Instruction/ maintenance manual of the product AF-R120DX Sharp
Go to page of 20
ROOM AIR CONDITIONER INSTALLATION AND OPERATION MANUAL PAGE CONTENTS This INSTALLATION AND OPERATION MANUAL explains the proper use of your new Sharp Air Conditioner. Read these instructions carefully before installing or operating your air conditioner.
2 To aid in answering questions if you call for service or for reporting loss or theft, please record below the model and serial number located on the right side of the unit.
3 SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective wo.
4 INST ALLA TION INSTRUCTIONS Before beginning installation, read these instructions carefully. Use the enclosed MOUNTING KIT for proper installation. The mounting kit is designed for wooden sill double or single hung sash-type windows.
5 No. Accessories Q'ty Right closure assembly Left closure assembly Window sash foam seal 1 1 1 1. Screw driver (medium size Phillips) 2. Tape measure or ruler 3.
6 INST ALLA TION INSTRUCTIONS Open the window sash and place the cabinet on the sill. Close the window sash securely behind the top angle. If there is space between the bottom channel and the sill, fill the gap with a thin board or other hard filler.
7 INST ALLA TION INSTRUCTIONS Closure assembly (Left) 6 Jamb (Left) Top angle Sill 1/2 inch (13mm) Closure assembly (Left) Stool Insert the closure assemblies on both sides into the rails of the jamb. Secure the cabinet to the window stool with 3 screws (L=1", 25.
8 IMPORTANT: Points to keep in mind when using your air conditioner. • Install the air conditioner by following the installation instructions given in the previous section of this manua l. • Make sure the unit is the correct capacity for the area you want to cool.
9 PRECAUTIONS • Allow 3 minutes for the compressor to restart cooling. If you turn the air conditioner off and immediately restart it, allow three minutes for the compressor to restart cooling. There is an electronic device in the unit that keeps the compressor off three minutes for protection.
10 TIMER ON/OFF pad TIMER indicator ENERGY SAVER pad ENERGY SAVER indicator POWER ON/OFF pad POWER indicator Receiver window for remote control signal Display SELECTOR indicator SELECTOR pad TEMPERATURE setting pad ---- Lower temp.
11 HOW TO OPERA TE --- Lower temp. --- Raise temp. Touch POWER ON/OFF pad. • The unit is preset at 74 ° F and HIGH COOL. This will show in the display when the power is first turned on. • POWER indicator and SELECTOR in- dicator (COOL) will light.
12 HOW TO OPERA TE T O CHANGE F AN SPEED AND OPERA TION MODE During operation Touch SELECTOR pad and select the operation mode and fan speed. • SELECTOR indicator and display will light in order as you touch.
13 EXHAUST Lever HOW TO OPERA TE Adjust the louvers to change the direction of air flow for uniform and efficient cooling of the room. Vertical louvers Adjusts LEFT/RIGHT air flow If air in your room is stale, set the EXHAUST lever to the OPEN position.
14 HOW TO OPERA TE ON TIMER OPERA TION (If you wish to start the operation 6 hours and 30 minutes later, set the delay time as shown above.) 1 Touch the TIMER ON/OFF pad to set the delayed start time. • The time setting will change as you touch the pad.
15 HOW TO OPERA TE OFF TIMER OPERA TION • This unit has a built-in timer that can be programmed to shut the unit off up to 12 hours in advance. You can set the timer to stop in increments of 30 minutes (0.5 hours) up to 9.5 hours in advance of the stop time, or in 1 hour increments from 10 to 12 hours in advance of the stop time.
16 Insert the batteries in the compartment, making sure the and polarities are properly aligned. HOW TO OPERA TE INST ALLING BA TTERIES Use two size-AAA (R03) batteries. Battery compart- ment cover NOTES: • The battery life is approximately one year with normal use.
17 HOW TO OPERA TE • The time setting will change as you push the button. The display will change as follows; • The last OFF time setting is memorized by the unit and will appear on the display when the button is pushed. • The timer will be set, 5 seconds after the SET TIMER/OFF button is pushed for the last time.
18 ENERGY EFFICIENCY TIPS CLEANING AND MAINTENANCE CLEANING THE FIL TER If the filter is clogged with dust, the amount of air flow will be reduced, resulting in poor cooling performance.
19 BEFORE CALLING FOR SER VlCE IF YOUR AIR CONDITIONER DOES NOT OPERATE PROPERLY, PLEASE CHECK THE FOLLOWING ITEMS BEFORE CALLING FOR SERVICE. AIR CONDITIONER DOES NOT OPERATE AT ALL • Is the unit p.
20 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 SHARP CORPORATION Osaka, Japan Printed in Thailand.
An important point after buying a device Sharp AF-R120DX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sharp AF-R120DX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sharp AF-R120DX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sharp AF-R120DX you will learn all the available features of the product, as well as information on its operation. The information that you get Sharp AF-R120DX will certainly help you make a decision on the purchase.
If you already are a holder of Sharp AF-R120DX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sharp AF-R120DX.
However, one of the most important roles played by the user manual is to help in solving problems with Sharp AF-R120DX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sharp AF-R120DX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
