Instruction/ maintenance manual of the product 113.21308 Sears
Go to page of 28
Save This Manual r Future Reference MODEL NO, !t3.2!3080 DRILL PRESS WITH MAXIMUM DEVELOPED I/3 HP MOTOR Serial Number Model and serial number may be found at the rear of the head. You should record both model and serial number in a safe place for future use.
FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SER- VICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
additional safety instructions for driJl presses _VARNING: FOR YOUR OWN SAFETY, DO NOT _,TTEMPT TO OPERATE YOUR DRILL PRESS JNT_L RT _S COMPLETELY ASSEMBLED AND IN- STALLED ACCORDING TO THE INSTRUCTHONS... _ND UNTIL YOU HAVE READ AND UNDERSTAND THE FOLLOWING: 1.
b. Drum sanders must NEVER be operated on this driU press at a speed greater than 1800 RPM c. Do not install or use any drill that exceeds 7" in length or extends 6" below the chuck jaws, They can suddenly bend outward or break. d. Do not use wire wheels, router bits.
gJossary of terms !. Workp_ece The item on which the cutting operations is bei_g performed. 2. O_igl The cutting tool used ir_ the dritt press to make hoies in a workpiece. 3. Backup Material A piece of wood piaced between the workpiece and table ....
meter specifications and e ectricaJ requirements MOTOR SPECIFmCATmONS This drill press is designed to use a 1725 RPtvl motor only. Do not use any motor that runs faster than t725 RPM. It is wired for operation on 110-120 volts, 60 Hz. alternating current.
unpacking and checking contents WARNING: TO AVOID INJURY FROM UNEX- PECTED STAF_TING OR ELECTRICAL SHOCK, DO NOT PLUG THE POWER CORD iNTO A SOURCE OF POWER. THiS CORD MUST REMAIN UNPLUG- GED WHENEVER YOU ARE WORKING ON THE DRILL PRESS. Model 113.213080 Drill Press is shipped complete in one box.
List of Loose Parts in Box 507870 Item Description Qty. A Chuck Key .......................... 1 B Chuck. ............................. 1 List of Loose Parts in Bag 507871 Item Description Qty. A Feed Handle ........................ 3 B Wrench Hex "L" 4rnm .
location and function of controls 1. BELT GUARD... Covers pulleys and belt during operation of drill press, 2. BELT TENSION LOCK HANDLES... Tightening handles locks motor bracket support to maintain correct belt distance and tension. 3. HEAD LOCK SET SCREWS.
assembly WARNING: FOR YOUR OWN SAFETY, NEVER CON- NECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. TOOLS NEEDED '[' _ .... I f' '1" I' .I, • ], I,'I. I • , , MEDIUM SCREWDRIVER COMBINATION SQUARE 8-INCH ADJUSTABLE WRENCH DRAW LIGHT LINE ON BOARD ALONG THIS EDGE _.
. 4. Locate support lock handle among loose parts. Install support lock handle from left side into table support. Raise table to working height by sliding it on the column and then tighten lock handle by hand. TABLE SUPPORT COLUMN TABLE iNSTALLiNG THE HEAD CAUTION: The head assembly weighs about 45 pounds.
iNSTALLiNG FEED HANDLES !_ Locate three (3) feed handles among Iooseparts. 2 Screw the feed handles tightly into the threaded hotes in the hub. iNSTALLING THE CHUCK 1, Locate the chuck among loose parts. 2, Clean out the TAPERED HOLE in the chuck; clean the spindle nose with a clean cloth.
BELT GUARD KNOB 5ram DIA. x 12ram LONG SCREW iNSTALLING BELT GUARD KNOB BELT GUARD KNOB 1, To attach belt guard knob, locate knob and 5mm Dia x 12ram _ong pan hd screw in toose parts bag. Insta!! screw in hote iocated in guard and attach knob turning until tight.
