Instruction/ maintenance manual of the product 200.71231 Sears
Go to page of 14
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 40/2 Amp Manual 200 Amp ENGINE ST AR TER 00-99-000312/0306 Model No. 200.71230 O WNER’S MANU AL CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.
1 W arranty .................................................................... 1 Important Safety Instructions ................................. 2 P arts .......................................................................... 3 Before Using Y our Batter y Charger .
2 Help us help you Remember: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging.
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List DieHard 71230 Wiring Diagram Item Description Part Number 1. Handle 3599000286 2.
4 To attach the axle assembly: 1. Remove charger from packing materials and place upside down on a flat surface. Attach mounting foot and secure with the two 1/4-20 thread cutting screws. 2. Hold axle upright on floor or work surface. Then, using a hammer, tap one of the plastic hubs onto the top end of the axle.
5 3. Place the charger on its side. Place one end of each bracket into slot, then place the axle assem- bly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided. To attach the handle: Turn the charger right side up onto its foot and wheels.
6 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician.
7 To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Using Y our Battery Charger OFF 40A 12V CHARGE 2A 12V CHARGE 200A 12V ENGINE START All the controls for your charger are located on the front of the unit.
8 Charging Y our Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
9 Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all power turned off to the vehicle. 2. Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -).
10 2 AMP 2 - 4 4 - 10 11 - 14 14 -18 18 - 35 18 27 30 33 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED. Find your battery’s rating on the chart below and note the charge time given for each charger setting.
11 A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger.
12 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check f or poor connections to battery and fr ame.
13 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764).
An important point after buying a device Sears 200.71231 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 200.71231 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 200.71231 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 200.71231 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 200.71231 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 200.71231, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 200.71231.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 200.71231. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 200.71231 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
