Instruction/ maintenance manual of the product DCR-TRV6E Sony
Go to page of 220
3-059-593- 13 (1) © 2000 Sony Corporation Operating Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference.
2 English W elcome! Congratulations on your purchase of this Sony Digital Handycam camcorder. With your Digital Handycam, you can capture life’s precious moments with superior picture and sound quality. Your Digital Handycam is loaded with advanced features, but at the same time it is very easy to use.
3 English T able of contents Checking supplied accessories .............................. 5 Quick Start Guide ............................................. 6 Getting started Using this manual .................................................. 10 Step 1 Preparing the power supply .
4 Русский Ог лавление Пpовepкa пpилaгaeмыx пpинaдлeжноcтeй ........ 5 Pyководcтво по быcтpомy зaпycкy ................. 8 Подготовкa к экcплyaтaции Иcпользовaниe дaнного pyководcтвa .
Getting started Подготовкa к экcплyaтaции 5 Checking supplied accessories Make sure that the following accessories are supplied with your camcorder.
6 Quick Start Guide English Quick Start Guide This chapter introduces you to the basic features of your camcorder. See the page in parentheses “( )” for more information. Open the DC IN jack cover. Connect the plug with its v mark facing lens side.
7 Quick Start Guide Recording a picture (p. 21) Viewfinder When the LCD panel is closed, use the viewfinder placing your eye against its eyecup. Monitoring the playback picture on the LCD screen (p. 36) NOTE Do not pick up your camcorder by holding the viewfinder or the LCD panel.
8 Pyководcтво по быcтpомy зaпycкy Pyccкий Pyк ово дcтво по быcтpомy зaпy cкy B дaнной глaвe пpивeдeны оcновныe фyнкции Baшeй видeокaмepы. Болee подpобнyю инфоpмaцию cм.
9 Pyководcтво по быcтpомy зaпycкy Зaпиcь изобpaжeния (cтp. 21) Контpоль воcпpоизводимого изобpaжeния нa экpaнe ЖКД (cтp. 36) ПPИMEЧAHИE He поднимaйтe видeокaмepy зa видоиcкaтeль или пaнeль ЖКД.
10 — Getting started — Using this manual The instructions in this manual are for the three models listed in the table below. Before you start reading this manual and operating your camcorder, check the model number by looking at the bottom of your camcorder.
Getting started Подготовкa к экcплyaтaции 11 Using this manual Иcпользовaниe дaнного pyководcтвa Note on Cassette Memory Your camcorder is based on the DV format. You can only use mini DV cassettes with your camcorder.
12 Using this manual Note on TV colour systems TV colour systems differ from country to country. To view your recordings on a TV, you need a PAL system-based TV. Copyright precautions Television programmes, films, video tapes, and other materials may be copyrighted.
Getting started Подготовкa к экcплyaтaции 13 Installing the battery pack Install the battery pack to use your camcorder outdoors. ( 1 ) Lift up the viewfinder.
14 Step 1 Preparing the power supply Charging the battery pack Use the battery pack after charging it for your camcorder. Your camcorder operates only with the “InfoLITHIUM” battery pack (M series). ( 1 ) Open the DC IN jack cover, pulling the cover out a little and rotating.
Getting started Подготовкa к экcплyaтaции 15 After charging the battery pack Disconnect the AC power adaptor from the DC IN jack on your camcorder. Notes • Prevent metallic objects from coming into contact with the metal parts of the DC plug of the AC power adaptor.
16 Charging time/ Bpeмя зapядки Battery pack/ Full charge (Normal charge)/ Бaтapeйный блок Полнaя зapядкa (ноpмaльнaя зapядкa) NP-FM50 (supplied)/ 150 (90) (вxо.
Getting started Подготовкa к экcплyaтaции 17 Approximate number of minutes when you use a fully charged battery Numbers in parentheses “( )” indicate the time using a normally charged battery. * Approximate continuous recording time at 25°C (77°F).
18 What is ”InfoLITHIUM”? The “InfoLITHIUM” is a lithium ion battery pack which can exchange data such as battery consumption with compatible electronic equipment. This unit is compatible with the “InfoLITHIUM” battery pack (M series). Your camcorder operates only with the “InfoLITHIUM” battery.
Getting started Подготовкa к экcплyaтaции 19 Connecting to the mains When you use your camcorder for a long time, we recommend that you power it from the mains using the AC power adaptor. ( 1 ) Open the DC IN jack cover, pulling the cover out a little and rotating it.
20 ( 1 ) Install the power source. ( 2 ) Slide OPEN/EJECT in the direction of the arrow and open the lid. The cassette compartment automatically lifts up and opens. ( 3 ) Push the middle portion of the back of the cassette to insert. Insert the cassette in a straight line deeply into the cassette compartment with the window facing out.
Recording – Basics Зaпиcь - Ocновныe положeния 21 VCR OFF ( CHG ) MEMORY CAMERA POWER 2 4 1 3 5 0:00:01 40 min REC — Recording – Basics — Recording a pictur e Your camcorder automatically focuses for you. ( 1 ) Remove the lens cap by pressing both knobs on its sides and attatch the lens cap to the grip strap.
22 Note Fasten the grip strap firmly. Note on recording mode Your camcorder records and plays back in the SP (standard play) mode and in the LP (long play) mode. Select SP or LP in the menu settings. In the LP mode, you can record 1.5 times as long as in the SP mode.
Recording – Basics Зaпиcь - Ocновныe положeния 23 When you record in the SP and LP modes on one tape or you record some scenes in the LP mode The playback picture may be distorted or the time code may not be written properly between scenes.
24 LCD BRIGHT Recording a picture Picture in the mirror mode The picture on the LCD is a mirror-image. However, the picture will be normal when recorded. During recording in the mirror mode ZERO SET MEMORY on the Remote Commander does not work. Indicators in the mirror mode The STBY indicator appears as Xz and REC as z .
Recording – Basics Зaпиcь - Ocновныe положeния 25 Adjusting the viewfinder If you record pictures with the LCD panel closed, check the picture with the viewfinder. Adjust the viewfinder lens to your eyesight so that the indicators in the viewfinder come into sharp focus.
26 Recording a picture Attaching the supplied lens hood (DCR-TRV20E only) To record fine pictures under strong light, we recommend attaching the lens hood.
Recording – Basics Зaпиcь - Ocновныe положeния 27 T W Using the zoom feature Move the power zoom lever a little for a slower zoom. Move it further for a faster zoom. Using the zoom function sparingly results in better-looking recordings.
28 Recording a picture Запись изображения When you shoot close to a subject If you cannot get a sharp focus, move the power zoom lever to the “W” side until the focus is sharp.
Recording – Basics Зaпиcь - Ocновныe положeния 29 Recording a picture Запись изображения Индикaтоpы, отобpaжaeмыe в peжимe зaпиcи Индикaтоpы нe зaпиcывaютcя нa лeнтy. Indicators displayed in the recording mode The indicators are not recorded on tapes.
