Instruction/ maintenance manual of the product SFN1 Senco
Go to page of 16
F ASTENING SYSTEMS O P E RA TING INS T R U CTI ONS I N ST R U C C I O N E S D E O P ER AC IO N BE T R I E B S AN LEI TU N G MODE D ’ E M PL O I ● Warnings for the safe use of this tool are included in this manual. ● Los avisos para el uso seguro de esta herramienta están incluidos en este manual.
INHAL TSVERZEICHNIS T ABLE DES MA TIÈRES T ABLE OF CONTENTS T ABLA DE MA TERIAS EMPLOYER’S RESPONSIBILITIES Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to the use of this tool.
2 Safety W arnings ● A visos de Seguridad ● Sicherheitshinweise ● Consignes de Sécurité ● Never use oxygen, carbon dioxide or any other bottled gas as a power source for this tool; the tool will explode and cause serious injury. ● Always wear other personal protective equipment such as hearing protection and hard hat.
● Cloutez uniquement dans la surface de travail ; jamais dans des matériaux trop durs à pénétrer. ● Do not drive fasteners on top of other fasteners or with the tool at too steep of an angle; the fasteners can ricochet and hurt someone.
4 ● Nach einer Reparatur könnte die Möglichkeit bestehen, daß das Gerät beim Anschluß an die Luftzufuhr einen Befestiger austreibt. Deshalb das Gerät immer erst an die Druckluft anschließen und dann laden. ● Make sure all screws and caps are securely tightened at all times.
5 Safety W arnings ● A visos de Seguridad ● Sicherheitshinweise ● Consignes de Sécurité ● Die für diese Geräte verwendeten Druckluft–Kompressoren müssen den gesetzlichen Sicherheitsanforderungen entsprechen. ● Air hose must have a minimum working pressure rating of 150 psig (10.
6 ● Do not load fasteners with trigger or safety element depressed. ● Laden Sie das Gerät nicht, wenn der Auslöser oder die Auslösesicherung betätigt sind. ● No cargue los sujetadores con el disparo o la seguridad oprimidos. ● Do not use tool without DANGER label on tool.
7 T ool Use ● Uso de la Herramienta ● Bedienungsanleitung ● Utilisation de l’Outil ● Read section titled “Safety Warnings” before using tool. ● Vor dem Einsatz des Gerätes bitte die Sicherheitshinweise lesen. ● Lea la sección titulada “Avisos de Seguridad” antes de usar la herramienta.
● Para ajustar la profundidad de clavo, dede primero desconectar el aire. Usando el dedo pulgar o el dedo indice, rote la manivela (localizada a un lado de la placa de nariz) para ajustar el seguro a la profundidad deseada. No sobrepase el seguro mas de 1/4" de pulga de la ultima marca.
9 T ool Use ● Uso de la Herramienta ● Bedienungsanleitung ● Utilisation de l’Outil ● Au cas ou il se produirait un coinçage de clous, coupez l’alimentation en air. ● Wenn ein Nagel klemmt, das Gerät von der Druckluftleitung trennen. ● Pull feeder shoe back into “locked” position and remove nails.
10 Maintenance ● Mantenimiento ● W ar tung ● Entretien ● All screws should be kept tight. Loose screws result in unsafe operation and parts breakage. ● Alle Schrauben und Mutter müssen fest angezogen sein. Lose Schrauben und Muttern bedeuten Sicherheitsrisiko und Teilebruch.
11 T roubleshooting ● Identificación de F allas ● Fehlersuche ● Dépanna ge Tighten screws or install Parts Kit A. Apriete los tornillos o instale el Juego de Partes A (Parts Kit A). Schrauben gut anziehen, ggf. Gerät mit den Teilen aus dem mit “A” gekennzeichneten Reparatursatz instandsetzen.
12 T roubleshooting ● Identificación de F allas ● Fehlersuche ● Dépanna ge Verify adequate air supply or install Parts Kit C. Verifique si el suministro de aire está adecuado o instale el Juego de Partes C (Parts Kit C). Luftzufuhr überprüfeng, ggf.
Options ● Opciones ● A uswahlmöglichkeit ● Options COUNTERSINK DEPTH PART NUMBER PROFUNDIDAD DE LA AVELLANADURA NUMERO DE PARTE VERSENKTIEFE TEILENUMMER PROFONDEUR DE FRAISURE NUMÉRO DE PIÈCE 0" 0 mm EC0119 1/32" ,79 mm EC0120 1/16" 1,59 mm EC0121 1/8" 3,18 mm EC0122 DRIVER Note: 1/8" comes standard with tool.
4,8-8,3 bar 61,2 liter 1/4 in. NPT 5 2 kg 104 1,83 mm 244 mm 305 mm 76 mm 14 Minimum to maximum operating pressure Air Consumption (60 cycles per minute) Air Inlet Maximum Speed (cycles per second) Weight Nails per Magazine Capacity Nail Shank Tool size: Height Tool size: Length Tool size: Width: Main Body 70-120 psi 2.
15 SENCO T OOL & P AR TS W ARRANTY This tool has been designed and constructed using the highest standards of material and workmanship. TOOL AND PARTS WARRANTY: The length of this guarantee is one year from date of purchase by the original retail purchaser .
An important point after buying a device Senco SFN1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Senco SFN1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Senco SFN1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Senco SFN1 you will learn all the available features of the product, as well as information on its operation. The information that you get Senco SFN1 will certainly help you make a decision on the purchase.
If you already are a holder of Senco SFN1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Senco SFN1.
However, one of the most important roles played by the user manual is to help in solving problems with Senco SFN1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Senco SFN1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
