Instruction/ maintenance manual of the product CPD-E220 Sony
Go to page of 34
SERVICE MANUAL SPECIFICATIONS CRT 0.24 mm aperture grille pitch (center) 17 inches measured diagonally 90-degree deflection FD Trinitron Viewable image size Approx.
CPD-E220/E215E/E220E – 2 – LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part hav- ing a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods.
CPD-E220/E215E/E220E – 3 – POWER SAVING FUNCTION DIAGNOSIS This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer , the screen will go blank and the 1 (po wer) indicator will either light up green or flash orange.
CPD-E220/E215E/E220E – 4 – TIMING SPECIFICATION PRIMARY MODE MODE AT PRODUCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 RESOLUTION 640 X 480 800 X 600 832 X 624 1024 X 768 1024 X 768 720 X 400 640 X 480 1280 X 1024 CLOCK 25.175 MHz 56.
CPD-E220/E215E/E220E – 5 – TABLE OF CONTENTS Section Title Page 1. GENERAL .................................................................. 1-1 2. DISASSEMBLY 2-1. Cabinet Removal ................................................. 2-1 2-2. A and D Boards Removal .
CPD-E220/E215E/E220E GND GND Connector (2P) GND CN2 CN602 CN310 CN303 CN304 CN307 CN309 CN301 CN302 CN903 Screw (+BVTT 3 x 8 ) I/O cable assembly 1 Screw (+M 4 x 8) 4 Cable Cable cover 5 6 2 8 3 Three.
CPD-E220/E215E/E220E A board 1 3 2 Tention spring GND GND CN602 CN903 Connector (2P) CN2 CN307 Anode cap (See page 2-3.) Neck assembly Degauss coil Deflection yoke 1 Two degauss coil holder Two degaus.
CPD-E220/E215E/E220E 2-3 2-5. H BOARD REMOVAL 3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling up it in the direction of the arrow C .
CPD-E220/E215E/E220E 2-6. HARNESS LOCATION CN903 CN902 CN501 CN603 CN505 CN901 CN502 CN310 CN301 CN307 CN309 CN302 CN304 CN303 CN504 CN602 CN2 CN1 Picture tube Degauss coil A board AC inlet D board H .
CPD-E220/E215E/E220E VR501 SECTION 3 SAFETY RELATED ADJUSTMENT 3-1 When replacing parts shown in the table below, the following operational checks must be performed as a safety precaution against X-ray emissions from the unit.
CPD-E220/E220E/E215E #2 SECTION 4 ADJUSTMENTS 4-1 • Landing Fine Adjustment 1. Put the set inside the Helmholtz coil. 2. Set TLH plate to zero position. 3. Input the single green signal. 4. Demagnetize the CRT surface with the hand degausser , and perform auto degaussing.
CPD-E220/E220E/E215E 4-2 A 312 mm B MODE All mode 234 mm a 1.5 mm b 1.5 mm a B A b B A A 0.30 mm B MODE All mode 0.35 mm • Convergence Rough Adjustment 1. Enter the crosshatch signal. 2. Recheck focus and readjust when focus was worse. 3. Adjust roughly H.
5-1 5-2 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS CN301 2 4 6 SIGNAL-IN HD15 PIG-TAIL RED GREEN BLUE CN302 TO D BOARD CN901 TO D BOARD CN902 7 B 3 4 8 9 5 CLAMP H_RTN V_RTN SDA/I SCL/I G1 A TO D BOARD CN603 C 5 1 3 4 6 CN303 TO D BOARD FBT HV G2 FV1 CRT R.
5-3 5-4 B-SS3562<NH.>-BD2-EPS05 CN902 1 +5V IC903 RESET IN OUT 19 20 PD0/V SYNCO 34 PA6 PD4/ITB ABL/O H_RETURN 24 17 18 19 16 14 8 HDRV 5 OUT 3 FLYBACK 13 VOUT1 12 IC401 V OUT VOUT2 1 HFLB 11 EW.
