Instruction/ maintenance manual of the product 47006 Sears
Go to page of 14
OWNER’S MANUAL Model No. 47006 Sears Canada Inc., 222 Jarvis St., Toronto, Ontario, Canada M5B 2B8 40/2 AMP MANU AL BA TTER Y CHARGER 200 AMP ENGINE ST ARTER CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product.
1 Sears 006 - Sch 552 11/2/95 T able Of Contents W arranty .................................................................. 1 Important Safety Instructions ................................. 2 P arts ..................................................
2 Sears 006 - Sch 552 11/2/95 – SAVE THESE INSTRUCTIONS – w •Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. •Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- tors, airplanes, vans, RV’s, trolling motors, etc.
3 Sears 006 - Sch 552 11/2/95 Description Handle Negative (BLK) cable w/clamps Positive (RED) cable w/clamps Power Cord Circuit Breaker Asm Rectifier Assembly Transformer Owner's Manual (not shown) Wheel Hub Cap Axle Axle mtg. bracket Mounting Foot Rocker Switch 3 pos.
4 Sears 006 - Sch 552 11/2/95 B e fo r e Using Y our B a t ter y C har g er It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
5 Sears 006 - Sch 552 11/2/95 3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
6 Sears 006 - Sch 552 11/2/95 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician.
7 Sears 006 - Sch 552 11/2/95 To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls. And how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
8 Sears 006 - Sch 552 11/2/95 Charging Y our Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
9 Sears 006 - Sch 552 11/2/95 Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all power turned off to the vehicle. 2. Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -).
10 Sears 006 - Sch 552 11/2/95 Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries — motorcycles, garden tractors, etc.
11 Sears 006 - Sch 552 11/2/95 Using the engine start feature Your battery charger can be used to jump-start your car if the battery is low. Follow these instructions on how to use the engine start feature. 1. Set the right-hand OUTPUT SELECTOR switch to the OFF position.
12 Sears 006 - Sch 552 11/2/95 Circuit breaker in charger cycles on and off with a clicking sound. Short start cycle when cranking engine. Ammeter reads less than selected charge rate when charging a discharged battery. Charger makes a loud buzz or hum.
When requesting service or ordering parts, always provide the following information: • Product T ype • Model Number • Part Number • Part Description OWNER’S MANUAL Model No. 47006 40/2 AMP MANU AL BA TTER Y CHARGER 200 AMP ENGINE ST ARTER F or information about troubleshooting Call toll-free from anywhere in the U.
An important point after buying a device Sears 47006 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 47006 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 47006 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 47006 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 47006 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 47006, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 47006.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 47006. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 47006 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
