Instruction/ maintenance manual of the product 200.713101 Sears
Go to page of 16
OWNER'S MANUAL DieHard 10/2/60 AMP FULLY AUTOMATIC BATTERY CHARGER ENGINE STARTER Model No. 200.713101 CAUTION: Before first use of charger, read this manual, and follow all its Safety and Operating Instructions with every charger use. Save these instructions.
WARRANTY ............................................................................................................... 2 SAFETY ..................................................................................................................... 3 Important Safety Instructions .
WARNING: To reduce the risk of explosion, explosive gases, or injury while using your battery charger, follow the precautions listed below: • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery.
Personal Safety Precautions For your own personal safety, please follow the following precautions: • Wear complete eye and clothing • Remove all personal metal items protection when working with lead- acid batteries.
It is important to understand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery for charging. ASSEMBLINGYOURCHARGER Included with your battery charger are two cord wrap posts for storage of the clamp cables.
It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the selector switch to match the voltage rating of the battery to be charged.
Charge Type: • Use the MANUAL setting only if you check the charging progress frequently. The charger will not stop charging when the battery reaches full charge, possibly damaging the battery it left on too long. You must monitor and unplug the charger when battery is fully charged.
• When using AUTOMATIC charge rates, the LED will cycle on and off indicating the charger is maintainingthe battery's state-of-charge. CHARGING YOUR BAI-I'ERY Charging your battery inside the vehicle: .
Charging your battery outside the vehicle: . Remove the battery from vehicle, making sure to disconnect grounded terminal first with all accessories and lights turned off in the vehicle. . Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -).
Your battery charger can be used to jump start your car if the battery is low. Follow these instructions on how to use the ENGINE START feature. 1. Connect the charger to the battery and vehicle as instructed in the "Charging your battery"section on page 8.
Battery Rating Method Use the following table to more accurately determine the time it will take to fully charge a battery that is initially at 50% State-of-Charge. Identify you r battery type and its associated Charge Time in the table. Common battery types are: • Small batteries, motorcycles, garden tractors, etc.
Charge Time Needed if Amp-Hours is Known • Find the Charge Factor for your battery in the table on page 11. • Multiply by the Amp-Hour rating of the battery. • Divide by the Charger Setting (either 2 Amp or 10 Amp.) • Multiply by 1.25 to get the approximate Hours Neededto bring the battery to full charge.
Performance problems often result from little things ahat you can't fix yourself. Please read through this chart for a possible solution if a I PROBLEM POSSIBLE CAUSE No ammeter reading. Clamps not making good connection. Circuit breaker in charger cycles on and off with a clicking sound in the MANUAL setting.
This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Item Description Part Number 1 Transformer 93026484.
BRN 15.
For information about troubleshooting Call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CST Monday through Friday 1-800-732-7764 (1-800-732-7764) For the repair or replacement parts you need .
An important point after buying a device Sears 200.713101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 200.713101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 200.713101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 200.713101 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 200.713101 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 200.713101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 200.713101.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 200.713101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 200.713101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
