all the available features of the product, as well as information on its operation. The information that you get Sony SDX-700C will certainly help you make a decision on the purchase.
If you already are a holder of Sony SDX-700C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony SDX-700C.
However, one of the most important roles played by the user manual is to help in solving problems with Sony SDX-700C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony SDX-700C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
