Instruction/ maintenance manual of the product 200.71450 Sears
Go to page of 16
OWNER’S MANUAL Model No. 200.71450 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 50/15/2 AMP MANU AL BA TTER Y CHARGER 225/125 AMP ENGINE ST ARTER with BA TTERY TESTER CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product.
1 Sch 517 T able Of Contents Warranty .................................................................... 1 Important Safety Instructions .................................. 2 Parts .....................................................................
2 Sch 517 – SAVE THESE INSTRUCTIONS – w •Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. •Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- tors, airplanes, vans, RV’s, trolling motors, etc.
3 Sch 517 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like.
4 Sch 517 B e fo r e Using Y our B a t ter y C h ar g e r It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
5 Sch 517 3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
6 Sch 517 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.
7 Sch 517 Preparing your battery to be charged It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the volt/amp selector switch to match the voltage rating of the battery to be charged.
8 Sch 517 Using Y our Bat ter y Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
9 Sch 517 The “START” area of the ammeter indicates a high rate of current being drawn by the battery. For example, when cranking an engine, the needle will be at the far right side of the “START” area since the starter will be drawing up to 225 amps from the charger.
10 Sch 517 Charging your battery Charging your battery in the vehicle: 1. Arrange the power cord and charging cords care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
11 Sch 517 Charging your battery outside the vehicle: 1. Remove battery from vehicle, making sure to dis- connect grounded terminal first with all power turned off to the vehicle. REMEMBER: A marine battery should be removed and charged on shore unless special equipment designed for marine use is available.
12 Sch 517 15 AMP NR NR 1½ - 2 2 - 2½ 2½ - 4½ 2½ 3½ 4 4½ 2 AMP 2 - 4 4 - 10 11 - 14 14 - 18 18 - 35 18 27 30 33 Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge.
13 Sch 517 Using the engine start feature Your battery charger can be used to jump start your car if the battery is low. Follow these instructions on how to use the engine start feature.
14 Sch 517 If the above solutions do not eliminate the problem... call toll-free from anywhere in the U.S.A. 1-800-SEARS-64 (1-800-732-7764) 7 am to 4:30 pm CST Monday through Friday POSSIBLE CAUSE Clamps are not making a good connection. 2 amp charge rate is being used.
When requesting service or ordering parts, always provide the following information: • Product T ype • Model Number • Part Number • Part Description OWNER’S MANUAL Model No.
An important point after buying a device Sears 200.71450 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 200.71450 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 200.71450 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 200.71450 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 200.71450 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 200.71450, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 200.71450.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 200.71450. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 200.71450 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