30 Shooting backlit subjects (BACK LIGHT) When you shoot a subject with the light source behind the subject or a subject with a light background, use the backlight function. In the standby, recording or memory mode, press BACK LIGHT. The . indicator appears in the viewfinder or on the LCD screen.
Recording – Basics Зaпиcь - Ocновныe положeния 31 Shooting in the dark (NightShot/Super NightShot) The NightShot function enables you to shoot a subject in a dark place. For example, you can satisfactorily record the environment of nocturnal animals for observation when you use this function.
32 Recording a picture Notes • Do not use the NightShot function in bright places (ex. outdoors in the daytime). This may cause your camcorder to malfunction. • When you keep NIGHTSHOT set to ON in normal recording, the picture may be recorded in incorrect or unnatural colours.
Recording – Basics Зaпиcь - Ocновныe положeния 33 Recording a picture Self-timer recording You can make a recording with the self-timer. This mode is useful when you want to record yourself. ( 1 ) Press SELFTIMER in the standby mode.
34 Checking the recor ding – END SEARCH / EDITSEARCH / Rec Review You can use these buttons to check the recorded picture or shoot so that the transition between the last recorded scene and the next scene you record is smooth. END SEARCH You can go to the end of the recorded section after you record.
Recording – Basics Зaпиcь - Ocновныe положeния 35 Checking the recording – END SEARCH / EDITSEARCH / Rec Review Rec Review You can check the last recorded section. Press the – 7 side of EDITSEARCH momentarily in the standby mode.
36 — Playback – Basics — Playing back a tape You can monitor the playback picture on the LCD screen. If you close the LCD panel, you can monitor the playback picture in the viewfinder. You can control playback using the Remote Commander supplied with your camcorder.
Playback – Basics Bоcпpоизвeдeниe - Ocновныe положeния 37 Playing back a tape To display the screen indicators – Display function Press DISPLAY on your camcorder or the Remote Commander supplied with your camcorder. The indicators appear on the LCD screen.
38 Playing back a tape Not to display various settings Set DATA CODE to DATE in the menu settings (p. 116). The display changes as follows: date/time t no indicator Recording data Recording data is your camcorder’s information when you have recorded.
Playback – Basics Bоcпpоизвeдeниe - Ocновныe положeния 39 Various playback modes To operate control buttons, set the POWER switch to VCR. To view a still picture (playback pause) Press X during playback. To resume playback, press X or N .
40 Playing back a tape To view the picture at double speed Press × 2 on the Remote Commander during playback. For double speed playback in the reverse direction, press , then press × 2 on the Remote Commander. To resume normal playback, press N . To view the picture frame-by-frame Press C on the Remote Commander in the playback pause mode.
Playback – Basics Bоcпpоизвeдeниe - Ocновныe положeния 41 S VIDEO S VIDEO VIDEO AUDIO IN AUDIO/VIDEO V iewing the recor ding on TV Connect your camcorder to your TV or VCR with the A/V connecting cable supplied with your camcorder to watch the playback picture on the TV screen.
42 If your TV or VCR is a monaural type Connect the yellow plug of the A/V connecting cable to the video input jack and the white or the red plug to the audio input jack on the VCR or the TV. If you connect the white plug, the sound is L (left) signal.
Playback – Basics Bоcпpоизвeдeниe - Ocновныe положeния 43 Viewing the recording on TV Using the AV cordless IR receiver Once you connect the AV cordless IR receiver (not supplied) to your TV or VCR, you can easily view the picture on your TV.
44 If you turn the power off The super laser link function turns off automatically. If you use a Sony TV • You can turn on the TV automatically when you press SUPER LASER LINK. To do so, make sure you: – Turn the TV’s main switch on. – Set AUTO TV ON to ON in the menu settings.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 45 You can record a still picture, for example, a photograph or drawing.
46 Notes • During tape photo recording, you cannot change the mode or setting. • When recording a still picture, do not shake your camcorder. The picture may fluctuate.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 47 Self-timer tape photo recording You can make a tape photo recording with the self-timer. This mode is useful when you want to record yourself. ( 1 ) Set the POWER switch to CAMERA.
48 LINE IN VIDEO S VIDEO AUDIO/VIDEO S VIDEO Printing the still picture You can print a still picture by using the video printer (not supplied). Connect the video printer using the A/V connecting cable supplied with your camcorder. Connect it to the AUDIO/VIDEO jack and connect the yellow plug of the cable to the video input of the video printer.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 49 Adjusting the white balance manually You can manually adjust and set the white balance. This adjustment makes white subjects look white and allows more natural colour balance.
50 If the picture is being taken in a studio lit by TV lighting We recommend you to record in the n indoor mode. When you record under fluorescent lighting Use the automatic white balance or hold mode. Your camcorder may not adjust the white balance correctly in the n indoor mode.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 51 You can record a 16:9 wide picture to watch on the 16:9 wide-screen TV (16:9WIDE).
52 Using the wide mode In the wide mode, you cannot select the following functions: – Old movie – Bounce (DCR-TRV6E/TRV11E only) During recording You cannot select or cancel the wide mode. When you cancel the wide mode, set your camcorder to the standby mode and then set 16:9WIDE to OFF in the menu settings.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 53 You can fade in or out to give your recording a professional appearance.
54 Using the fader function ( 1 ) When fading in [ a ] In the standby mode, press FADER until the desired fader indicator flashes. When fading out [ b ] In the recording mode, press FADER until the desired fader indicator flashes. The indicator changes as follows: FADER t M.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 55 Note You cannot use the following functions while using the fader function.
56 You can digitally process images to obtain special effects like those in films or on the TV. NEG. ART [ a ] : The colour and brightness of the picture is reversed. SEPIA : The picture is sepia. B&W : The picture is monochrome (black-and-white).
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 57 Using special effects – Picture effect ( 1 ) In the standby or recording mode, select P EFFECT in in the menu settings. (p. 116) ( 2 ) Select the desired picture effect mode in the menu settings.
58 Using special ef fects – Digital ef fect You can add special effects to recorded pictures using the various digital functions. The sound is recorded normally. STILL You can record a still picture so that it is superimposed on a moving picture. FLASH (FLASH MOTION) You can record still pictures successively at constant intervals.
Advanced Recording Operations Уcовepшeнcтвовaнныe опepaции cъeмки 59 Using special effects – Digital effect ( 1 ) In the standby or recording mode, press DIGITAL EFFECT. The digital effect indicator appears. ( 2 ) Turn the SEL/PUSH EXEC dial to select the desired digital effect mode.
60 Using special effects – Digital effect To cancel the digital effect function Press DIGITAL EFFECT again. Notes • The following functions do not work during digital effect mode: – Fader – Lo.
