Instruction/ maintenance manual of the product ST9500530NS Seagate
Go to page of 46
Product Manual Constellation ® Serial A T A 100538694 Re v . D F ebruary 2011 ST9500530NS ST916051 1NS.
Revision history © 201 1 Seagate T echnology LLC. All right s reserved. Publication number: 1005 38694, Rev . D. February 201 1 Seagate, Seagate T echnology and the W ave logo ar e registered tra demarks of Seagate T echnology LLC in the United S t ates and/or ot her countrie s.
Constellation Serial ATA Product Manual, Rev. D i Contents 1.0 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction . . . . . . . . . . . . . . . . . . . . . .
ii Constellation Serial ATA Pr oduct Manual, Rev. D.
Constellation Serial ATA Product Manual, Rev. D iii List of Figures Figure 1. Typical 5V/12V startup and operation cur re nt profile for ST9500530NS . . . . . . . . . . . . . . . . 12 Figure 2. Typical 5V/12V startup and oper ation cur rent profile for ST9160511NS .
.
Constellation Serial ATA Product Manual, Rev. D 1 1.0 Seagate T e chnology support services SEAGA TE ONLINE SUPPORT and SERVICES For information regarding pr oducts and services, visit http://www .
2 Con stellation Seri al ATA Produc t Manual, Re v. D.
Constellation Serial ATA Product Manual, Rev. D 3 2.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Constellation ® Serial A T A model drives: These drives provide the following key fea t ures: • 7200 RPM spindle speed.
4 Con stellation Seri al ATA Produc t Manual, Re v. D 2.1 About the Serial A T A interface The Serial A T A interface provides several ad vantages over the traditional (p arallel) A T A interf ace. The p rimary advantages include : • Easy installation and configuration with true plug-and-play connectivity .
Constellation Serial ATA Product Manual, Rev. D 5 3.0 Drive specifications Unless otherwise noted, all specific ations are me asured un der ambie nt conditions, at 25°C, and nominal power .
6 Con stellation Seri al ATA Produc t Manual, Re v. D T able 1: Drive specifications summary for 500 and 1 60 GB models Drive specification ST9500530NS ST916051 1NS Formatted Gbytes (512 bytes/sector).
Constellation Serial ATA Product Manual, Rev. D 7 * On e Gbyte equals one billion byte s when referring to h ard driv e capacity. Accessible capacity may vary depending on oper ating environment and formatting. * * During perio ds of drive idle, some offli ne a ctivity may occur accordin g to the S.
8 Con stellation Serial ATA Product M anual, Rev. D 3.2 Formatted cap acity Model Formatted capacity* Guaranteed sectors Bytes per sector ST9500530NS 500 Gb ytes 976,773,168 512 ST916051 1N S 160 Gbytes 312,581,808 *One Gbyte equals one billion bytes when referri ng to hard drive capacity.
Constellation Serial ATA Product Manual, Rev. D 9 3.5 Physical characteristics Weight: (maximum) ST9500530NS 196 grams (0 .43 lbs) ST916051 1NS 18 8 grams (0.41 lbs) Cache buffer 32 Mbytes (32,768 kbytes) Note. Refer to Figure 5, page 23 for det ailed mounting configuration dimensions.
10 Constellation S erial ATA Prod uct Manual, Rev. D 3.8 Power specifications The drive receives DC power (+ 5V or +12V) through a native SA T A power connector . See Figu re 4, pag e 22 on pag e 2 2 . 3.8.1 Power co nsumption Power requirement s for the drives are listed in the tab le on p age 9.
Constellation Serial ATA Product Manual, Rev. D 11 * During period s of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase ac oustic and power to operational levels .
12 Constellation S erial ATA Prod uct Manual, Rev. D 3.8.1.1 T ypical current pr ofiles Figure 1. T ypical 5V/12V startup and operation current profile for ST9500530NS Figure 2.
Constellation Serial ATA Product Manual, Rev. D 13 3.8.2 C onducted noise Input noise ripp le is meas ured at the host sys tem po we r supply across an equivalent 80-ohm resistive load on the +12 volt line or an equival en t 15-ohm resistive load on the +5 volt line.
14 Constellation S erial ATA Pro duct Manu al, Rev. D 3.8.4 Power-man agement modes PowerChoice TM power management Drives using the load/un load architecture provide programm able power management to t ailor systems for per- formance an d grea te r en er g y efficiency .
Constellation Serial ATA Product Manual, Rev. D 15 3.9 Environment al specifications 3.9.1 Ambient tempe rature Ambient temperature is defined as th e temperature of th e envi ronment immediatel y surroundin g the drive. Actual drive c ase temper ature shou ld not ex ceed 60 °C (140°F) within the oper ating ambient conditions.
16 Constellation S erial ATA Pro duct Manu al, Rev. D 3.9.6 Vibration All vibration specifications assume that the drive is mounted secure ly with the input vibration applied at the drive mounting screws. V ibration may be applied in the X, Y or Z axis.
Constellation Serial ATA Product Manual, Rev. D 17 3.10 Acoustics Drive acoustics are meas ured as over all A-weighted ac oustic sound powe r levels (no pure tones). All mea- surements are co nsistent with ISO d o cument 7779. S ound powe r measurement s are taken under essentially free-field conditions over a reflecting plane.