ADJUSTING THE TABLE SQUARE TO HEAD NOTE: The combination square must be "true." See the beginning of the "Assembly" section for a method to check four square. 1. Insert precision round steel rod approximately 3" tong into chuck and tighten.
getting to know press 1 BELT GUARD / 15 FEED HANDLE FEED SPRING ADJUSTMENT 19 ON-OFF SWITCH FEED SPRING 9 DEPTH POINTER 16 CHUCK 2 BELTTENSION LOCK HANDLE 3 HEAD LOCK SET SCREWS 4 TABLE SUPPORT 18 STOP NUTS 14 TABLE COLUMN COLUMN SUPPORT _ IO.
This Drill Press has 3 speeds as listed below: 620 RPM ! 300 RPM 31OORPM See inside of beltguard for specific placement of belts on pulleys. SPINDLE SPEEDS BN R.P.M. 1, BELT GUARD .... Covers pulleys and belt during operation of drill press. 2. BELT TENSION LOCK HANDLE .
Insert KEY into switch. NOTE: Key is made of yellow piestico 1 To turn drill ON . . . Insert finger under switch lever and pull. To turn drill OFF.,. Push lever in. In an emergency;.. , the drill bit BINDS... STALLS •.. STOPS ., . or tends to tear the workpiece loose •.
REMOVING THE CHUCK 1. Open jaws of chuck as wide as they will go by turning chuck sleeve. 2. Carefully tap chuck with mallet in one hand while holding chuck in other hand to prevent dropping it when released from spindle nose, SLEEVE DRILLING TO DEPTH To drill a BLIND hole (not all the way through) to a given depth, can be done two ways.
basic dr!IS press operation Follow the following instructions for operating your drill press to get the best results and to minimize the likeli- hood of personal injury. WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE SAFETY PRECAUTmONS HERE AND ON PAGES 2, 3, AND 4.
POSITiONiNG TABLE AND WORKPIECE Lock the table to the column in a position so that the tip of the dritl is just a little above the top of the work- piece. Always place a piece of BACK-UP MATERIAL (wood, plywood...) on the table underneath the workpiece.
WARNING: TO AVOID iNJURY FROM SPiNNiNG WORK OR TOOL BREAKAGE, ALWAYS CLAMP WORKPmECE AND BACKUP MATERIAL SECURELY TO TABLE BEFORE OPERATING DRILL PRESS WITH THE TABLE TILTED. To return table to original position: loosen the bevel lock, tilt table back to 0 ° on bevel scale, and retighten bevel lock.
maintenance WARNING FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUB- RiCATiNG YOUR DRILL PRESS. Frequently blow out any dust that may accumulate in- side the motor. A coat of furniture-type paste wax applied to the table and column will help to keep the surfaces clean.
trouble shooting WARNSNG: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE "TROUBLE SHOOTING. ® CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN TROUBLE Noisy Operation Drill Burns Drill leads off.
33 PARTS LIST FOR CRAFTSMAN 8" DRILL PRESS MODEL NO. 113.213080 34 ='O mo "O 3O 29 28 27 26 16 24 17 18 15 19 20 FIGURE 1 1 / 7.
r,o ¢jn PARTS LiST FOR CRAFTSMAN 8" DRILL PRESS MODEL NO. 113.213080 Always order by Part Number--Not by Key Number FIGURE 1 Key J Part No. I No.
repair parts PARTS LiST FOR CRAFTSMAN 8" DR_LL PRESS MODEL NO. 113.213080 2 14 Always order by Part Number--Not by Key Number FIGURE 2 Key Part No. No. 1 817451-1 2 817325 816755-3 817428 5 817779 6 817358 7 8!7453-1 Description Bushing-Rubber Knob Screw-Pan Hd, M5 x 0.
repair parts PARTS LIST FOR CRAFTSMAN 8" DRILL PRESS MODEL NO. 113.213080 I 1 fl 2 j2 Always order by Part Number--Not by Key Number FIGURE 3 QUILL ASSEMBLY Key Part No.
f SERVICE MODEL NO. !t3.2t3080 DREL PRESS WITH MAXIMUM DEVELOPED I/3 HP MOTOR HOW TO ORDER REPAIR PARTS i.i. L Now that you have purchased your 8-inch Drill Press, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
An important point after buying a device Sears 113.21308 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 113.21308 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 113.21308 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 113.21308 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 113.21308 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 113.21308, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 113.21308.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 113.21308. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 113.21308 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