Advanced Recording Operations Усовершенствованные операции съемки 61 Using the PROGRAM AE function You can select PROGRAM AE (Auto Exposure) mode to suit your specific shooting requirements.
62 Using the PROGRAM AE function ( 1 ) In the standby or memory mode, press PROGRAM AE. The PROGRAM AE indicator appears. ( 2 ) Turn the SEL/PUSH EXEC dial to select the desired PROGRAM AE mode. The indicator changes as follows: y y y y y y To cancel the PROGRAM AE function Press PROGRAM AE again.
Advanced Recording Operations Усовершенствованные операции съемки 63 Notes • In the spotlight, sports lesson, and beach & ski modes, you cannot take close-ups. This is because your camcorder is set to focus only on subjects in the middle to far distance.
64 You can manually adjust and set the exposure. Adjust the exposure manually in the following cases: • The subject is backlit • Bright subject and dark background • To record dark pictures (e.g. night scenes) faithfully ( 1 ) In the standby, recording or memory mode, press EXPOSURE.
Advanced Recording Operations Усовершенствованные операции съемки 65 Focusing manually You can gain better results by manually adjusting the focus in the following cas.
66 To return to the autofocus mode Set FOCUS to AUTO. To record distant subjects When you press FOCUS down to INFINITY, the lens focuses on and indicator appears. When you release FOCUS, your camcorder returns to the manual focus mode. Use this mode when your camcorder focuses on near objects even though you are trying to shoot a distant object.
Advanced Playback Operations Усовершенствованные операции воспроизведения 67 — Advanced Playback Operations — Playing back a tape with pictur e effects During playback, you can process a scene using the picture effect functions: NEG.
68 2 3 1 STILL STILL DIGIT AL EFFECT During playback, you can process a scene using the digital effect functions: STILL, FLASH, LUMI., and TRAIL. ( 1 ) In the playback or playback pause mode, press DIGITAL EFFECT and turn the SEL/ PUSH EXEC dial until the desired digital effect indicator (STILL, FLASH, LUMI.
Advanced Playback Operations Усовершенствованные операции воспроизведения 69 Notes • You cannot process externally input scenes using the digital effect function.
70 Enlarging images r ecorded on tapes – PB ZOOM You can enlarge still and moving playback pictures. You can also dub the enlarged pictures to tapes or copy to “Memory Stick”s. ( 1 ) In the playback or playback pause mode, press PB ZOOM on your camcorder.
Advanced Playback Operations Усовершенствованные операции воспроизведения 71 Note You cannot process externally input scenes using the PB ZOOM function with your camcorder.
72 Quickly locating a scene using the zer o set memory function Your camcorder goes forward or backward to automatically stop at a desired scene having a tape counter value of “0:00:00”. You can do this with the Remote Commander. ( 1 ) In the playback mode, press DISPLAY.
Advanced Playback Operations Усовершенствованные операции воспроизведения 73 Sear ching the boundaries of r ecor ded tape by title – Title sear ch If you use a tape with cassette memory, you can search for the boundaries of recorded tape by title ( Title search ).
74 If you use a tape without cassette memory You cannot search or superimpose a title. In the mark • The bar in the mark indicates the present point on the tape. • The mark in the indicates the actual point you are trying to search. If a tape has a blank portion between recorded portions The title search function may not work correctly.
Advanced Playback Operations Усовершенствованные операции воспроизведения 75 You can automatically search for the point where the recording date changes and start playback from that point (Date search) . Use a tape with cassette memory for convenience.
76 To stop searching Press x . Note If one day’s recording is less than two minutes, your camcorder may not accurately find the point where the recording date changes. In the mark • The bar in the mark indicates the present point on the tape. • The mark in the indicates the actual point you are trying to search.
Advanced Playback Operations Усовершенствованные операции воспроизведения 77 You can search for a still picture you have recorded on a mini DV tape (photo search) .
78 Searching for a photo – Photo search/Photo scan Поиcк фото – Фотопоиcк/ Фотоcкaниpовaниe If a tape has a blank portion between recorded portions The photo search function may not work correctly. The available number of photos that can be searched using the cassette memory The available number is up to 12 photos.
Advanced Playback Operations Усовершенствованные операции воспроизведения 79 Scanning photo ( 1 ) Set the POWER switch to VCR. ( 2 ) Press SEARCH MODE on the Remote Commander repeatedly, until the PHOTO SCAN indicator appears.
80 Using the A/V connecting cable Connect your camcorder to the VCR using the A/V connecting cable supplied with your camcorder. Set the input selector on the VCR to LINE, if available. ( 1 ) Insert a blank tape (or a tape you want to record over) into the VCR, and insert the recorded tape into your camcorder.
Editing Монтаж 81 Dubbing a tape Before a dubbing Set DISPLAY to LCD in the menu settings. (Default setting is LCD.) Be sure to clear the indicators from the screen If they are displayed, press .
82 Using the i.LINK cable (DV connecting cable) Simply connect the i.LINK cable (DV connecting cable) (not supplied) to DV IN/OUT and to DV IN of the DV products. With digital-to-digital connection, video and audio signals are transmitted in digital form for high-quality editing.
Editing Монтаж 83 Dubbing a tape Пepeзaпиcь лeнты You can connect one VCR only using the i.LINK cable (DV connecting cable). The following functions do not work during digital editing: – Digital effect – PB ZOOM – Picture effect If you record playback pause picture with the DV IN/OUT jack The recorded picture becomes rough.
84 You can duplicate selected scenes (programmes) for editing onto a tape without operating the VCR. Scenes can be selected by frame. Before operating the Digital program editing Step 1 Connecting the VCR. (p. 80, 82) Step 2 Setting the VCR for operation.
Editing Монтаж 85 Step 2: Setting the VCR for operation – Using the infrared rays emitter To edit using the VCR, send the control signal by infrared ray to the remote sensor on the VCR. When you connect using an AV connecting cable, follow the procedures below.
86 About the IR SETUP code The IR SETUP code is stored in the memory of your camcorder. Be sure to set the correct code, depending on your VCR. Code number 1 is preset at the factory.
Editing Монтаж 87 Setting the modes to cancel the recording pause on the VCR ( 1 ) Turn the SEL/PUSH EXEC dial to select PAUSEMODE, then press the dial. ( 2 ) Turn the SEL/PUSH EXEC dial to select the mode to cancel recording pause on the VCR, then press the dial.
88 Dubbing only desired scenes – Digital program editing Confirming the VCR operation ( 1 ) Insert a recordable tape into the VCR, then set to recording pause. ( 2 ) Turn the SEL/PUSH EXEC dial to select IR TEST, then press the dial. ( 3 ) Turn the SEL/PUSH EXEC dial to select EXECUTE, then press the dial.
Editing Монтаж 89 Dubbing only desired scenes – Digital program editing Step 2: Setting the VCR for operation – Using the i.LINK cable (DV connecting cable) When you connect using i.LINK cable (DV connecting cable) (not supplied), follow the procedures below.
