Instruction/ maintenance manual of the product 1721302-04 Snapper
Go to page of 22
A TT A CHMENT OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693756 Hitch (for Baron Series, Broadmoo.
1 T able of Contents Adjustments .........................................................7 Skid Shoe Adjustment .....................................7 Spring T ension .................................................7 Lift Height Adjustment .........
OPERA TING SAFETY O Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. O Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads.
3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit.
4 Checks Bef ore Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity.
5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion.
6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year.
7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground.
8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Figure 7. Lift Lever Quadrant - Side View Notch 1 Notch 2 Notch 3 Lift Rod Adjustment ELECTRIC/HYDRAULIC LIFT MODELS: In the fully raised position the blade should be 6” off the ground.
9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Low.
10 Initial Setup & Assembly 2 1 3 5 6 7 8 10 16 17 18 28 30 31 29 28 12 13 14 15 32 9 9 9 11 20 22 23 24 25 26 27 19 21 9 9 4 4 3 34 33 43 43 35 36 37 38 41 37 42 40 37 39 NOTE: The dashed-line rod: Landlord/1700/2700-This rod is part of the tractor.
11 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y NOTE: Some of the following setup procedures may already be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Baron/Broadmoor/LT/1600/2600 Series: See Figure 10. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B).
12 Initial Setup & Assembly Install Rear Push Bar Support NOTE: Manual Lift Models-If your tractor is not already equipped with a Large Lift Lever kit, install it at this time. Follow the instructions supplied with the kit. 1. Assemble the push bar support (A, Figure 12) and hitch (F) using the hardware shown in Figure 12.
13 Initial Setup & Assembly Figure 15. Install Push Bar Assembly A. Push Bar Assembly C. Clevis Pins B. Hitch D. Safety Clips Figure 14. Installing Hitch to Rear Bracket A. Push Bar Support C. Lift Rod/Lever B. Washers CONNECT HITCH TO REAR PUSH BAR 1.
14 Initial Setup & Assembly Install Spring Assist Bracket (Baron/Br oadmoor/1600/2600 Models Onl y) NOTE: Spring-assist bracket assembly (Figure 16) does not need to be installed on units with electric/hydraulic lift. 1. Install the spring-assist bracket (A, Figure 16) to trac- tor frame (bracket is mounted underneath frame).
15 Initial Setup & Assembly Install Lift Rod NOTE: Two lift rods are packaged with the Broadmoor/LT/1600/2600 & Landlord/GT/1700/2700 hitch assembly. Use the correct lift rod for manual or hydraulic lift as shown in Figure 9. 1. Assemble lift rod per Figure 19.
16 Initial Setup & Assembly Figure 23. Control Rod Support A. Support B. 5/16-18 x 1-1/2 Capscrews C. 5/16 Centerlock Nuts D. 5/16 Plain Washers E. Spacers Install Angling Control Rod NOTE: If installing the dozer attachment on a unit equipped with a snowcab, replace the control rod sup- port (A, Figure 23) with the hanging support (Ref.
17 Removing & Attaching the Hitch & Blade REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. Put the lift lever in the middle notch (float position). 2. Remove the hair pin clip and washer (D, Figure 25) securing the angling control rod to the clevis.
18 Removing & Attaching Removing & Attac hing Hitch 1. Remove the safety clip (A, Figure 26) and remove the hitch pin (D). 2. Lift the hitch bar (B) off the tractor brackets (C). 3. Remove the spring clips (A, Figures 28 & 29) secur- ing the rear hitch bracket (C) to the lift pivot rod (B).
19 Reinforcement Bracket Installation INST ALL REINFORCEMENT BRA CKET NOTE: This kit applies to the Landlord / 1700 / 2700 Series hydraulic lift models only. 1. Loosen the four capscrews (A, Figure 32) securing the quadrant (B) to the footrest. 2. Insert the reinforcement bracket (B, Figure 31) between the quadrant (B, Figure 32) and foot rest.
T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved.
An important point after buying a device Snapper 1721302-04 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper 1721302-04 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper 1721302-04 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper 1721302-04 you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper 1721302-04 will certainly help you make a decision on the purchase.
If you already are a holder of Snapper 1721302-04, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper 1721302-04.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper 1721302-04. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper 1721302-04 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
