Instruction/ maintenance manual of the product 2000i Smart Technologies
Go to page of 15
99-00496-00 Rev A0 Interactive Whiteboard Projector Replacement Guide for Projector Replacement Kits NEC MT1060R (03-00043) and NEC MT860R (03-00041) 2000i.
FCC Warning This equipment has been tested and found to comp ly wi th the limits for a Class A digita l device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial env ir onment.
99-00496-00 Rev A0 Contents Replacing the Project or in a 2000i ................................................... 1 Aligning the Proj ected Image ........................................................... 6 Customer Support ........................
.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 1 Replacing the Projector in a 2000i Use these instructions to install a replacem ent NEC MT860 or NEC MT1060 projector in your Rear Projection SMART Board 2000i interactive whiteboard. To remove the original projector 1.
2 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 5. With another person supporting the projector, reach through the view port and remove the three nuts (including the steel and nylon washers) that secure the projector in place and then remove the projector.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 3 6. Set the projector down on a flat surface and remove the projector plate from the projector: Using the provided hex key, loosen and remove the four sets of screws, spacers and washers at the corners of the plate.
4 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 8. Slide the projector plate back into plac e by maneuvering the screws through the cabinet slots. With a partner supporting the bottom of the projector, use the provided 7/16" nut driver to secure the projector plate in pl ace using the nuts and washers that you removed in step 5.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 5 9. Connect the video, power and serial cables to the projector, along with any other cables (VCR, external monitor, etc. ) that you removed in step 2. 10. Replace the strap that secures t he projector to the projector plate.
6 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 Aligning the Projected Image If the projected image is blurry or does not fit the screen, complete the four adjustment procedures that follow.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 7 To adjust the image laterally 1. Crouch behind the projector and look at the projected image through the view port. 2. Using the supplied 7/16" nut driver, loosen the two nuts on the left side of the projector plate.
8 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To change the image size 1. Crouch behind the projector and look at the projected image through the view port. 2. Loosen the four hex screws that secure the proj ector to the projector plate using the provided 3 mm hex key.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 9 Screen R emoved for Clarity As you maneuver the hex key through the acce ss holes, watch it from the side to see when it engages with the hex screw. Look here t o see when the he x key engage s with t he scr ew 4.
10 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To move the image up or down 1. Crouch down in front of the screen. 2. Look underneath the pen tray and locate the El ectronics Tray. Locate a plastic cap on the right side of the Electronics Tray.
99-00496-00 REV A0 Projector Replacement Guide for the 2000i 11 Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact your local reseller first if you experience problems with any SMART product.
An important point after buying a device Smart Technologies 2000i (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smart Technologies 2000i yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smart Technologies 2000i - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smart Technologies 2000i you will learn all the available features of the product, as well as information on its operation. The information that you get Smart Technologies 2000i will certainly help you make a decision on the purchase.
If you already are a holder of Smart Technologies 2000i, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smart Technologies 2000i.
However, one of the most important roles played by the user manual is to help in solving problems with Smart Technologies 2000i. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smart Technologies 2000i along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center