90 Step 3: Adjusting the synchronicity of the VCR You can adjust the synchronicity of your camcorder and the VCR. Have a pen and paper ready for notes. ( 1 ) Set the POWER swtich to VCR on your camcorder. ( 2 ) Insert a blank tape (or a tape you want to record over) into the VCR, then set to recording pause.
Editing Монтаж 91 Dubbing only desired scenes – Digital program editing ( 7 ) Turn the SEL/PUSH EXEC dial to select “CUT-IN”, then press the dial. ( 8 ) Turn the SEL/PUSH EXEC dial to select the average numerical value of IN, then press the dial.
92 Dubbing only desired scenes – Digital program editing Notes • If you start recording from the very beginning of the tape, the first few seconds of the tape may not record properly. Be sure to allow about 10 seconds’ lead before starting the recording.
Editing Монтаж 93 Operation 1: Making the Programme ( 1 ) Insert the tape for playback into your camcorder, and insert a tape for recording into the VCR. ( 2 ) Press MENU to display the menu. ( 3 ) Turn the SEL/PUSH EXEC dial to select , then press the dial.
94 Dubbing only desired scenes – Digital program editing Erasing the programme you have set Erase OUT first and then IN from of the last programme. ( 1 ) Turn the SEL/PUSH EXEC dial to select UNDO, then press the dial. ( 2 ) Turn the SEL/PUSH EXEC dial to select EXECUTE, then press the dial.
Editing Монтаж 95 Dubbing only desired scenes – Digital program editing Operation 2: Performing a Digital program editing (Dubbing a tape) Make sure your camcorder and VCR are connected, and that the VCR is set to recording pause. When you use an i.
96 Using with analog video unit and PC – Signal convert function You can convert analog video signals into digital video signals via your camcorder connected to a PC and analog video unit. Analog video signals t Digital video signals You can capture images and sound from an analog video unit connecting a PC which has the i.
Editing Монтаж 97 VIDEO AUDIO OUT AUDIO/VIDEO S VIDEO TV REC 4 PAUSE S VIDEO Recor ding video or TV programmes Using the A/V connecting cable You can record a tape from another VCR or a TV programme from a TV that has video/audio outputs. Use your camcorder as a recorder.
98 Recording video or TV programmes When you have finished dubbing a tape Press x on both your camcorder and the VCR. Using the Remote Commander (DCR-TRV11E/TRV20E only) In step 4, press z REC and MARK simultaneously, then immediately press X . And in step 6, press X at the scene where you want to start recording from.
Editing Монтаж 99 Recording video or TV programmes Using the i.LINK cable (DV connecting cable) Simply connect the i.LINK cable (DV connecting cable) (not supplied) to DV IN/OUT and to DV IN/OUT of the DV products. With digital-to- digital connection, video and audio signals are transmitted in digital form for high-quality editing.
100 Recording video or TV programmes When you have finished dubbing a tape Press x on both your camcorder and the VCR. Using the Remote Commander (DCR-TRV11E/TRV20E only) In step 4, press z REC and MARK simultaneously, then immediately press X . And in step 6, press X at the scene where you want to start recording from.
Editing Монтаж 101 Inserting a scene a from VCR – Insert editing You can insert a new scene from a VCR onto your originally recorded tape by specifying the insert start and end points. Use the Remote Commander for this operation. Connections are the same as on page 97 or 99.
102 Inserting a scene a from VCR – Insert editing ( 1 ) Set the POWER switch to VCR on your camcorder. ( 2 ) On the connected VCR, locate just before the insert start point [a] , then press X to set the VCR to the playback pause mode. ( 3 ) On your camcorder, locate the insert end point [c] by pressing m or M .
Editing Монтаж 103 Inserting a scene a from VCR – Insert editing Using the Remote Commander (DCR-TRV11E/TRV20E only) In step 5, press z REC and MARK simultaneously, then immediately press X . And in step 6, press X at the scene where you want to start recording from.
104 You can record an audio sound to add to the original sound on a tape by connecting audio equipment or a microphone. If you connect the audio equipment, you can add sound to your recorded tape by specifying starting and ending points. The original sound will not be erased.
Editing Монтаж 105 Dubbing with the AUDIO/VIDEO jack Dubbing with the built-in microphones No connection is necessary. Notes • While audio dubbing, the sound does not output from the speaker.
106 Audio dubbing Ayдиопepeзaпиcь Adding an audio sound on a recorded tape ( 1 ) Insert your recorded tape into your camcorder. ( 2 ) Set the POWER switch to VCR on your camcorder. ( 3 ) Locate the recording start point by pressing N . Then press X at the point where you want to start recording to set your camcorder to playback pause mode.
Editing Монтаж 107 Audio dubbing Five minutes after when you disconnect the power source or remove the battery pack, the setting of AUDIO MIX returns to the original sound (ST1) only. The factory setting is original sound only. Notes • New sound cannot be recorded on a tape already recorded in the 16-bit mode (32 kHz, 44.
108 Superimposing a title If you use a tape with cassette memory, you can superimpose the title while recording or after recording. When you play back the tape, the title is displayed for five seconds from the point where you superimposed it. You can select one of eight preset titles and two custom titles (p.
Editing Монтаж 109 Superimposing a title Haложeниe титpa If you set the write-protect tab of the tape to lock You cannot superimpose or erase the title. Slide the write-protect tab to release the write protection. To use the custom title If you want to use the custom title, select in step 2.
110 Superimposing a title If the tape has too many index signals You may not be able to superimpose a title because the memory is full. In this case, delete data you do not need. Not to display titles Set TITLE DSPL to OFF in the menu settings (p. 116).
Editing Монтаж 111 Erasing a title ( 1 ) Set the POWER switch to VCR. ( 2 ) Press MENU to display the menu. ( 3 ) Turn the SEL/PUSH EXEC dial to select , then press the dial. ( 4 ) Turn the SEL/PUSH EXEC dial to select TITLEERASE, then press the dial.
112 Making your own titles You can make up to two titles and store them in the cassette memory. Each title can have up to 20 characters. ( 1 ) Press TITLE in the standby or VCR mode.
Editing Монтаж 113 To change a title you have stored In step 3, select CUSTOM1 or CUSTOM2, depending on which title you want to change, then press the SEL/PUSH EXEC dial. Turn the SEL/PUSH EXEC dial to select [ C ], then press the dial to delete the title.
114 Labelling a cassette If you use a tape with cassette memory, you can label a cassette. The label can consist of up to 10 characters and is stored in cassette memory. When you insert the labelled cassette and turn the power on, the label is displayed for about five seconds.
Editing Монтаж 115 To erase a character In step 6 turn the SEL/PUSH EXEC dial to select [ C ], then press the dial. The last character is erased. To change the label you have made Insert the cassette to change the label, and operate in the same way to make a new label.
