Instruction/ maintenance manual of the product PH6231 Sears
Go to page of 11
® 0W E AL 'S MODEL # SERIAL # PD/PH 4801 PD/PH 6801 PD/PH 623,1 PD/PH 4231 READ AND SAVE THESE [LEA Y CONSERVE ESTAS INSTALLATION INSTALACION MAINTENANCE MANTENIMtENTO |NSTRUCT[ONS |NSTRUCC|ONES.
iNSTALLATiON • iN Typlo_l S_dO D|schsrge [nsta!lat[on demands con_ection of blower opening to existing air ducting system or to a dropper duct with a ceiiing diffuser.
iNSTALLATION ° [NSTALAC[ON Water Connection i. Install float in hoie in the side of bottom pan opposite the pump. Seeparts illustration tO route the water line. Connect per above sketch. 2. Turn on the waterto the cooler and set float valve to maintain 21/_, inch water depth.
ELECTRICAL CONNECTIONS FIELD WiRiNG iNSTRUCTiONS 1. MAiN POWER SUPPLY THiS COOLER iS PREWIRED FOR 115 VOLT OR 230 VOLT, 6OHZ POWER ONLY. MAKE SURE YOU CONNECT YOUR COOLER TO THE CORRECT VOLTAGE.
Jl. THERMOSTAT CABLE |NSTALLATION |L INSTA_C[_N DEL CABLE DEL TERMOSTATO The thermostat for this cooler is connected to the cooler by means of a 6 conductor thermostat cable (not provided). Type CL2, 18 or 20 gauge, UL listed thermostat wire is recommended.
MAiN NANCE ° MANTEN[M[EN The cooler should be serviced at least once a year and more often if required. This includes cleaning,oiling, belt adjustment (if required) and pad repJacemenL Cleaning: I. Remove access doors and inlet air louvers. 2. Remove the overflow standpipe from the drain bushing and allow the reservoir to empty, 3.
OPERATING iNSTRUCTiONS FOR THE PROi=STAT THERMOSTAT CONTROL SPECIAL FEATURES ®All information is saved during power failure or system shut-down and system returns to last operating mode when power is.
SPECIAL FUNCTIONS KWIKSET Presets Press the KWIKSET button to display the DAY or NITE preset or to return to the standard display mode. Pressing the KWIKSET button to either the DAY or NITE preset causes the set point, FAN and COOL settings to assume the values stored in memory.
P CLEAN c NG O NC FULL AUTOMATIC: Fresh water for your evaporative coo]er every 5 hours of operation! How i! works.., The Pro Cleaning System (PCS) will automatically cycle every 5 hours of co®[er pump operation to empty the water reservoir within 1 _/!_ mhwtes.
Troubleshooting Shourd a_ obvious probIem occur with your cooler consult the foiiowing table, ff you cannot correct the problem, contac_ a q_Ja[if_edsewice representative, PROBLEM Water Overflow Blowe.
Aerocool Pro Series Evaporative Coolers - Replacement Parts List Aerocool Pro Series Enfriador Evaporativo - Lista Reemplazo de Partes Replacement Part Parte de Reemptazo PD4801A PD4231A PH4801A PH4231A PD6801A PD6231A PH6801A PH6231A 1 Wet Section (Cabinet) 2 Water Distributor Assy.
An important point after buying a device Sears PH6231 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears PH6231 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears PH6231 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears PH6231 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears PH6231 will certainly help you make a decision on the purchase.
If you already are a holder of Sears PH6231, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears PH6231.
However, one of the most important roles played by the user manual is to help in solving problems with Sears PH6231. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears PH6231 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
