Instruction/ maintenance manual of the product D-R K Series SMC Networks
Go to page of 8
OUT 2 OUT 1 Example To judge height of work piece To confirm depth of machined hole OUT 1 OUT 2 Trimmer Auto Switch Series D- 첸 7K / D- R 첸 K 0.5 0.5 mm Minimum width differ ence to detect With one switch, various sized w ork pieces can be detected by the diff erence of more than 0.
Sensor unit Amplifier unit Direct mounting type Rail mounting type Specifications Sensor unit Mounting Applicable amplifier unit Status indication Electrical entry Lead wire Impact resistance Insulation resistance Withstand voltage Ambient temperature Enclosure Weight D-RNK, D-RPK Operating position: red light is ON.
Trimmer Auto Switch D- 첸 7K/D-R 첸 K Descriptions Sensor unit Amplifier unit Applicable actuator and operation range (angle) Sensor unit D-Y7K Air gripper Sensor unit D-F7K Air cylinder Air cylinder Amplifier unit 1 Output (OUT1) indication: green Lights up when OUT1 outputs.
Dimensions Sensor unit D-F7K Amplifier unit D-R 첸 K D- 첸 7K/D-R 첸 K D-Y7K 8.6 12 56 46 5 5 12.5 7.7 2.6 3000 ø3.5 21.1 6 30 OUT1 OUT2 READY TRIMMER SWITCH SMC D-RNK 2 -ø3.5 SMC D-F7K Most sensitive position D-Y7K Most sensitive position SMC M2.
Trimmer Auto Switch Safet y Inst ruct io n s Note 1) ISO 4414: Pneumatic fluid power - - General rules relating to systems Note 2) JIS B 8370: Pneumatic system axiom W a r ning Ca uti o n : Operator error could result in injury or equipment damage. W arni n g : Operator error could result in serious injury or loss of life.
Trimmer Auto Switch Precautions 1 Be sure to read before handling 1. Confirm the specifications. Read the specifications carefully and use this product appropriately. The product may be damaged or malfunction if it is used outside the range of specifications of current load, voltage, temperature or impact.
Operating Environment 1 . Perform the following maintenance periodical in order to prevent possible danger due t unexpected trimmer auto switch malfunction 1) Secure and tighten switch mounting screws. If screws become loose or the mounting position dislocated, retighten them after readjusting the mounti position.
1. Connection and removal of connector • Hold the lever and connector body with two fingers and insert the connector straight into the pin until it is locked with a click sound. • To remove the connector, pull it out straight while pressing the lever with one finger.
An important point after buying a device SMC Networks D-R K Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought SMC Networks D-R K Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data SMC Networks D-R K Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, SMC Networks D-R K Series you will learn all the available features of the product, as well as information on its operation. The information that you get SMC Networks D-R K Series will certainly help you make a decision on the purchase.
If you already are a holder of SMC Networks D-R K Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime SMC Networks D-R K Series.
However, one of the most important roles played by the user manual is to help in solving problems with SMC Networks D-R K Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device SMC Networks D-R K Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
