Instruction/ maintenance manual of the product 113.20680 Sears
Go to page of 32
.... :/i "< i ¸ MODEL NO. ]]3.20680 JOINTER/PLANER ONLY 113.206930 JOINTER!PLANER WITH LEGS AND MOTOR Serial Number ....................................... Model and serial number may be found on a plate attached to your infeed table. You should record both model and serial number in a safe place for future use.
FULL ONE YEAR WARRANTY ON CRAFTSMAN JOINTER/PLANER year from the date of purchase, this Craftsman Jointer/Planer fails due to a defect in material rs will repair it, free of charge. ,VAtLABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES.
Safety is a combination O f operator common sense and alertness at all times when the Jointer-Planer is being used. WARNING: FOR YOUR OWN SAFETY, DO NOT AT- TEMPT TO OPERATE YOUR JOINTER-PLANER UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS, .
Safety instructions 13,:To be sure you will make adepth of cut as planned, always lower tl_e infeed table slightly beyond the depth Wanted. then raise the table to the desired depth. 14. When _aning, jointing, orl beveling wood over four {4) feet :long, make.
o • _ • ee motor spec faCahons and e ectrmcalrequmrements Th_is machine is designed to use a 3450 RPM moto_ only Do not use any motor that r._r_s faster' than 3450 RPM, It is wired for operation on t10-t20 vo_ts, 60 Hz. _dter- nating current.
: 3/4,:'Wrench : : :_. :. :3/8_,Wrench : i::: i: : : :::i: : ::_ : _ ....... Model t13.20680 JointeriPlaner iS shipped ¢_mplete 'one. cartOn, but DOES NOT INCLUDE Stee| Legs. motori ..... ..... ...... in or Model t13.206930 Jointer/Planer is shipped comp!lete in one carton but INCLUDES Steel Legs, and Motor.
unpacking Qnd checking TABLE OF LOOSE PARTS The Following Parts Are Included With Model 113.206930 Only Item No. Description Qty. A Leg .............................. 4 B End Stiffener ........................ 2 C Side Stiffener ......................
MOUNTING JOINTER:PLANER hardware:- 4 Carriage 8ott,: 5./16_18 x 3/41 3 Hex Head: screws,: 5/16_18 X:2 7 Lockwashers, 5/i6 in. EXternal Type 7 Washers, 11t32 1D 7 Hex Llam Nuts, 5/16-18 2 Cord Clips the following t. Loosen FENCE LOCK KNOB. Tilt fence upward and slide it toward the pulley.
iNSTALLING SLIDING GUARD PARTS NEEDED 1 Sliding Guard I Sliding Guard Knob t Sliding Guard Rod 2 Sliding Guard Washers (one side of washer is concave) 1 Hex. Nut 1/2 in.* t3 1 Sl_it lockwasher 1/2 in. 2 E×t, tooth Iockwashers 2 10-32xl/4 Pan Hd. Screws t.
¸ C_i _:!:iin:motoK pdiley and:place:Pulley:iOn h_ f|U_h:! _itt+ end i: sfiaf_ii ihSertl motif:r: The motor rn_:$ _iewed from +PULLEY end: 1_ Place m0tor on your workbench or on floor. 2. Stand clear of motor and plug cord into a properly grounded outlet (See page 5).
8. Snap guard into position as shown. 9. Remove knob and washer.., lift guard up. 10. Loosen the two MOTOR BASE CLAMP SCREWS and rotate the motor so that the ventilation slots are facing downward, tighten base clamp screws.
i ¸ • :Q • •• :••• • • know our olnter- maner .... .... P WARNING: F_R" YOUR OWN: SAFETY TURN SWITCH 2 SLIDING GUARD INFEED TABLE SLIDE BRACKET CUTTER GUARD 6 ON-OFF SWITCH IIII ! _1 L I 1 11: DEPTH OF CUT HANDWHEEL.
b. Before tightening fence lock knob, hold fence down on outfeed table so it does not rock. c. 90 ° Fence Stop positions fence square to tables. To tilt fence, loosen the two knobs .and pull the sto;p out. Tilt to desired angle and tighten both knobs.
tO know your 'Ointer-manet I ..... P HEAD OF SQUARE FENCE INFEED TABLE ::e. Adjust 450 stop in the same manner. NOTE: Tilt scale will not require adjustment if it was= adjusted foi _ 90 ° position. 4, CUTTER GUARD. Provides protection over the cutter head.
a. b, :!:'/i _I _ :i _ _:i?_i; _: _:::' :::i, _:: : i: :_:_ ::i:/ ::ii: :!;_:i::::}::i_ I :_i _:_ :/!: :: : :: Insert a pencit in space at end of cutterhead to hold cutterguard open. Place a straightedge (large square or tong level) on outfeed table.
toknow: your io nter planer :': i_: _ : : . ........ ..... : L0osen foUr:ioCk Screws 2:or: 3 turns with 1/2 in. Wrench; LEVELING STUDS I LOCKSCREWS VIEW LOOKING UP FOR PARTS IDENTIFICATION Turning the' LEVELING STUDS will RAISE or LOWER the infeed table.
_ i ! i:: !_ i b, To turn machine on, insert finger under switch lever and pull end of switch out. c, To turn machine OFF... PUSH lever in, Never leave machine unattended until it has come to a complete stop. d. To lock switch in OFF position,,, hold switch IN with one hand.
