Instruction/ maintenance manual of the product Q6042 Axis Communications
Go to page of 32
AXIS Q604 Series AXIS Q6042 PTZ Dome Network Camera AXIS Q6044 PTZ Dome Network Camera AXIS Q6045 PTZ Dome Network Camera E N G L I SH Installation Guide.
Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country . Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license.
Australia/New Zealand This digital equipment fullls the requirements for RF emission according to the Class A limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded. Notice! This is a Class A product.
.
AXIS Q604 Series Safety Infor mation Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury .
AXIS Q604 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing.
AXIS Q604 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
8.
AXIS Q604 Series Installation Guide This Installation Guide provides instructions for installing AXIS Q6042/Q6044/Q6045 Mk II PTZ Dome Network Camera on your network. For other aspects of using the product, see the User Manual available at www .axis.com Installation Steps 1.
AXIS Q604 Series Hardware Overview 1 2 4 5 6 7 8 9 10 3 1 Unit holder (3x) 2 Camera base lid 3 Camera base lid screw T20 (3x) 4 Hook for safety wire 5 P art number (P/N) & Serial number (S/N) 6 Ca.
AXIS Q604 Series Camera Unit 1 2 3 4 1 SD card slot (SDHC) 2 Status LED indicator 3 Control button 4 P ower button Dome Cover 1 2 3 4 5 1 Dome bracket screw T20 (4x) 2 Dome bracket 3 Dome cover 4 Dome.
AXIS Q604 Series Hard Ceiling Mount 1 2 1 Mounting plate 2 Safety wire Drop Ceiling Mount 1 2 3 4 5 6 7 1 Mounting plate 2 Mounting plate screw T20 (3x) 3 Bracket arm 4 Bracket arm screw T20 (3x) and .
AXIS Q604 Series LED Indicators LED Color Indication Unlit Connection and normal operation Amber Steady during startup. Flashes during rmware upgrade. Amber/red Flashes amber/red if network connection is unavailable or lost. Red Flashes red for rmware upgrade failure.
AXIS Q604 Series NO NO NO TICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specic use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions.
AXIS Q604 Series Multi-Connector Cable (sold separately) When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller .
AXIS Q604 Series Digital input – Connect to pin 1 to activate, or leave oating (unconnected) to deactivate. 0 to max 40 V DC Congurable (Input or Output) 3–6 Digital output – Connected to pin 1 when activated, oating (unconnected) when deactivated.
AXIS Q604 Series I/O connector 1 2 3 4 5 6 DC power input AC power input Specications Operating Conditions The Axis product is intended for indoor use.
AXIS Q604 Series Connectors SD Card Slot Supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 1 0. Install the Hardware NO NO NO TICE TICE TICE • The AXIS product shall be connected using a shielded network cable (STP).
AXIS Q604 Series 2. Remove the dome bracket screws and remove the dome bracket and the dome cover from the dome ring. 3. Attach the dome bracket and the dome cover to the dome ring and tighten the screws (torque 1.2 Nm). 4. To install an SD card (not included), see Install an SD Card on page 19 .
AXIS Q604 Series 5. Route and connect the network cable and the multi-connector cable (sold separately), if applicable, to the camera. NO NO NO TICE TICE TICE • Be careful not to damage the cables when connecting them.
AXIS Q604 Series 1 2 1 Ceiling tile 2 Hole diameter 225 mm (8.9 in.) 3. Assemble the ceiling bracket and attach it to the ceiling tile. Make sure the arrows on the mounting plate and the ceiling bracket are pointing in the same direction for the logotypes on the camera and the trim ring to align.
AXIS Q604 Series 2 1 3 4 5 1 Mounting plate 2 Ceiling bracket 3 Ceiling tile 4 Safety wire 5 Hook for safety wire 1 0. Slide the unit holders on the network camera into the slots in the mounting plate and rotate the camera unit. 1 1. Install the supplied midspan.
AXIS Q604 Series 1 2 1 Trim ring 2 Trim ring screw T20 (4x) Bracket Mount (sold separately) 1. Install the selected bracket according to the instructions supplied with the bracket. If drilling is required, make sure to use drill bits, screws and plugs that are appropriate for the material.
AXIS Q604 Series 1 2 3 4 1 Screw T30 (3x) 2 Slot for unit holder (3x) 3 Safety wire 4 Wall bracket (mounting example) 5. Connect the network cable and the multi-connector cable (sold separately), if applicable, to the camera. NO NO NO TICE TICE TICE • Be careful not to damage the cables when connecting them.
AXIS Q604 Series 6. Turn the cable holders to keep the cables in place. 7. Put the camera base lid back in its original position and tighten the screws (torque 1.5 Nm). 8. Slide the unit holders on the network camera into the slots in the mounting bracket and rotate the camera unit.
AXIS Q604 Series Access the Product Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream.
AXIS Q604 Series Warranty Information For information about Axis’ product warranty and thereto related information, see www .axis.com/warranty/ 27 E N G L I SH.
.
Regulatory I nformation USA This equipment has been tested using an unshielded network cable (UTP) and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
.
.
Installation Guide V er . M2.8 AXIS Q604 Series Date: August 20 14 © Axis Communications AB, 2014 P art No. 59 146.
An important point after buying a device Axis Communications Q6042 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axis Communications Q6042 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axis Communications Q6042 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axis Communications Q6042 you will learn all the available features of the product, as well as information on its operation. The information that you get Axis Communications Q6042 will certainly help you make a decision on the purchase.
If you already are a holder of Axis Communications Q6042, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axis Communications Q6042.
However, one of the most important roles played by the user manual is to help in solving problems with Axis Communications Q6042. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axis Communications Q6042 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
