Instruction/ maintenance manual of the product ADP8242 Smeg
Go to page of 19
DISHW ASHER How to get the most from your Fully Integrated Dishwasher ADP 8242.
A Helping Hand on the Home Front Page No. 1,2 & 3 4 & 5 6 7 8 9 10 11 12 13 14 15 16 18 Installation Loading Y our Dishwasher Detergent and Rinse Aid Dispenser W ater Softener Control Panel Th.
Installation 1 Y our brand new dishwasher complies with stringent EEC specifications and is fully compatible with any 600mm deep kitchen units. If you are reasonably handy at DIY , installing your dishwasher should be relatively straight forward as long as you stick to the following guidelines.
Installation cont... Stage 1 2 Supplied with the appliance is a metal anti-condensation strip, this should be fixed to the underside of your worktop along the front edge (via the two outer screws).
Installation cont... Stage 4 3 Position the decor door onto the front of the dishwasher by locating the brackets into the two mouldings mounted either side on the top of the door .
Loading Loading the bottom basket 4 The dishwasher has a capacity of 12 place-settings including serving dishes. Before loading the dishes, remove the largest scraps of food to avoid blocking the filter .
IMPORT ANT NOTE In the interest of general safety do not place long bladed knives in the cutlery basket. These items should be laid flat, so as not to cause potential accidental injury when unloading your dishwasher . Loading cont... Adjusting the T op Basket 5 The top basket can be in two different positions depending on the height of the dishes.
W ARNING After loading, ensure that both spray arms are free to r otate. We cannot accept responsibility for dama ge caused by incorrect loading. Y our Dishwasher 6 1 2 3 4 5 6 7 8 Upper Basket Upper .
Deter gent and Rinse Aid Dispenser Filling with detergent 7 The detergent and rinse aid dispenser are on the inside of the door . The detergent dispenser is on the left and the rinse aid dispenser is on the right. Fill the dispenser with detergent before eac h wash.
W ater Softener Filling with salt 8 The dishwasher is equipped with an automatic softener which uses regenerating salts specially developed for dishwashers to remove hardening substances from the water . Hard water leaves whitish marks on the dry dishes, and dishes gradually lose their shine over time.
Control Panel 9 A B C D ST ART button When this button is pressed, the dishwasher is receiving power . PROGRAMME SELECT OR lights When ON, this light indicates the program selected and any failures present (see section "Dealing with malfunction").
The First W ash Switching on 10 The dishwasher must not be turned on until the dishes have been loaded, the dispenser has been filled with detergent, a check has been made that the spray arms turn freely , and the door has been shut. The water tap must also be turned on and salt placed in the container .
T able of Programs 11 1 2 3 4 5 SOAK DELICA TE NORMAL INTENSIVE BIO (*) EN 50242 Pans and dishes awaiting a further wash Cold prewash W ash immediately after use for dishes with light dirt W ash at 45.
Cleaning and Maintenance 1 2 Cleaning the Appliance Make sure that the appliance is disconnected from the electrical mains. The outside surfaces and the inside of the door of the dishwasher must be cleaned regularly with a soft, damp cloth. Never use abrasive or acid deter gents.
How to Deal with Small Problems 1 3 If the dishwasher is to be out of use for a long period The following precautions must be taken: - perform two consecutive pre-rinses; - disconnect the plug from the mains; - leave the door slightly open so that no unpleasant smells can form; - turn off the water tap.
General and T echnical Details 14 T echnical Details Capacity Intake Power Supply V oltage Fuse Rating Width of Appliance Depth of Appliance Dimension with Door Open 12 place settings 1÷9 bar 230 V 1.
Not W orking Pr operly cont... If the dishes are not clean at the end of the program 1 5 Check whether: - the right washing program has been used; - the detergent dispenser has opened correctly; - the.
Electrical Connections IMPORT ANT: ENSURE THA T THE ELECTRICITY SUPPL Y IS SWITCHED OFF BEFORE CONNECTING. 1 6 Y our appliance must be connected to fixed wiring via the use of a double pole switched fused spur outlet with at least 3mm contact separation.
12 Months Guarantee 18 Procedur e when repor ting a fault Give full name, address including post code, home telephone number and business telephone number if appropriate. 1. Quote sales receipt number , make and model number of faulty appliance. This product's reference is as follows: ADP 8242 2.
An important point after buying a device Smeg ADP8242 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smeg ADP8242 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smeg ADP8242 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smeg ADP8242 you will learn all the available features of the product, as well as information on its operation. The information that you get Smeg ADP8242 will certainly help you make a decision on the purchase.
If you already are a holder of Smeg ADP8242, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smeg ADP8242.
However, one of the most important roles played by the user manual is to help in solving problems with Smeg ADP8242. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smeg ADP8242 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
