Instruction/ maintenance manual of the product 200.71233 Sears
Go to page of 15
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 50/15/2 Amp Manual ENGINE ST AR TER With Batter y T ester and Air Compressor 225/125 Amp 00-99-000538/0506 O WNER’S MANU AL Model No. 200.71233 CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.
1 W arranty .................................................................... 1 Important Safety Instructions ................................. 2 P arts .......................................................................... 3 Wiring Diagram ...
2 Help us help you REMEMBER: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging.
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like.
4 Attach Foot: Remove charger from packing materials and place charger face down. Attach mounting foot and secure with the two, 1/4-20 thread cutting screws provided. continued on next page Before Using Y our Battery Charger It is important to prepare your charger for use.
5 Axle Assembly (continued) : Place the charger on its side. Place one end of each bracket into slot, then place the axle assembly under each bracket. Fasten the other side of each bracket using the two, 10-32 thread cutting screws provided. WARNING Plugging it in Electrical Shock Hazard Be sure that power cord fits properly into outlet.
6 MINIMUM RECOMMENDED EXTENSION CORD Length of Cord, in Feet 25 50 100 150 AWG* Size of Cord 16 14 10 8 *AWG=American Wire Gauge Using an e xtension cord The use of an extension cord is not recommended.
7 To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Using Y our Battery Charger Follow these instructions to obtain the accurate charge level for your battery.
8 12V ALTERNATOR/GENERATOR DISPLAY 14 – 15 volts = Good condition 12.8 or less volts = Check with qualified technician 12.8 - 14 volts or = See vehicle owner’s 15 volts or more manual NOTE: If the digital display reads less than 12.8 volts, the charging system may have loose fan belts, a defective voltage regulator or alternator.
9 Using the engine start feature The Engine Start is a feature to help start the engine of your vehicle: 1. Push the switch located on the front panel to CHARGE/TEST.
10 Charging Y our Battery NO TE: A marine (boat) boat batter y must be remov ed and charged on shore. T o charge it on board requires equipment specially designed for marine use.
11 Charging your battery outside the vehicle: NO TE: A marine (boat) must be remov ed and charged on shore. T o charge it on board requires equipment specially designed f or marine use. 1. Remove battery from vehicle, making sure to dis- connect grounded terminal first with all power turned off to the vehicle.
12 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED . Find your battery’s rating on the chart below and note the charge time given for each charger setting.
13 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs.
14 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764).
An important point after buying a device Sears 200.71233 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 200.71233 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 200.71233 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 200.71233 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 200.71233 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 200.71233, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 200.71233.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 200.71233. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 200.71233 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