18 Constellation S erial ATA Prod uct Manual, Rev. D 3.12 Reliability 3.12.1 Annualized Failure Rate (AFR) and Mean T ime Between Failures (MTBF ) The product shall achieve an Annualize d Failure Rate - AFR - of 0.73% (Mean T ime Between Failures - MTBF - of 1.
Constellation Serial ATA Product Manual, Rev. D 19 Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, th ey comply with para- graph 1 of Article 1 1 of the.
20 Constellation S erial ATA Pro duct Manu al, Rev. D 3.14 Environment al protection Seagate designs it s products to meet envir onmental pr otection requirement s worldwide, including regulations restricting certain chemical substances.
Constellation Serial ATA Product Manual, Rev. D 21 4.0 Configuring and mounting the drive This section contains the specif ications an d instructions for configuring and mounting the drive.
22 Constellation S erial ATA Prod uct Manual, Rev. D • Install a SATA host adapter th at supports autonegotiation, leave the drive jumper block set to “Normal operation” (see Figure 3, page 22 below) , and connect th e drive to that ad apter. This option has the benefit of not limiting the drive to a 1.
Constellation Serial ATA Product Manual, Rev. D 23 Note. These dimensions conform to the Small Form Factor S tandard documented in SFF-8201 a nd SFF-8223, found at www .
24 Constellation S erial ATA Pro duct Manu al, Rev. D 4.5 Cooling Cabinet cooling must be desig ned by the customer so that the a mbient temperat ure immediately surrounding the drive will not exceed temperatur e conditions specified in Sectio n 3.9.1, "Ambient temperature.
Constellation Serial ATA Product Manual, Rev. D 25 5.0 Serial A T A (SA T A) interface These drives use the industry-s tandard Ser ial A T A interfac e that supp orts FIS data transfers. It supp orts A T A programmed input/o u tput (PIO) modes 0–4; mult iword DMA modes 0–2, and Ultra DM A modes 0–6.
26 Constellation S erial ATA Pro duct Manu al, Rev. D 5.2 Serial A T A device plug conn ector pin definitions Table 5 summarizes the sig nals on the Se rial ATA interface and power co nn ectors. Notes: 1. All pins are in a single row , with a 1.27 mm (0.
Constellation Serial ATA Product Manual, Rev. D 27 5.3 Supported A T A commands The following t able list s Serial A T A standard comman ds that the drive suppo rts. For a detailed descriptio n of the A T A commands, refer to the Serial A T A: High S peed Serialized A T Attachment specification .
28 Constellation S erial ATA Pro duct Manu al, Rev. D Security Erase Unit F4 H Security Freeze F5 H Security Set Password F1 H Security Unlock F2 H Seek 70 H Set Features EF H Set Max Address F9 H Note: Individual Set Max Address commands are identifie d by the value placed in the Set Max Features regis - ter as defined to the right.
Constellation Serial ATA Product Manual, Rev. D 29 5.3.1 Identify Dev ice comma n d The Identify Device command (command code EC H ) tran sfers information about the drive to the host following power up. The da t a is or ganized as a single 512-b yte block of data, whose contents are shown in T able 6 on page 27.
30 Constellation S erial ATA Pro duct Manu al, Rev. D 60–61 T otal number of u ser-addressable LBA sectors available (see Section 3.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFF h (268,435,455 sectors, 137 Gbytes).
Constellation Serial ATA Product Manual, Rev. D 31 Note. See the bit descriptio ns below for words 63 , 84, and 88 of the Identify Drive data. 108–1 1 1 The mandatory value of the world wide name (WWN) for the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indi ca ting 64-bit WWN support.
32 Constellation S erial ATA Pro duct Manu al, Rev. D Bit Wor d 8 8 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported.
Constellation Serial ATA Product Manual, Rev. D 33 5.3.2 Set Featu res comman d This command controls the implement ation of various fe at ures th at the drive suppo rts. When the drive receives this command, it sets BSY , checks the contents of the Features r e gister , clears BSY and generate s an inter- rupt.
34 Constellation S erial ATA Pro duct Manu al, Rev. D 5.3.3 S.M.A.R.T . commands S.M.A.R.T . provides near-term failure pre d iction for disc d rives. When S.M.A.R.T . is enabled , the drive moni- tors predetermined drive attributes that are suscep t ible to degradation over time.
Constellation Serial ATA Product Manual, Rev. D 35 Index A ACA 19 acceleration 16 acoustics 17 Agency certification 18 altitude 15 Ambient tempera ture 15 ambient temper ature 9 , 10 Annualized Failur.
36 Constellation S erial ATA Pro duct Manu al, Rev. D Information Technology Equipm ent (ITE) 18 Initialize Device Parameters 27 Input noise ripple 13 input voltage 10 interface 8 , 25 internal da ta-.
Constellation Serial ATA Product Manual, Rev. D 37 Security Erase Unit 28 Security Freeze 28 Security Set Password 28 Security Unlock 28 Seek 28 Seek time 9 Serial ATA (SATA) interface 25 serial ATA p.
38 Constellation S erial ATA Pro duct Manu al, Rev. D.
.
Seagate T echnology LLC 920 Disc Drive , Scotts V a lley , California 95066-4544, USA Publicat ion Number : 100538694, Re v . D.
An important point after buying a device Seagate ST9500530NS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate ST9500530NS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate ST9500530NS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate ST9500530NS you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate ST9500530NS will certainly help you make a decision on the purchase.
If you already are a holder of Seagate ST9500530NS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate ST9500530NS.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate ST9500530NS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate ST9500530NS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
