Instruction/ maintenance manual of the product SR275XGH Smeg
Go to page of 16
Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 22 2. POSITIONING OF HOB ___________________________________ 24 3. ELECTRICAL CONNECTI ON ______________________________ 26 4. GAS CONNECTION ______________________________________ 27 5.
Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB.
Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING.
Instructions for the installer 24 2. POSITIONI NG OF HOB The following oper ation requires buildi ng and/or carp entry work so must be carried out by a competent tradesman. Installation can be carried out on var ious materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C).
Instructions for the installer 25 In case of installation on a holl ow compartment with doors, a separating panel has to be pl aced under the hob. Keep a minimum d istance of 10 mm betwee n the bottom of the unit and th e panel surface. The panel has to be easily removable to allow acces s in the event of technical service.
Instructions for the installer 26 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power l ine conform to the data shown on the plate locat ed under the casing.
Instructions for the installer 27 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally.
Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make the con nection to the tank according to the provisions of stand ard s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “ 5.
Instructions for the installer 29 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar.
Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a double head wrench to remove nozzle C a nd assemble the suitable one, follow ing the instructions indicated in the referenc e charts, with respect to the type of gas to use.
Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in parag raph “ 5.
Instructions for the installer 32 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the inst ructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the co mponents on the burner and slide the knobs on the gas tap pins.
Instructions for the installer 33 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased.
Insructions for the user 34 7. USING THE HOB Make sure that the fl ame-baffle crowns, the caps and the grid have been assembled correctly. Grid C (supplied) should be used for "woks" (Chinese pots). Adapter B (supplied) is to be used for small vessels.
Insructions for the user 7.3 Diameter of containers BURNERS Ø min. e max. (in cm) 1 Auxiliary 7-18 2 Semi-rapid 10-24 12-24 3 Average rapid 14-28 4 Large rapid 22-26 5-6 Triple crown 12-34 7 Double crown 7.
Insructions for the user 36 8. CLEANING AND MAINTENANCE NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. Before any intervention, disconnect the p ower supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obv iously after it has cooled.
An important point after buying a device Smeg SR275XGH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smeg SR275XGH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smeg SR275XGH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smeg SR275XGH you will learn all the available features of the product, as well as information on its operation. The information that you get Smeg SR275XGH will certainly help you make a decision on the purchase.
If you already are a holder of Smeg SR275XGH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smeg SR275XGH.
However, one of the most important roles played by the user manual is to help in solving problems with Smeg SR275XGH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smeg SR275XGH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
