Instruction/ maintenance manual of the product 3100 Skil
Go to page of 11
For English V ersion V ersion française V ersión en español See page 2 V oir page 12 V er la página 12 Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcion.
2. General Safety Rules “ READ ALL INSTRUCTIONS” Failure to follow the safety rules listed below and other basic safety precautions may result in serious personal injury. THINK SAFETY Safety is a combination of operator common sense and alertness at all times when the X-Bench is being used.
3. Read and understand all instructions for use of X- Bench and insert plates with tools. Failure to follow all instructions listed below may result in serious personal injury. Use only with Skil accessory insert plates (jig saw, drill press, belt sander and router).
Replace damaged cords immediately. Use of damaged cords can shock, burn or electrocute. Always use proper extension cord. If an extension cord is necessary, a cord with adequate size conductors should be used to prevent excessive voltage drop, loss of power or over- heating.
5. 1. Opening the X-Bench a . T he X-Bench comes in the folded position and no assembly is r equired. In order to open the X-Bench, the user must pull and twist the main knob, located by the handle, to the open position (Fig.
c. Once the user sets one leg at the desired height, follow the same steps for the remaining three legs. 4. Adjustable Foot – for Leveling Bench a. If you are working in an area that is not level, we have provided a solution. We have an adjustable foot that will extend 1.
7 . M ake sure X-Bench is not plugged in and m ain outlet is off. 8. Power Switch a. The female plug is located on the bottom of the switch and the m ale plug is located on the side of the switch box (Fig. 11). C onnect the switch box to an electrical outlet by using an e xtension cord.
11. Tail Vise (Sold Separately) a. Locate the following parts: (1) Clamp block (MDF), (2) Guide rods, (1) Threaded rod, (6) Bolts and (6) Bolt covers. b. Position clamp block (MDF) over guide rods, and threaded r od as shown in figure 16 c . Securely attach guide block to the rods with (6) washer and bolts provided (Fig.
15. Shelf and Tool Bag (Sold Separately) a. Shelf and tool bag come fully assembled. b. There are four hooks under the work bench (Fig. 23.) c. Attach the Velcro straps located on the shelf to the hooks under the table (Fig. 23). Note: Unit can fold up with shelf and bag attached.
10 . 15. Universal Insert Plate: a. A blank insert plate is provided with the X-Bench. This area is meant to be used only with the Skil insert plate technology which is sold separately. The insert plates which can be purchased separately are a jigsaw insert plate, sander insert plate, router insert plate and a drill press insert plate.
11 . Direction of Cut Direction of Cut.
An important point after buying a device Skil 3100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Skil 3100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Skil 3100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Skil 3100 you will learn all the available features of the product, as well as information on its operation. The information that you get Skil 3100 will certainly help you make a decision on the purchase.
If you already are a holder of Skil 3100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Skil 3100.
However, one of the most important roles played by the user manual is to help in solving problems with Skil 3100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Skil 3100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
