Instruction/ maintenance manual of the product X330W-2DS1 Avaya
Go to page of 16
A vaya X330W -2DS1 Access Router Module Quick Start Guide N N o o t t e e : The X330W AN expansion modules can be installed in the following A vaya P330 switches: • P333T , P334T , P332MF , P333R, P333R-LB, P333T -PWR – Embedded S/W version 3.
Important Safety Information Before installing or r emoving any components of a device, or carrying out any maintenance work, you must read the safety information pr ovided. CAUTION: T o avoid damage from static, only hold the W AN Expansion Router Module by the edges.
Unpack the Module Check the package contents for the following: Equipment • One X330W AN Access Router Module. L Connection cables are not supplied. Documentation • A vaya X330W AN Access Router Modules Quick Start Guide (this document). • A vaya X330W AN Access Router Modules Release Notes.
Insert the Module T o insert an X330W AN into an A vaya P330 switch: 1. Remove the blanking plate or other expansion module (if installed). 2. Insert the W AN expansion module gently into the slot, ensuring that the Printed Circuit Board (PCB) is aligned with the guide rails.
4 Connect the Ports Connecting the E1/T1 Ports T o connect a T1/E1 module to a network, use a straight-through RJ-48C-to-RJ-48C cable to connect the E1/T1 port to an RJ-48C wall jack. Connecting the Ethernet Port A UTP Category 5 cable must be connected to the 100Base-TX port, via an RJ45 connector .
5 Configure the Module L Before you can set up the X330W AN module you must power on and set up the A vaya P330 stack as described in the A vaya P330 User ’s Guide. L Before using the X330W AN module you must assign an IP addr ess via the Command Line Interface (CLI) or via a T elnet session to the switch where the X330 is inserted.
L The console interface configured with the interface Console command must be on a differ ent subnet from the r outer interfaces. 6. Use the following commands to set the baud rate, ppp authentication.
Configuring Loopback Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure Loopback interfaces: 1. Use the interface loopback <loopback number> command to enter the Interface Loopback mode.
Configuring E1/T1 Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure E1/T1 interfaces: 1. Use the show controllers command to check if your controller ’s mode is configured as E1 or T1.
Changing the Primary Management Interface (pmi). L The default pmi is the first interface you define. T o change the pmi: 1. Enter one of the interface contexts as explained before. 2. If there no ip assigned on that interface use the | ip address <ip_ addr>< net- mask> command.
X330WAN Default Settings The default settings for the X330W AN and its ports are determined by its embedded software. These default settings are subject to change. Newer versions of the softwar e for the X330W AN can be downloaded from the A vaya Network Software Download W eb site (http://www .
Run the W eb-Based Manager (optional) L T o configure the A vaya X330W AN you can use the P330 W eb-based Manager in addition to using the CLI. System Requirements Minimum hardwar e and Operating Syst.
L If the network manager has configured the system the plug-in should be installed auto- matically . If the plug-in is not installed automatically , there ar e three ways to install the plug-in manually: • Either install the plug-in fr om the CD as follows: 1.
Documentation and Online Help Refer to the A vaya X330W AN Documentation and Utilities CD for full instructions..
Notes.
Contact Information T o contact A vaya technical support: From the United States: Please call 1-800-237-0016, press 0, then pr ess 73300. From outside the United States: EMEA (Europe, Middle East and Africa). Email: csctechnical@avaya.com AP (Asia Pacific).
An important point after buying a device Avaya X330W-2DS1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Avaya X330W-2DS1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Avaya X330W-2DS1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Avaya X330W-2DS1 you will learn all the available features of the product, as well as information on its operation. The information that you get Avaya X330W-2DS1 will certainly help you make a decision on the purchase.
If you already are a holder of Avaya X330W-2DS1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Avaya X330W-2DS1.
However, one of the most important roles played by the user manual is to help in solving problems with Avaya X330W-2DS1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Avaya X330W-2DS1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
