Instruction/ maintenance manual of the product P7216 Axis Communications
Go to page of 16
INSTALLATION GUIDE AXIS P7216 Video Encoder E N G L I SH.
Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license.
Europe This digital equipment fullls the requirements for RF emission according to the Class B limit of EN 55022. This product fullls the requirements for immunity according to EN 61000-6-1 residential, commercial and light-industrial environments.
.
AXIS P7216 Video Encoder Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
AXIS P7216 Video Encoder Safety Instructions NOTICE NOTICE NOTICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing.
AXIS P7216 Video Encoder Installation Guide This Installation Guide provides instructions for installing AXIS P7216 Video Encoder on your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps 1.
AXIS P7216 Video Encoder 2 Network connector SFP 3 Network connector RJ45 4 Auxiliary connector RJ45 (maintenance) 5 Card slot (microSD) x4 6 I/O terminal connector x4 7 RS-485/422 connector x4 8 Cont.
AXIS P7216 Video Encoder Connectors For specications, see page 10 . BNC connector - Each video input is terminated using a coax/BNC connector. Connect a 75 Ohm coaxial video cable; the recommended maximum length is 800 feet (250 meters).
AXIS P7216 Video Encoder Power connector - 2-pin terminal block for power input. Use a limited power source (LPS) with either a rated output power limited to £ 100 W or a rated output current limited to £ 5 A. I/O terminal connector - Use in applications for e.
AXIS P7216 Video Encoder Connectors I/O terminal connector 6-pin terminal block for: • Digital Input • Digital Output • Auxiliary power and ground (GND) 1 2 3 4 5 6 Function Pin Notes Specications GND 1 Ground 3.3 V DC Power 2 Can be used to power auxiliary equipment.
AXIS P7216 Video Encoder must be connected in parallel with the load, for protection against voltage transients. 3. 3 V max 250 mA 1 2 A B A I/O congured as input B I/O congured as output Power connector DC power input 2-pin terminal block for power input.
AXIS P7216 Video Encoder Audio Input Audio Output 1 Tip Microphone/Line in 2 Ring Line out (mono) 3 Sleeve Ground Ground RS-485/422 connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
AXIS P7216 Video Encoder Connect the cables 1. Connect the video encoder to the network using a network cable RJ45 and/or a SFP cable. 2. Optionally connect the external input/output devices. 3. Optionally connect active speakers and/or external microphones.
AXIS P7216 Video Encoder Further Information The User Manual is available at www.axis.com Visit www.axis.com/techsup to check if there is updated rmware available for your network product. To see the currently installed rmware version, go to Setup > About .
Installation Guide Ver. M1.8 AXIS P7216 Video Encoder Date: May 2013 © Axis Communications AB, 2013 Part No. 50452.
An important point after buying a device Axis Communications P7216 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axis Communications P7216 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axis Communications P7216 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axis Communications P7216 you will learn all the available features of the product, as well as information on its operation. The information that you get Axis Communications P7216 will certainly help you make a decision on the purchase.
If you already are a holder of Axis Communications P7216, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axis Communications P7216.
However, one of the most important roles played by the user manual is to help in solving problems with Axis Communications P7216. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axis Communications P7216 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
