Instruction/ maintenance manual of the product AL1916 Acer
Go to page of 16
1 English Table of Contents Preface ............................................................................................................................... 2 FCC Statemen t Warning ..............................................................
2 Preface This manual is designed to assist users in setting up and using the LC D Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to cha nge without notice.
3 Important Safety Instructions Please read the following instructions carefully. Th is manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag.
4 IT Equipment Recycling Information IT Equipment Recycling I nformation: Acer is strongly committed to environmental protecti on and views recycling, in the form of salvaging and disposal, of used equipment as one of the company’s top priorities in minimizing the burden placed on the environment.
5 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suita ble workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow.
Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.
7 Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or o ff. The other control buttons are located at front panel of the monitor (See Figure 2-1). By changing th ese settings, the picture can be adjusted to your personal preferences.
8 Front Panel Control / Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. Power Indicator: Green — Power On mode.
9 How to Adjust a Setting 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function.
10 N/A English N/A Deutsch N/A Français N/A Español N/A Italiano N/A 繁體中文 or Русский N/A 简体中文 or Hollands N/A 日本語 or Suomalainen Multi-language selection. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertical position of the OSD.
11 Chapter 3 Technical Information Specifications LCD Panel Size 19" Display Type Active matrix color TFT LCD Resolution 1440 x 900 Display Dot 1440 x (RGB) x 900 Display Area (mm)(H x V) 408 x 255 Display Color 16.
12 Power Management Mode Power Consumption* AC Input LED Color On 55W maximum 240 VAC Green Off 2W maximum 240 VAC Amber Soft switch off 1W maximum 240 VAC Dark * Meeting VESA DPMS requirements measured from AC Input end of AC power cord.
13 Pin Assignment Signal PIN Description PIN Description PIN Description 1 2 3 4 5 Red Green Blue Digital GND Digital GND 6 7 8 9 10 Red Rtn Green Rtn Blue Rtn +5V Hot Plug Detect 11 12 13 14 15 NC SDA H.
14 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the m ost suitable available timing. TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 640x350 31.
15 TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 800x600 46.875 + 1056 800 80 16 160 49.5 VESA-600-75Hz 75 + 625 600 3 1 21 1024x768 48.363 – 1344 1024 136 24 160 65 XGA 60.
16 Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market , users may initially experience an unstable or unclear display whenever a new displa y mode or new VGA card is selected.
An important point after buying a device Acer AL1916 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Acer AL1916 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Acer AL1916 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Acer AL1916 you will learn all the available features of the product, as well as information on its operation. The information that you get Acer AL1916 will certainly help you make a decision on the purchase.
If you already are a holder of Acer AL1916, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Acer AL1916.
However, one of the most important roles played by the user manual is to help in solving problems with Acer AL1916. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Acer AL1916 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
