Instruction/ maintenance manual of the product P5414-E Axis
Go to page of 64
USER MANUAL AXIS P5414–E PTZ Dome Network Camera.
About this Document This manual is intended for administrators and users of the AXIS P5414–E PTZ Dome Network Camera, and is applicable to rmware 5.55 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product.
Europe This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states.
AXIS P5414–E PTZ Dome Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS P5414–E PTZ Dome Network Camera Table of Contents Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Symptoms, Possible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . .
AXIS P5414–E PTZ Dome Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 6 7 8 1 Control button 2 Status LED indicator 3 SD memory card slot 4 Audio connector 5 I/O connector 6 Power connector 7 Network connector (PoE+) 8 Part number (P/N) & Serial number (S/N) Connectors and Buttons For technical specications, see page 59 .
AXIS P5414–E PTZ Dome Network Camera Hardware Overview I/O Connector Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notications.
AXIS P5414–E PTZ Dome Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product.
AXIS P5414–E PTZ Dome Network Camera Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must congure your network router to allow incoming data trafc to the product.
AXIS P5414–E PTZ Dome Network Camera Accessing the Product Click the Active/Inactive buttons to manually activate and inactive the product’s output port. For information about how to enable and congure output buttons, see page 25 . The Manual Trigger button is used to trigger an action rule from the Live View page.
AXIS P5414–E PTZ Dome Network Camera Accessing the Product Click the View Full Screen button and the video image will ll the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view. The Record button is used to record the current video stream.
AXIS P5414–E PTZ Dome Network Camera Accessing the Product Pan and Tilt bars – Use the arrows to pan and tilt the camera view, or click on a position on the bar to steer the camera view to that position. Zoom bar – Use the arrows to zoom in and out, or click on a position on the bar to zoom to that position.
AXIS P5414–E PTZ Dome Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.
AXIS P5414–E PTZ Dome Network Camera Media Streams The AMC Control Panel can be used to congure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on rst use, after which it can be congured.
AXIS P5414–E PTZ Dome Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS P5414–E PTZ Dome Network Camera Setting Up the Product Setting Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page.
AXIS P5414–E PTZ Dome Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can congure the following: • Video stream settings. See page 17 . • Stream proles. See page 18 .
AXIS P5414–E PTZ Dome Network Camera Video and Audio • Rotate image . If required, the image can be rotated. • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount.
AXIS P5414–E PTZ Dome Network Camera Video and Audio Image Appearance Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation. The value 0 gives a black and white image. The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image.
AXIS P5414–E PTZ Dome Network Camera Video and Audio Gain , measured in decibel (dB), is the amount of amplication applied to the image. A high gain may provide a better image in low light situations but will increase the amount of image noise. Set Gain to • Auto to set the gain automatically.
AXIS P5414–E PTZ Dome Network Camera Video and Audio Overlay Image An overlay image is a static image superimposed over the video stream. The image, for example company logo, is used to provide extra information or to mask a part of the image.
AXIS P5414–E PTZ Dome Network Camera Video and Audio Privacy Mask A privacy mask is an area of solid color that prohibits users from viewing parts of the monitored area. Privacy masks cannot be bypassed via the VAPIX® Application Programming Interface (API).
AXIS P5414–E PTZ Dome Network Camera Video and Audio • Yellow — the signal is becoming distorted. • Red — the signal is distorted. Use the Encoding option to select digital audio encoding format. • AAC requires a license for both encoding and decoding.
AXIS P5414–E PTZ Dome Network Camera Live View Cong Live View Cong You can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 18 .
AXIS P5414–E PTZ Dome Network Camera Live View Cong Browser Viewer Description AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alternative to AMC (Motion JPEG). Requires one of the following installed on the client: • JVM (J2SE) 1.
AXIS P5414–E PTZ Dome Network Camera Live View Cong - Pulse activates the output for a dened period of time. The pulse time can be set from 1/100 second to 60 seconds.
AXIS P5414–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) Preset Positions A preset position is a predened view that can be used to quickly steer the camera to a specic location. Preset positions can be accessed in several ways: • By selecting the preset from the Preset positions drop-down list in the Live View Page.
AXIS P5414–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Gatekeeper The Advanced Gatekeeper monitors an area such as an entrance gate. When motion is detected in the monitored area, the Gatekeeper will steer the camera to a selected preset position.
AXIS P5414–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Click Get to set the coordinates. Proceed to where the upper right point of zone should be located and click Get . Give the zone a descriptive name and click OK . To include the name of the OSDI zone in the overlay text, go to Video & Audio < Video Stream < Overlay Settings .
AXIS P5414–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Note • The administrator can enable and disable PTZ controls for selected users. • To identify different users in the viewer group, cookies must be enabled on the client.
AXIS P5414–E PTZ Dome Network Camera Detectors Detectors Motion Detection Motion detection is used to generate an alarm whenever movement starts or stops in the camera view.
AXIS P5414–E PTZ Dome Network Camera Detectors Motion Detection Parameters The parameters controlling motion detection are described in the table below: Parameter Object Size History Sensitivity Description Object size relative to window size. Object memory length.
AXIS P5414–E PTZ Dome Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting.
AXIS P5414–E PTZ Dome Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed.
AXIS P5414–E PTZ Dome Network Camera Events Events The Axis product can be congured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that denes how and when the action is triggered is called an Action Rule .
AXIS P5414–E PTZ Dome Network Camera Events - Recording — triggers the rule when the Axis product records to the storage device. The recording status trigger can be used to notify the operator, for example by ashing LED lights, if the product has started or stopped to record to the storage device.