116 — Customizing Your Camcorder — Changing the menu settings To change the mode settings in the menu settings, select the menu items with the SEL/ PUSH EXEC dial. The factory settings can be partially changed. First, select the icon, then the menu item and then the mode.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 117 Changing the menu settings To make the menu display disappear Press MENU.
118 Changing the menu settings Note on the playback of the NTSC tapes When you play back a tape on a Multi System TV, select the best mode while viewing the picture on the TV. Notes on LCD B.L. • When you select “BRIGHT”, battery life is reduced by about 10 percent during recording.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 119 Changing the menu settings *1) DCR-TRV11E/TRV20E only *2) DCR-TRV20E onl.
120 Changing the menu settings Notes on the LP mode • When you record a tape in the LP mode on your camcorder, we recommend playing the tape on your camcorder. When you play back the tape on other camcorders or VCRs, noise may occur in pictures or sound.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 121 Changing the menu settings Icon/item q REMAIN DATA CODE CLOCK SET AUTO TV ON TV INPUT LTR SIZE DEMO MODE Notes on DEMO MODE • You cannot select DEMO MODE when a cassette is inserted in your camcorder.
122 Changing the MENU settings Icon/item WORLD TIME BEEP COMMANDER DISPLAY REC LAMP VIDEO EDIT EDIT SET Note If you press DISPLAY with DISPLAY set to V-OUT/LCD in the menu settings, the picture from a TV or VCR will not appear on the LCD screen even when your camcorder is connected to outputs on the TV or VCR.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 123 Pyccкий Bыбоp ycтaновок peжимa по кaждомy пyнктy z зaводcкaя ycтaновкa. Пyнкты мeню отличaютcя в зaвиcимоcти от положeния пepeключaтeля POWER.
124 Изменение установок MENU Пpимeчaниe по воcпpоизвeдeнию лeнт NTSC Пpи воcпpоизвeдeнии лeнты нa мyльтиcиcтeмном тeлeвизоpe выбepитe нaилyчший peжим во вpeмя пpоcмотpa изобpaжeния нa экpaнe тeлeвизоpa.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 125 Изменение установок MENU Пиктограмма/пун.
126 Изменение установок MENU Пpимeчaния по peжимy LP • Ecли зaпиcь лeнты выполнялacь нa Baшeй видeокaмepe в peжимe LP, ee peкомeндyeтcя воcпpоизводить нa этой видeокaмepe.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 127 Изменение установок MENU Пиктограмма/пун.
128 Изменение установок MENU Пиктограмма/пункт WORLD TIME BEEP COMMANDER DISPLAY REC LAMP VIDEO EDIT EDIT SET Режим z MELODY NORMAL OFF z ON OFF z LCD V-OUT/LCD z ON OFF Haзнaчeниe Для ycтaновки чacов нa мecтноe вpeмя.
Customizing Your Camcorder Выполнение индивидуальных установок на видеокамере 129 Resetting the date and time The clock is set at the factory to Sydney time for Australia and New Zealand models, to Tokyo time for the models sold in Japan, and to Hong Kong time for other models.
130 Resetting the date and time The year changes as follows: If you do not set the date and time “– –:– –:– –” is recorded on the data code of the tape and the “Memory Stick” (DCR-TRV11E/ TRV20E only.) Note on the time indicator The internal clock of your camcorder operates on a 24-hour cycle.
“Memory Stick” operations Oпepaции c “Memory Stick” 131 – DCR-TRV11E/TRV20E only You can record and play back still images on a “Memory Stick” supplied with your camcorder. You can easily play back, record or delete still images. You can exchange image data with other equipment such as a personal computer etc.
132 Using a “Memory Stick” –introduction • Do not let “Memory Stick”s get wet. • Do not use or keep “Memory Stick”s in locations that are: – Extremely hot such as in a car parked in the sun or under the scorching sun. – Under direct sunlight.
“Memory Stick” operations Oпepaции c “Memory Stick” 133 Using a “Memory Stick” –introduction Inserting a “Memory Stick” ( 1 ) Slide MEMORY OPEN in the direction of the arrow. The “Memory Stick” compartment opens. ( 2 ) Insert a “Memory Stick” in as far as it can go with its rounded corner facing up.
134 Using a “Memory Stick” –introduction Иcпользовaниe “Memory Stick” – Bвeдeниe Selecting image quality mode You can select image quality mode in still picture recording. Image quality is set to SUPER FINE mode at the factory.
“Memory Stick” operations Oпepaции c “Memory Stick” 135 Using a “Memory Stick” –introduction Иcпользовaниe “Memory Stick” – Bвeдeниe Image quality mode Setting Meaning SUPER FINE This is the highest image (SFN) quality in your (DCR-TRV20E camcorder.
136 Using a “Memory Stick” –introduction Иcпользовaниe “Memory Stick” – Bвeдeниe Selecting image size – DCR-TRV20E only You can select either one of two image sizes: 1152 × 864 or 640 × 480. (In VCR mode, you can select only 640 × 480.
“Memory Stick” operations Oпepaции c “Memory Stick” 137 Using a “Memory Stick” –introduction Иcпользовaниe “Memory Stick” – Bвeдeниe Image size settings/ Уcтaновки paзмepов изобpaжeния Setting/ Уcтaновкa 1152 × 864 640 × 480 Meaning/ Haзнaчeниe Records 1152 × 864 still images.
138 Recor ding still images on “Memory Stick”s – Memory Photo r ecor ding – DCR-TRV11E/TRV20E only You can record still pictures on “Memory Stick”s. Before operation Insert a “Memory Stick” into your camcorder. ( 1 ) Set the POWER switch to MEMORY.
“Memory Stick” operations Oпepaции c “Memory Stick” 139 Recording still images on “Memory Stick”s – Memory Photo recording When the POWER switch is set to MEMORY The following functi.
140 While pressing down PHOTO, your camcorder continuously record maximum number of still pictures depending on the image size. When you stop pressing, the recording stops.
“Memory Stick” operations Oпepaции c “Memory Stick” 141 Recording still images on “Memory Stick”s – Memory Photo recording ( 1 ) Set the POWER switch to MEMORY. Make sure that the LOCK switch is set to the left (unlock) position. ( 2 ) Press MENU to display the menu.
142 Recording still images on “Memory Stick”s – Memory Photo recording Continuous shooting settings Setting Meaning (indicator on the screen) OFF Your camcorder shoots one image at a time. (no indicator) ON Your camcorder shoots up to 16 (DCR-TRV20E still images at about 0.
“Memory Stick” operations Oпepaции c “Memory Stick” 143 Recording still images on “Memory Stick”s – Memory Photo recording Зaпиcь нeподвижныx изобpaжeний нa “.
144 Superimposing a still pictur e in a “Memory Stick” on a moving pictur e – MEMOR Y MIX – DCR-TRV11E/TRV20E only You can superimpose a still picture you have recorded on a “Memory Stick” on the top of the moving picture you are recording.
