Instruction/ maintenance manual of the product SD2100 Shiro
Go to page of 14
• User Manual • SD2100 Digital Enhanced Cordless Communication.
1 Contents What the symb ols me an ................................................................... 1 The Handset and Bas e Unit ............................................................... 2 Setting up your telephone ...........................
2 Press to begin, answ er and end a telephone call. Call button Clear / On-Off /END button The Handset and Base Unit Press to enter menu mode and enter sub- menu.
3 Setting up your telephone Connection and con ditions for use You can connect your SD 2100 to a direct exchange line (DEL), a line connected to a local exchange, with its own phone number; to an exte nsion socket connected to a DEL; or to an extension on an approved compat ible PBX.
4 Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack the base unit and plug the telephone line cord into the telephone port.
5 the base unit from the telephone line and the mains socket when there are storms in your area. Damage caused by lightning is not covered by the Guarantee.
6 • While the mouthpiece is muted, you cannot press any number key to send digits down the line; Press Mute key again to get back to the call. Conference Calling You need to register with your fixed line networ k operator for conference calling service.
7 Call Logs You must subscribe to Caller ID service from your service provider to use this feat ure. Call Logs store information relate d to received calls, missed ca lls and dialed calls. The SD2100 can store up to a maximu m of 30 calls, cons isting of 10 re ceived, missed and d ialed calls respectively.
8 3. Press the OK button The display shows the current volume level 4. Press UP/DOWN button to change the volume 5. Press the OK button to confirm the volume level you want Ringer Melody (EXT / INT) You can choose the ringer Melody following the below instruction .
9 6. Press OK button to confirm To delete call barring number 1. Press MENU button then UP/DOWN button until the display shows BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number 4. Press the OK button, then UP/DOWN button to the location BARRING 5.
10 4. Press the OK button and press UP/DOWN button to change Dial mode as TONE or PULSE dialing To reset base 1. Press MENU button, then UP/DOWN button to the location BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number and press the OK button, then UP/DOWN button to the location B RESET 4.
11 1. Disconnect the power lead fr om the back of the base unit 2. Press and hold the HANDSET LOCATOR button in the base unit, at the same time connect the power lead into the back of base unit. Release the LOCATOR button after you hear “beep” sound for five times.
12 Troubleshooting Always check first that: • You have followed the steps listed on pa ges to install and set up your SD2100. • All connects are firmly inserted in their sockets. • Mains power is switched on at the socke t. • The handset’s batteries are correctly and se curely installed, and are not run down.
13 The strange noise is caused by interference. Di sconnect the main s power lead from the b ack of the base unit, and then wait for 30 seconds before reconnecting it. There is 'beep' sound while I am on a call. You may be going out of range of the base unit.
An important point after buying a device Shiro SD2100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Shiro SD2100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Shiro SD2100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Shiro SD2100 you will learn all the available features of the product, as well as information on its operation. The information that you get Shiro SD2100 will certainly help you make a decision on the purchase.
If you already are a holder of Shiro SD2100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Shiro SD2100.
However, one of the most important roles played by the user manual is to help in solving problems with Shiro SD2100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Shiro SD2100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
