Instruction/ maintenance manual of the product ST9320328CS Seagate
Go to page of 46
Product Manual Pipeline HD Mini Series SATA 100560196 Rev. E December 2010 ST9500323CS ST9320328CS ST9250311CS ST91603110CS.
Revision history Copyright © 2010 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100560196, Rev. E December 2010 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Pipeline HD Mini Series SATA Product Manual, Rev. E i.
ii Pipeline HD Mini Series SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E iii Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface .
iv Pipeline HD Mini Series SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E v List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Attaching SATA cabling . . . . . . . . . .
.
Pipeline HD Mini SATA Product Manual, Rev. E vii For information regarding online support and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: • Presale.
viii Pipeline HD Mini SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Pipeline HD ® Mini Serie.
2 Pipeline HD Mini Series SATA Product Manual, Rev. E In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current sys- tem and expect all of your existing applications to work as normal.
Pipeline HD Mini Series SATA Product Manual, Rev. E 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the Pipeline HD Mini Series SATA models.
4 Pipeline HD Mini Series SATA Product Manual, Rev. E * One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.
Pipeline HD Mini Series SATA Product Manual, Rev. E 5 2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST9500323CS 500 Gbytes 976,773,168 512 ST9320328CS 320 Gbytes.
6 Pipeline HD Mini Series SATA Product Manual, Rev. E 2.4 Physical organization Drive model Read/write heads Number of discs ST9500323CS 4 2 ST9320328CS 3 ST9250311CS 2 1 ST91603110CS 2.
Pipeline HD Mini Series SATA Product Manual, Rev. E 7 Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted val- ues.
8 Pipeline HD Mini Series SATA Product Manual, Rev. E During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down model Table 3: DC power Power dissipation +5V input average (25° C) ST9500323CS and ST9320328CS ST9250311CS and ST91603110CS Spinup (max) 1 amp Seek 1.
Pipeline HD Mini Series SATA Product Manual, Rev. E 9 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz.
10 Pipeline HD Mini Series SATA Product Manual, Rev. E • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero.
Pipeline HD Mini Series SATA Product Manual, Rev. E 11 2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mount- ing screws.
12 Pipeline HD Mini Series SATA Product Manual, Rev. E *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase ac oustic and power to operational levels . Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs.
Pipeline HD Mini Series SATA Product Manual, Rev. E 13 2.13 Reliability Measurement type Specification Nonrecoverable read errors 1 per 10 14 bits read, max. Annualized Failure Rate (AFR) 0.55% (nominal power, 25°C ambient temperature) Also, refer to Section 2.
14 Pipeline HD Mini Series SATA Product Manual, Rev. E Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Arti- cle 11 of the Electromagne.
Pipeline HD Mini Series SATA Product Manual, Rev. E 15 2.15.1 European Union Restriction of Hazardous Substances (RoHS) The European Union Restriction of Hazardous Substances (RoHS) Directive, restric.
16 Pipeline HD Mini Series SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E 17 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive.
18 Pipeline HD Mini Series SATA Product Manual, Rev. E For installations which require cables, you can connect the drive as illustrated in Figure 2. Figure 2.
Pipeline HD Mini Series SATA Product Manual, Rev. E 19 Measurements shown in Figure 3 are in inches. Figure 3. Mounting dimensions—top, side and end view.
20 Pipeline HD Mini Series SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E 21 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA pro- grammed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.
22 Pipeline HD Mini Series SATA Product Manual, Rev. E Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12.
Pipeline HD Mini Series SATA Product Manual, Rev. E 23 Device Configuration Identify B1h/C2h Device Configuration Set B1h/C3h Download Microcode 92h Execute Device Diagnostics 90h Flush Cache E7h Flus.
24 Pipeline HD Mini Series SATA Product Manual, Rev. E S.M.A.R.T. Enable Operations B0h/D8h S.M.A.R.T. Enable/Disable Auto Offline B0h/DBh S.M.A.R.T. Enable One Attribute Modification B0h/E0h S.M.A.R.T. Execute Offline B0h/D4h S.M.A.R.T. Read Attribute Thresholds B0h/D1h S.
Pipeline HD Mini Series SATA Product Manual, Rev. E 25 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27.
26 Pipeline HD Mini Series SATA Product Manual, Rev. E 54 Number of current logical cylinders xxxx H 55 Number of current logical heads xxxx H 56 Number of current logical sectors per logical track xx.
Pipeline HD Mini Series SATA Product Manual, Rev. E 27 92 Master password revision code FFFE H 93 Hardware reset value (see description following this table) xxxx H 94 Auto acoustic management setting xxxx H 95–99 ATA-reserved 0000 H 100–103 Total number of user-addressable LBA sectors available (see Section 2.
28 Pipeline HD Mini Series SATA Product Manual, Rev. E 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt.
Pipeline HD Mini Series SATA Product Manual, Rev. E 29 Note. At power-on, or after a hardware or software reset, the default values of the features are as indicated above. 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives.
30 Pipeline HD Mini Series SATA Product Manual, Rev. E.
Pipeline HD Mini Series SATA Product Manual, Rev. E 31 Index A ACA 14 acoustics 4 , 11 Active mode 9 Address 23 AFR 13 Agency certification 13 Altitude 10 Altitude, nonoperating 4 Altitude, operating .
32 Pipeline HD Mini Series SATA Product Manual, Rev. E Guaranteed sectors 3 , 5 guaranteed sectors 5 H handling 17 Handling precautions 17 heads 5 Height 3 height 6 Humidity 10 humidity 4 I I/O data-t.
Pipeline HD Mini Series SATA Product Manual, Rev. E 33 Read Sectors without Retries 23 Read Stream DMA Extended 23 Read Stream Extended 23 Read Verify Sectors 23 Read Verify Sectors Extended 23 Read V.
34 Pipeline HD Mini Series SATA Product Manual, Rev. E.
.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100560196, Rev. E, Printed in USA.
An important point after buying a device Seagate ST9320328CS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate ST9320328CS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate ST9320328CS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate ST9320328CS you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate ST9320328CS will certainly help you make a decision on the purchase.
If you already are a holder of Seagate ST9320328CS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate ST9320328CS.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate ST9320328CS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate ST9320328CS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