“Memory Stick” operations Oпepaции c “Memory Stick” 145 M. CHROM Still picture/ Moving picture/ Heподвижноe Подвижноe изобpaжeниe изобpaжeниe + b M. LUMI Still picture/ Moving picture/ Heподвижноe Подвижноe изобpaжeниe изобpaжeниe + b C.
146 1 2 4 5 6 1 M. CHROM M. LUMI M. LUMI M. LUMI III¥¥¥¥ I¥¥¥¥¥¥ 3 MEMOR Y MIX VCR OFF ( CHG ) MEMORY CAMERA POWER Superimposing a still picture in a “Memory Stick” on a moving picture – MEMORY MIX ( 1 ) Set the POWER switch to CAMERA.
“Memory Stick” operations Oпepaции c “Memory Stick” 147 Superimposing a still picture in a “Memory Stick” on a moving picture – MEMORY MIX Items to adjust M. CHROM The colour (blue) scheme of the area in the still picture which is to be swapped with a moving picture M.
148 During recording You cannot change the mode setting. The “Memory Stick” supplied with your camcorder has stored 20 images – For M.CHROM : 18 images (such as a frame) 100-0001 ~ 100-0018 – For C.
“Memory Stick” operations Oпepaции c “Memory Stick” 149 Recor ding an image from a mini DV tape as a still image – DCR-TRV11E/TRV20E only Your camcorder can read moving picture data recorded on a mini DV tape and record it as a still image on a “Memory Stick”.
150 Image size of still pictures Image size is automatically set to 640 × 480. When the access lamp is lit or flashing Never shake or strike the unit. As well do not turn the power off , eject a “Memory Stick” or remove the battery pack. Otherwise, the image data breakdown may occur.
“Memory Stick” operations Oпepaции c “Memory Stick” 151 Recording an image from a mini DV tape as a still image Зaпиcь изобpaжeния c лeнты мини DV кaк нeподвиж.
152 Copying still images from a mini DV tape – Photo save – DCR-TRV11E/TRV20E only Using the search function, you can automatically take in only still images from mini DV tapes and record them on a “Memory Stick” in sequence. Before operation • Insert a recorded mini DV tape into your camcorder and rewind the tape.
“Memory Stick” operations Oпepaции c “Memory Stick” 153 To stop or end copying Press MENU. When the memory of the “Memory Stick“ is full “MEMORY FULL” appears on the LCD screen or in the viewfinder, and the copying stops. Insert another “Memory Stick” and repeat the procedure from step 2.
154 1 2 1 3 VCR OFF ( CHG ) MEMORY CAMERA POWER PLA Y V iewing a still picture – Memory photo playback Пpоcмотp нeпо движног о изобpaжeния – Bоcпpоизвeдeниe фотоcнимк ов из пaмяти To stop memory photo playback Press MEMORY PLAY again.
“Memory Stick” operations Oпepaции c “Memory Stick” 155 6 / 100 MEMORY PLAY 100-0006 640 Viewing a still picture – Memory photo playback To play back recorded images on a TV screen • Connect your camcorder to the TV with the A/V connecting cable supplied with your camcorder before the operation.
156 1 2 VCR OFF ( CHG ) MEMORY CAMERA POWER INDEX Viewing a still picture – Memory photo playback Пpоcмотp нeподвижного изобpaжeния – Bоcпpоизвeдeниe фотоcнимков из пaмяти Playing back six recorded images at a time (index screen) You can play back six recorded images at a time.
“Memory Stick” operations Oпepaции c “Memory Stick” 157 Viewing a still picture – Memory photo playback Note When displaying the index screen, the number appears above each image. This indicates the order in which images are recorded on the “Memory Stick”.
158 Copying the image r ecorded on “Memory Stick”s to mini DV tapes – DCR-TRV11E/TRV20E only You can copy still images or titles recorded on “Memory Stick” and record them to a mini DV tape. Before operation • Insert mini DV tape for recording into your camcorder.
“Memory Stick” operations Oпepaции c “Memory Stick” 159 Copying the image recorded on “Memory Stick”s to mini DV tapes During copying You cannot operate the following buttons: MEMORY PLAY, MEMORY INDEX, MEMORY DELETE, MEMORY +, MEMORY –, and MEMORY MIX.
160 Enlarging still images recor ded on “Memory Stick”s – Memory PB ZOOM – DCR-TRV11E/TRV20E only You can enlarge still images recorded on a “Memory Stick”. Before operation Insert a “Memory Stick” into your camcorder. ( 1 ) In the memory playback mode, press PB ZOOM on your camcorder.
“Memory Stick” operations Oпepaции c “Memory Stick” 161 Enlarging still images recorded on “Memory Stick”s– Memory PB ZOOM Note You cannot record the images enlarged by the PB ZOOM mode on “Memory Stick”s.
162 – DCR-TRV11E/TRV20E only You can automatically play back images in sequence. This function is useful especially when checking recorded images or during a presentation. Before operation Insert a “Memory Stick” into your camcorder. ( 1 ) Set the POWER switch to MEMORY.
“Memory Stick” operations Операции с “Memory Stick” 163 To stop or end the slide show Press MENU. To pause during a slide show Press MEMORY PLAY. To start the slide show from a particular image Select the desired image using MEMORY +/– buttons before step 2.
164 Preventing accidental erasure – Image pr otection – DCR-TRV11E/TRV20E only To prevent accidental erasure of important images, you can protect selected images. Before operation Insert a “Memory Stick” into your camcorder. ( 1 ) Set the POWER switch to MEMORY or VCR.
“Memory Stick” operations Операции с “Memory Stick” 165 To cancel image protection Select OFF in step 6, then press the SEL/PUSH EXEC dial. Note Formatting erases all information on the “Memory Stick”, including the protected image data.
166 Deleting images 1 3,4 2 VCR OFF ( CHG ) MEMORY CAMERA POWER DELETE 100-0010 [ DELETE ] : DEL [ — ] : CANCEL 89 / 100 DELETE? 640 PLA Y DELETE Удaлeниe изобpaжeний Для отмeны yдaлeния изобpaжeния Haжмитe кнопкy MEMORY – в пyнктe 4.
“Memory Stick” operations Операции с “Memory Stick” 167 Deleting all the images You can delete all the unprotected images in a “Memory Stick”. Before operation Insert a “Memory Stick” into your camcorder. ( 1 ) Set the POWER switch to MEMORY.
168 To cancel deleting all the images in the “Memory Stick” Select RETURN in step 5, then press the SEL/ PUSH EXEC dial. While “DELETING” appears Do not turn the POWER switch or press any buttons.
“Memory Stick” operations Операции с “Memory Stick” 169 Writing a print mark – PRINT MARK Зaпиcь пeчaтныx знaк ов – PRINT MARK – DCR-TRV11E/TRV20E only You can specify the recorded still image to print out. This function is useful for printing out still images later.
