Instruction/ maintenance manual of the product 113.24611 Sears
Go to page of 24
Sears CAUTION: Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefu|iy COMMERCIAL 15-I/2 INCH DRILL PRESS assembly operating repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. and SIMPSONS-SEARS LIMITED, Toronto, Ontario, Canada.
general safely instructions for power tools 1. KNOW YOUR POWER TOOL Read the owner's manual carefully. Learn its application and limitations as well as the specific potential hazards peculiar to this tool. 12. USE SAFETY GOGGLES Safety goggles must comply with ANS Z87.
WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT.TO OPERATE YOUR DRBLL PRESS UNTIL IT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDgNG TO THE iNSTRUCTIONS ... AND UNTIL YOU HAVE READ AND UNDERSTAND THE FOLLOWING: 1. General Safety Instructions for PowerTools .
additional safety 11. Note and Follow the Safety Rules that Appear on the Panel on the Left Side of the Head: l DANGER: FOR YOUR OWN SAFETY: READ AND UNDERSTAND OWNERS MANUAL BEFORE OPERATING THIS MACHINE. WEAR SAFETY GOGGLES. DO NOT WEAR GLOVES. SECURELY CLAMP WORK TO TABLE IF IT IS TOO SHORT TO CONTACT THE COLUMN WHEN IN OPERATING POSITION.
motor specifications and eJectricaJ requirements MOTOR SPECIFICATIONS This drill press is designed to use a 1725 RPM motor only. Do not use any motor that runs faster than 1725 RPM. It is wired for operation on 1t0-120 volts, 60 Hz., alternating current.
assembly WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. 1. Unwind the power cord. 2. Make sure the quill lock handle is tight. 3. Stand on the left side of the drill press and LOOSEN the HEAD LOCK HANDLE.
2. Apply a light film of oil such as Sears household oil to the spindle nose. 3. Place the chuck on the spindle nose and screw the locking collar up as far as it will go. CHUCK 4. 5. Insert a piece of 5/16 in. dia. STEEL ROD in to one of the holes in the chuck body.
assembly INSTALLING THE DEPTH STOP 1. Screw the THUMB SCREW partways into the DEPTH POINTER. 2. Place the DEPTH POINTER SHOE inside the pointer. 3. Loosen QUILL LOCK HANDLE ... lower the quill about two inches. 4. 5. 6. Slide the pointer and shoe onto the FEED STOP ROD and tighten the thumb screw.
9.Gently push down on the FEED HANDLES untilthe head raises upwards as faras it will go. DO NOT RELEASE FEED HANDLE. 10, TIGHTEN THE HEAD LOCK HANDLE AND THE QUILL LOCK HANDLE. 11. HOLD onto the Feed Handle andUNLOCK the quill lock handle. 12. Let the quill return to the UP position in the head, 13.
assembly 4. 5, NOTE: When using motors which have 1/2 in. dia. shafts, place the adapter sleeve (furnished with the motor) on the shaft so that the slot in the sleeve is over the flat spot.
5, Remove the belt guard by "pushing in" on the two "'links". 6. Place motor on drill press ... screw the pivot screws into the holes. NOTE: DO NOT SCREW THEM IN TOO TIGHT ... EXCESSIVE TIGHTNESS COULD BEND THE MOTOR MOUNT. i 7.
assembJy iNSTALLING AND TENSIONING BELT 1. Place a straightedge such as a piece of wood, metal or framing square across the pulleys. 2. Move the motor UPWARDS until the pulleys are IN LINE ... tighten the motor mounting nuts with a ½ in. wrench. 3. Place the belt on the pulleys.
getting tO kr ow SPLINES (GROOVES) SPINDLE QUILL _ RACK (TEETH) CHUCK __-_ CHUCK KEY _ QUILL AND SPINDLE ASSEMBLY INSIDE OF DRILL PRESS SPINDLE SPEED CHART 9 CHUCK KEY ... is used to tighten or loosen the chuck. It has a spring loaded EJECTOR pin to "pop'" it out of the chuck when you let go of it.
getting to know your drill press To turn drill ON .. Insert finger under switch lever and pull. TO turn drill OFF ... Push lever in. In an emergency; ...thedrill bit BINDS ...STALLS .. STOPS . .. or tends to tear the workpiece loose . .. you can QUICKLY turn the drill OFF by hitting the switch with the palm of your hand.
_{_ The DEPTH POINTER is locked in place with the THUMBSCREW. !_ L FEED STOP NUT limits the downward movement of the quill at any desired point within its travel, and prevents the pointer from moving upward. DR! LLING TO DEPTH To drill a BLIND hole (not all the way through) to a given depth, can be done two ways.
basic drill press operation INSTALLING DRILLS Insert drill into chuck far enough to obtain maximum GRIPPING of the CHUCK JAWS ... the jaws are appox. 1 in. long. When using a small drill do not insert it so far that the jaws touch the flutes (spiral grooves) of the drill.
diustments WARNeNG: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. DEPTH SCALE When the quill is in the UPPERMOST position, the top SURFACE OF THE FEED STOP POINTER should be in line with "0" graduation on the DEPTH SCALE.
adiustments 5. LOOSEN all three screws "C", "D", and "E'" four turns using 1/4 in. setscrew wrench. NOTE: TIGHTENING BOTH SCREWS "C'" AND "E'" SQUEEZES HEAD TOGETHER ... TIGHTENING SCREW "'D" SPREADS IT APART.
trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTaNG. TROUBLE Noisy Operation Drill Burns. Drill leads off... I hole not round. t Wood splinters on underside.
6O PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.2461! 68 30 64 T_IO 1 8 13 14 SEE FIGURE 2 11 12 I J ALL WIRES TO SNAP INTO WIRE SADDLE _ I--.83 _.
Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 78 79 :0 7 2 3 4 5 6 7 8 9 0 1 2 3 4 Part No. 70197 STD 541110 71046 STD 571812 71163 STD 551210 STD 551208 STD 600605 7.
PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS S MODEL No. 113.24611 . . __ FIGURE 2 PARTS LIST Key Part No. No. ,_, r = 71128 12 144987 4 71069 5 STD 610807 13 6 60158 7 71071 8 71070 71162 1_] 71072 14 11 71097 12 60227 13 71089 11_ 14 71090 15 STD 315253 15---"--_ 16 71091 16.
/ / / / t PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS MODEL No. 113.24611 / / / ,/ / / 1, / / / / / 10---_ 11 / FIGURE 3 -- 71158 SPINDLE ASM. STOP PARTS LIST Key Part No.
Sears SERVICE MODEL NO. 113.24611 HOW' TO ORDER REPAIR PARTS COMMERCIAL 15-1/2 INCH DRILL PRESS Now that you have purchased your drill press, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
An important point after buying a device Sears 113.24611 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 113.24611 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 113.24611 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 113.24611 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 113.24611 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 113.24611, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 113.24611.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 113.24611. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 113.24611 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