_i -_ • • - ,., For your own safetY:, ALWAYS use the hold down/push bi0cks.when JOiN_lNGw0od thai_ is NARROWER than 3in.. !:.o_ whenP LANt NG:w00d: that is THIN NE R than 3 in: Do not plane, joint 0r bevel wood shorter than 12 in, Material this short is more difficult to control while being cut.
: :_ _:_ i_ _: ,i : Always feed WITH THE GRAIN whenever possible. If the nature of the workpiece is such that it must be fed AGAli_ST THE GRAIN, take very light cuts and feed slowly.
when pianing wood 3/4 in, thick and NARROWER than the holdldownipush b!ock_ tilt the h0td d0wn/push block so that it clea_s"the top of the cutterguard while #eeding.
rnainfenance REPLACING CUTTER BLADES WARNING:FOR YOUR OWN SAFETY. TURN SWITCH "OFF"AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE ADJUSTING, MAINTAIN- ING, OR LUBRICATING YOUR JOINTER-PLANER. t. Remove belt guard. 2. Position fence to right .
maintenance 5/32 IN. SETSCREW: WRENCH 7*: Remove :the six lifter screwsi (Two under each blade.) 8_ C!ean cutterhead,:wedges and screws thoroughly with = craftsman Gum and Pitch Rem0ver. A!_o remove the oil from dew blades, 9; Replace the six lifter screws and screw them in all the way, but do not tighten.
INSTALLING CUTTER GUARD SPRING 1. Remove cotter pin from pivot pin in cutter guard and remove guard (located underneath infeed table.) Spring must appear as in sketch from underside of in- feed table, it will not perform properly if installed upside down.
The normal position of guard {at REST) when fence is Stati0nedat MAXIMUM WIDTH OF CUT; is shown as ........ • ..... EY ND postlon A NEVER ROTATE GUARD B O POS|TION"B" BECAUSE THIS WOULD EXERT EX- CESSIVE TENSION ON SPRING WHICH COULD WEAKEN OR BREAK IT, Check Operation of GUARD and SPRING.
generaB maintenance Keep your jointer-planer clean. Put a carton or some kind of a container underneath your iointer-ptaner to catch the chips. The container should reach above the top of the motor. Do not allow pitch to accumulate on the tables, the fence, the cutter guard, the cutter head or the knives.
WARNING: FOR:YOUR::OWN SAFETY, :TURN SWITCH ',OFF.: AND _ REMOVE:: PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING YOUR JOIN_ TROUBLESHOOTING CHART ,_ TROUBLE ,,,,,,,,,, _ , PROBABLE CAUSE, REMEDY Motor will not run. 1. Defective On-Off switch.
FIGURE 1 1 7 2 K N 3 4 5 6 7 8 9 10 FIGURE 1 - LEGS PARTS LIST .=y Part o. No. 1 67033 2 60314 STD55t225 STD541025 67032 62614 62204 67034 STD541250 803835 Description Stiffener, End o *Screw, Truss Hd. 1/4 - 20 × 5/8 o *Lockwasher, 1/4 External • *Nut, Hex 1/4 - 20 Stiffener, Side Leg m Clip, Cord Support, Motor o'Nut, Hex Hd.
i0 oo CRAFTSMAN 6-1!8 tNCH JOINTER-PLANER MODEL No, 113.20680 AND 113,206930 50 --49 49 SEE FIGURE 4 FOR EXPLODED VIEW ........_ 3 8 7 9 48 11 1o 16 12 45 43 5 7 44 FIGURE 2 42 39 18 39 37 38 _r_SWITCH BOX ASSEMBLY .
CRAFTSMAN 6-1/8 INCH JOINTER-PLANER MODEL No. 113.20680 AND 113.206930 £o FIGURE 2 PARTS LIST :•Key ........... No. i Part No. i"8437 21013 67020 21622 STD582062 1844t 3509 38879 60345 62023 STD503103 STD522505 67008 STD541025 STD304520 30646 60252 STD601105 60253 60254 67031 60255 37887 60O96 455872 63410 67016 Description w ;hers .
pair, parts !CRAFTSMAN 6-1/8 iNCH 3OtINTER-PLANER MODEL No. 113.20680 AND 113.206930 ! / / / 2 FIGURE 3 5 21 ' 22 23 Key No. 1 2 3 4 5 6 7 8 9 t0 11 : 12 FIGURE 3 INFEED TABLE PARTS LIST Part No. STD 561210 67015 67014 STD511107 STD551210 STD551010 38779 67011 67012 STD522505 STD551025 : 1 21812 Description Pin, Cotter, 1/8.
CRAFTSMAN 6-118 INCH JOINTER-PLANER MODEL No. 113.20680 AND 113.206930 1 2 3 4 5 6 7 10 11 12 FIGURE 4 Key Part No. No. 21013 1 21440 2 21430 3 STD 522512 4 21232 5 21736 6 STD551010 7 STD510802 10281.
_ • ..... : ....... ::< iii ! /:••• • :3 • i....... • : /v • Sears SERVmCE MODEL NO. ]!3.20680 JOINTER/PLANER ON LY 113.206930 JOtNTER/PLAN ER WITH LEGS AND MOTOR HOW TO ORDER REPAI.
An important point after buying a device Sears 113.20680 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 113.20680 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 113.20680 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 113.20680 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 113.20680 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 113.20680, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 113.20680.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 113.20680. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 113.20680 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