AXIS P5414–E PTZ Dome Network Camera Events 6. Under Actions , select Record Video from the Type drop-down list. 7. Select a Stream prole and congure the Duration settings as described below. 8. Select Network Share from the Storage drop-down list.
AXIS P5414–E PTZ Dome Network Camera Events 2. Enter a descriptive name. 3. Select a recipient Type . 4. Enter the information needed for the recipient type.
AXIS P5414–E PTZ Dome Network Camera Events 1. Go to Events > Recurrences and click Add . 2. Enter a descriptive name and recurrence pattern. 3. Click OK . To use the recurrence in an Action Rule, rst select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list.
AXIS P5414–E PTZ Dome Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 40 . • To set up action rules, see page 36 . • To access recordings, see Recording List, on page 40 .
AXIS P5414–E PTZ Dome Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and rst upload the new language le.
AXIS P5414–E PTZ Dome Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS P5414–E PTZ Dome Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups.
AXIS P5414–E PTZ Dome Network Camera System Options To install a self-signed certicate: 1. Go to System Options > Security > Certicates . 2. Click Create self-signed certicate and provide the requested information. To create and install a CA-signed certicate: 1.
AXIS P5414–E PTZ Dome Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.
AXIS P5414–E PTZ Dome Network Camera System Options ping -l 408 -t <IP address> Windows example (this may require that you run the command prompt as an administrator) arp -s 192.
AXIS P5414–E PTZ Dome Network Camera System Options Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers. The secondary DNS server is optional and will be used if the primary is unavailable. NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network.
AXIS P5414–E PTZ Dome Network Camera System Options Enable/Disable - When enabled, the Axis product attempts to congure port mapping in a NAT router on your network, using UPnP TM . Note that UPnP TM must be enabled in the product (see System Options > Network > UPnP ).
AXIS P5414–E PTZ Dome Network Camera System Options Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the elds provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information.
AXIS P5414–E PTZ Dome Network Camera System Options Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour .
AXIS P5414–E PTZ Dome Network Camera System Options To add a network share: 1. Go to System Options > Storage . 2. Click Network Share . 3. Enter the IP address, DNS or Bonjour name to the host server in the Host eld. 4. Enter the name of the share in the Share eld.
AXIS P5414–E PTZ Dome Network Camera System Options For information about rmware upgrade, see Upgrading the Firmware, on page 55 . Support Support Overview The System Options > Support > Support Overview page provides information on troubleshooting and contact information, should you require technical assistance.
AXIS P5414–E PTZ Dome Network Camera System Options To open the Script Editor, go to System Options > Advanced > Scripting . If a script causes problems, reset the product to its factory default settings, see page 53 . For more information, see www.
AXIS P5414–E PTZ Dome Network Camera Repainting the Camera Repainting the Camera The covers can be repainted to match the installation environment. The material used in the covers is ASA Geloy XTWM206. Use paint suitable for this material. 1. Remove the two top cover screws.
AXIS P5414–E PTZ Dome Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS P5414–E PTZ Dome Network Camera Troubleshooting arp -s <IP address> <serial number> temp ping -l 408 <IP address> In Windows , type the following from a command/DOS prompt (th.
AXIS P5414–E PTZ Dome Network Camera Troubleshooting The IP address has been changed by DHCP IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been changed, use AXIS IP Utility or AXIS Camera Management to locate the product on the network.
AXIS P5414–E PTZ Dome Network Camera Troubleshooting Lower frame rate than expected See Performance Considerations, on page 63 . Reduce the number of applications running on the client computer. Limit the number of simultaneous viewers. Check with the network administrator that there is enough bandwidth available.
AXIS P5414–E PTZ Dome Network Camera Technical Specications Technical Specications Function/group Item Specications Models AXIS P5414–E 50 Hz AXIS P5414–E 60 Hz Image sensor 1/2.9” progressive scan RGB CMOS Lens f=4.7 mm – 84.6 mm F1.
AXIS P5414–E PTZ Dome Network Camera Technical Specications Function/group Item Specications Security Password protection, IP address ltering, HTTPS encryption*, IEEE 802.
AXIS P5414–E PTZ Dome Network Camera Technical Specications Function/group Item Specications Casing IP66– and NEMA 4X–rated metal casing (aluminum), clear dome (PC), sunshield (ASA) memory 256MB RAM, 128 MB Flash Power Power over Ethernet Plus (PoE+) IEEE 802.
AXIS P5414–E PTZ Dome Network Camera Technical Specications Digital input — Connect to GND to activate, or leave oating (unconnected) to deactivate. 0 to +30 V DC Congurable (Input or Output) 3–6 Digital output — Internal connection to ground when activated, oating (unconnected) when deactivated.
AXIS P5414–E PTZ Dome Network Camera Technical Specications Function Pin Notes Microphone/Line in 1 Microphone or line in (mono) GND 2 Ground Line out 3 Line audio out GND 4 Ground SD Card Slot Supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 10.
User Manual Ver. M1.8 AXIS P5414–E PTZ Dome Network Camera Date: September 2013 © Axis Communications AB, 2013 Part No. 52979.
An important point after buying a device Axis P5414-E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axis P5414-E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axis P5414-E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axis P5414-E you will learn all the available features of the product, as well as information on its operation. The information that you get Axis P5414-E will certainly help you make a decision on the purchase.
If you already are a holder of Axis P5414-E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axis P5414-E.
However, one of the most important roles played by the user manual is to help in solving problems with Axis P5414-E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axis P5414-E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