5-5 5-6 5-2. FRAME SCHEMATIC DIAGRAM 5-3. CIRCUIT BOARDS LOCATION D H A DGC A D HV H USER CONTROL DEFLECTION,HV,POWER V DY H DY RGB OUT VIDEO, µ-COM,DEFLECTION CONTROL, B-SS3562<NH.>-KESSENZU-EPS05 1 2 3 4 5 6 CN301 6P RGND RED GGND GREEN BGND BLUE 1.
5-7 5-8 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in µF unless otherwise noted. (pF: µµF) Capacitors without voltage indication are all 50 V. • Indication of resistance, which does not have one for rating electrical power, is as follows.
1 A B C D E F G H I 2 12 13 11 10 9 8 7 6 5 4 3 14 0.2 0.8 1.1 -0.2 0.1 2.6 0.1 2.9 0.1 0.1 2.6 4.4 0.6 1 2 3 2.0 2.9 1.5 4.4 1.1 2.1 4.7 0.6 2.1 2.9 2.
1 A B C D E F G H I 2 12 13 11 10 9 8 7 6 5 4 3 14 5-13 5-14 (3) Schematic Diagrams of D ( a a a a a , b b b b b , c c c c c , d d d d d ) Board • Divided circuit diagram One sheet of D board circuit diagram is divided into four sheets, each having the code D- a to D- d .
5-15 5-16 1 A B C D E F G H I 2 12 13 11 10 9 8 7 6 5 4 3 D Schematic diagram - b board l l l l l • Divided circuit diagram One sheet of D board circuit diagram is divided into four sheets, each having the code D- a to D- d . For example, the destination ab1 on the D- a sheet is connected to ab1 on the D- b sheet.
5-17 1 A B C D E F G H I 2 12 13 11 10 9 8 7 6 5 4 3 14 5-18 • Divided circuit diagram One sheet of D board circuit diagram is divided into four sheets, each having the code D- a to D- d . For example, the destination ab1 on the D- a sheet is connected to ab1 on the D- b sheet.
5-19 5-20 1 A B C D E F G H I 2 12 13 11 10 9 8 7 6 5 4 3 14 D Schematic diagram Ò Ò Ò Ò Ò - c board • Divided circuit diagram One sheet of D board circuit diagram is divided into four sheets, each having the code D- a to D- d . For example, the destination ab1 on the D- a sheet is connected to ab1 on the D- b sheet.
5-23 5-5. SEMICONDUCTORS 1 TOP VIE W n 8 pin DIP 1 TOP VIEW n 20 pin DIP 1 TOP VIE W n 36 pin DIP 1 TOP VIEW n 42 pin DIP 1 TOP VIE W n 32 pin DIP E LETTER SIDE C B GA TE CA THODE ANODE E B C E C B E .
CPD-E220/E220E/E215E 1 3 4 5 10 6 7 9 • Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Items with no part number and no description are not stocked because they are seldom required for routine service.
CPD-E220/E220E/E215E 60 69 51 61 61 70 52 54 62 71 72 53 63 55 64 64 68 65 66 57 67 58 59 56 6-2. PICTURE TUBE 7-685-663-71 +BVTP 4X16 8026114012 7-685-881-09 +BVTT 4X8 The components identified by mark ¡ are critical for safety. Replace only with part number specified.
CPD-E220/E220E/E215E 6-3. PACKING MATERIALS The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité.
An important point after buying a device Sony CPD-E220 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony CPD-E220 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony CPD-E220 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony CPD-E220 you will learn all the available features of the product, as well as information on its operation. The information that you get Sony CPD-E220 will certainly help you make a decision on the purchase.
If you already are a holder of Sony CPD-E220, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony CPD-E220.
However, one of the most important roles played by the user manual is to help in solving problems with Sony CPD-E220. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony CPD-E220 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