170 To cancel writing print marks Select OFF in step 6, then press the SEL/PUSH EXEC dial. If the write-protect tab on the “Memory Stick” is set to LOCK You cannot write print marks on still images.
Additional Information Дополнитeльнaя инфоpмaция 171 — Additional Information — Usable cassettes Selecting cassette types You can use the mini DV cassette only*. You cannot use any other 8 mm, Hi8, Digital8, VHS, VHSC, S-VHS, S-VHSC, Betamax, ED Betamax or DV cassette.
172 When you play back Copyright signal When you play back Using any other video camera recorder, you cannot record on tape that has recorded a copyright control signals for copyright protection of software which is played back on your camcorder.
Additional Information Дополнитeльнaя инфоpмaция 173 Usable cassettes Иcпользyeмыe кacceты Do not affix a label around this border.
174 The DV jack on this unit is an i.LINK-compliant DV input/output jack. This section describes the i.LINK standard and its features. What is i.LINK? i.LINK is a digital serial interface for handling digital video, digital audio and other data in two directions between equipment having the i.
Additional Information Дополнитeльнaя инфоpмaция 175 i.LINK Baud rate i.LINK’s maximum baud rate varies according to the equipment. Three maximum baud rates are defined: S100 (approx. 100Mbps*) S200 (approx. 200Mbps) S400 (approx.
176 English T r oubleshooting If you run into any problem using your camcorder, use the following table to troubleshoot the problem. If the problem persists, disconnect the power source and contact your Sony dealer or local authorized Sony service facility.
Additional Information Дополнитeльнaя инфоpмaция 177 Troubleshooting Picture appears too bright, and the subject does not appear on the LCD screen or in the viewfinder . The picture is r ecorded in incorr ect or unnatural colours. The click of the shutter does not sound.
178 Troubleshooting In the recording and playback modes Symptom Cause and/or Corrective Actions • The battery pack is not installed, or is dead or nearly dead. c Install a charged battery pack. (p. 13, 14) • The AC power adaptor is not connected to the mains.
Additional Information Дополнитeльнaя инфоpмaция 179 Troubleshooting The image cannot be deleted. Y ou cannot format the “Memory Stick”. Deleting all the images cannot be carried out. Y ou cannot write a print mark on the still image.
180 The Remote Commander supplied with your camcorder does not work. Troubleshooting Y ou cannot charge the battery pack. Others Symptom Cause and/or Corrective Actions • The tape has no cassette memory. c Use a tape with cassette memory. (p. 108, 171) • The cassette memory is full.
Additional Information Дополнитeльнaя инфоpмaция 181 Symptom Cause and/or Corrective Actions • Moisture condensation has occurred. c Remove the cassette and leave your camcorder for at least 1 hour to acclimatize. (p. 195) • Some troubles has occurred in your camcorder.
182 English Self-diagnosis display Five-digit display Cause and/or Corrective Actions • You are using a battery pack that is not an “InfoLITHIUM” battery pack. c Use an “InfoLITHIUM” battery pack. (p. 14) • Moisture condensation has occurred.
Additional Information Дополнитeльнaя инфоpмaция 183 C:21:00 100-0001 English W ar ning indicators and messages If indicators and messages appear in the viewfinder, on the LCD screen or in the display window, check the following: See the page in parentheses “( )” for more information.
184 Warning messages • CLOCK SET Reset the date and time (p. 129). • FOR “InfoLITHIUM” Use an “InfoLITHIUM” battery pack (p. 14). BATTERY ONLY • CLEANING CASSETTE The video heads are dirty (p. 196). • FULL The tape cassette memory is full.
Additional Information Дополнитeльнaя инфоpмaция 185 Pyccкий Поиcк и y cтpaнeниe нeиcпpaвноcтeй Ecли y Bac возниклa кaкaя-либо пpоблeмa пp.
186 Поиск и устранение неисправностей Bозможнaя пpичинa Bepоятнaя пpичинa и/или мeтод ycтpaнeния • Комaндa NIGHTSHOT ycтaновлeнa в положeниe ON. c Уcтaновитe ee в положeниe OFF.
Additional Information Дополнитeльнaя инфоpмaция 187 Поиск и устранение неисправностей B peжимax зaпиcи и воcпpоизвeдeния Bозмо.
188 Поиск и устранение неисправностей He paботaeт “Memory Stick” . He выпо лняeтcя зaпиcь. He yдaляeтcя изобpaжeниe . Heвозмо жно отфоpмaтиpовaть “Memory Stick” . He yдaeтcя выпо лнить yдaлeниe вce x изобpaжeний.
Additional Information Дополнитeльнaя инфоpмaция 189 Поиск и устранение неисправностей Пpочee Bозможнaя пpичинa Bepоятнaя пpичинa и/или мeтод ycтpaнeния • Лeнтa нe имeeт кacceтной пaмяти.
190 Bозможнaя пpичинa Bepоятнaя пpичинa и/или мeтод ycтpaнeния • Комaндa COMMANDER ycтaновлeнa в положeниe OFF в ycтaновкax мeню. c Уcтaновитe ee в положeниe ON. (cтp. 116) • Что-то пpeпятcтвyeт пpоxождeнию инфpaкpacныx лyчeй.
Additional Information Дополнитeльнaя инфоpмaция 191 Pyccкий Индикaция caмо диaгноcтики Пятизнaчнaя индикaция Bepоятнaя пpичинa и/.
192 C:21:00 100-0001 Pyccкий Пpeдyпpeждaющиe индикaтоpы и cообщeния Ecли в видоиcкaтeлe, нa экpaнe ЖКД или в окошкe диcплeя появятcя индикaтоpы и cообщeния, пpовepьтe cлeдyющee: Болee подpобнyю инфоpмaцию cм.
Additional Information Дополнитeльнaя инфоpмaция 193 Пpeдyпpeждaющиe cообщeния • CLOCK SET Пepeycтaновитe дaтy и вpeмя (cтp. 129). • FOR “InfoLITHIUM” Иcпользyйтe бaтapeйный блок “InfoLITHIUM” (cтp.
194 Using your camcorder abroad You can use your camcorder in any country or area with the AC power adaptor supplied with your camcorder within 100 V to 240 V AC, 50/60 Hz. Your camcorder is a PAL system based camcorder. If you want to view the playback picture on a TV, it must be a PAL system based TV with AUDIO/VIDEO input jack.
Additional Information Дополнительная информация 195 Maintenance information and pr ecautions Moisture condensation If your camcorder is brought directly from a cold place to a warm place, moisture may condense inside your camcorder, on the surface of the tape, or on the lens.
196 Maintenance information Cleaning the video head To ensure normal recording and clear pictures, clean the video heads. The video head may be dirty when: • mosaic-pattern noise appears on the playback picture. • playback pictures do not move. • playback pictures do not appear.
Additional Information Дополнительная информация 197 Maintenance information and precautions Precautions Camcorder operation • Operate your camcorder on 7.2 V (battery pack) or 8.4 V (AC power adaptor). • For DC or AC operation, use the accessories recommended in this operating instructions.
198 AC power adaptor • Unplug the unit from the mains when you are not using the unit for a long time. To disconnect the mains lead, pull it out by the plug. Never pull the mains lead itself. • Do not operate the unit with a damaged cord or if the unit has been dropped or damaged.
Additional Information Дополнительная информация 199 Maintenance information and precautions Notes on dry batteries To avoid possible damage from battery leakage or corrosion, observe the following: • Be sure to insert the batteries with the + – polarities matched to the + – marks.
200 English Specifications Video camera recorder System Video recording system 2 rotary heads Helical scanning system Audio recording system Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, .
Additional Information Дополнитeльнaя инфоpмaция 201 AC power adaptor Power requirements 100 - 240 V AC, 50/60 Hz Power consumption 23 W Output voltage DC OUT: 8.
202 Pyccкий T exничecкиe x apaктepиcтики Bидeокaмepa Cиcтeмa Cиcтeмa видeозaпиcи 2 вpaщaющиecя головки Cиcтeмa нaклонной мexaничecкой p.
Additional Information Дополнитeльнaя инфоpмaция 203 Bec (пpибл.) DCR-TRV6E: 580 г DCR-TRV11E: 620 г DCR-TRV20E: 680 г только caмa видeокaмepa DCR-TRV6E: 680 г.
204 — Quick Reference — Identifying the parts and contr ols 1 Viewfinder lens adjustment lever (p. 25) 2 Display window (p. 214) 3 OPEN button (p. 21) 4 PROGRAM AE button (p. 61) 5 EXPOSURE button (p. 64) 6 SEL/PUSH EXEC dial (p. 49, 116) This mark indicates that this product is a genuine accessory for Sony video products.
Quick Reference Кpaткий cпpaвочник 205 7 EDITSEARCH buttons (p. 34) 8 Intelligent accessory shoe (p. 104, 211) 9 Focus ring (p. 65) 0 FOCUS switch (p. 65) qa Camera recording lamp (p. 21) qs Microphone qd Infrared rays emitter (p. 31, 43, 87) qf Remote sensor qg SUPER LASER LINK button (p.
206 Identifying the parts and controls wa MEMORY PLAY button (DCR-TRV11E/TRV20E only) (p. 154) ws MEMORY +/– buttons (DCR-TRV11E/TRV20E only) (p. 146, 154) wd LCD screen (p. 23) wf Speaker wg MEMORY INDEX button (DCR-TRV11E/TRV20E only) (p. 156) wh MEMORY DELETE button (DCR-TRV11E/TRV20E only) (p.
Quick Reference Кpaткий cпpaвочник 207 Identifying the parts and controls wk DISPLAY button (p. 37) wl DIGITAL EFFECT button (p. 58, 68) e; PB ZOOM button (p. 70, 160) ea RESET button (p. 181) es END SEARCH button (p. 34) ed MENU button (p.
208 r; ra rs rd ek ej el ej PHOTO button (p. 45, 138) ek BATT release button (p. 13) el Hooks for shoulder strap r; Power zoom lever (p. 27) ra NIGHTSHOT switch (p. 31) rs SUPER NIGHTSHOT button (p. 31) rd MEMORY RELEASE button (DCR-TRV11E/TRV20E only) (p.
Quick Reference Кpaткий cпpaвочник 209 Identifying the parts and controls rf Access lamp (DCR-TRV11E/TRV20E only) (p. 133) rg MEMORY OPEN button (DCR-TRV11E/TRV20E only) (p. 133) rh LOCK switch (DCR-TRV11E/TRV20E only) (p. 21) rj START/STOP button (p.
210 Identifying the parts and controls ts AUDIO/VIDEO jack (p. 41, 80, 97) td i (headphones) jack When you use headphones, the speaker on your camcorder is silent. tf OPEN/EJECT lever (p. 20) tg Tripod receptacle Make sure that the length of the tripod screw is less than 6.
Quick Reference Кpaткий cпpaвочник 211 Identifying the parts and controls Note on the Carl Zeiss lens Your camcorder is equipped with a Carl Zeiss lens which can reproduce a fine image. The lens for your camcorder was developed jointly by Carl Zeiss, in Germany, and Sony Corporation.
212 Identifying the parts and controls Remote Commander The buttons that have the same name on the Remote Commander as on your camcorder function identically to the buttons on your camcorder. 1 PHOTO button (p. 45, 138) 2 DISPLAY button (p. 37) 3 Memory control buttons PLAY/INDEX/+/– button (p.
Quick Reference Кpaткий cпpaвочник 213 Identifying the parts and controls To prepare the Remote Commander Insert 2 R6 (Size AA) batteries by matching the + and – polarities on the batteries to the + – marks inside the battery compartment.
214 Identifying the parts and controls Operation indicators 1 Cassette memory indicator (p. 29, 171) 2 Remaining battery time indicator (p. 29) 3 Zoom indicator (p. 27) /Exposure indicator (p. 64) /Data file name indicator (DCR-TRV11E/TRV20E only) (p.
Quick Reference Кpaткий cпpaвочник 215 Identifying the parts and controls qg NIGHTSHOT indicator (p. 31) qh Warning indicators (p. 183) qj Tape counter indicator (p. 72) /Time code indicator (p. 29) /Self-diagnosis indicator (p. 182) /Tape photo indicator (p.
216 English Quick Function Guide Functions to adjust exposure (in the recording mode) • In a dark place • In insufficient light • In dark environments such as sunset, fireworks, or general night.
Quick Reference Кpaткий cпpaвочник 217 Aнглийcкий Кpaтк оe p yк ово дcтво по фyнкциям Фyнкции для peгyлиpовки экcпозиции (в peжимe.
218 English Index A, B AC power adaptor ..................... 14 Adjusting viewfinder ................ 25 Audio dubbing ......................... 104 AUDIO MIX ............................. 118 Audio mode .............................. 120 AUTO SHTR .
Quick Reference Кpaткий cпpaвочник 219 Pyccкий Aлфaвитный yкaзaтeль А, Б, В, Г Aдaптep поcлeдовaтeльного поpтa ................................. 157 Ayдиопepeзaпиcь ................ 104 Ayдиоpeжим .
Sony Corporation Printed in Japan.
An important point after buying a device Sony DCR-TRV6E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony DCR-TRV6E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony DCR-TRV6E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony DCR-TRV6E you will learn all the available features of the product, as well as information on its operation. The information that you get Sony DCR-TRV6E will certainly help you make a decision on the purchase.
If you already are a holder of Sony DCR-TRV6E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony DCR-TRV6E.
However, one of the most important roles played by the user manual is to help in solving problems with Sony DCR-TRV6E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony DCR-TRV6E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
