Instruction/ maintenance manual of the product ST610712DE Seagate
Go to page of 48
PRODUCT MANUAL ST1.3 Series Rev . C F ebruar y 2007 ST612712DEG ST612712DE ST610712DEG ST610712DE ST680712DEG ST680712DE ST660712DEG ST660712DE.
Revision st atus summary sheet Copyright © 2006 - 2007 Seagate T echn ology LLC. All rights reserved. Printe d in U.S.A. Publication number: 100409345, Rev . C February 2007 Seagate, Seagate T e chnology and th e W ave logo ar e registered tr ademarks of Seagate T echno logy LLC in the United S tates and/or other countries.
ST1.3 Series Product Manu al, Rev. C i Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Disclaimer . . . . . . . . . . . . . . . . . .
ii ST1.3 Series Product Manu al, Rev. C.
ST1.3 Series Product Manu al, Rev. C iii List of Figures Figure 1. ST1.3 Series IDE interface (ZIF connector) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. ST1.3 Series breather hole location . . . . . . . . . . .
iv ST1.3 Series Product Manu al, Rev. C.
ST1.3 Series Product Manu al, Rev. C 1 1.0 Introduction This manual describes the functiona l, mechanical and inte rface spec ifications for the following Seagate ® ST1.3 Series drives: • ST612712DE-12GB, ST61 0712DE-10GB, ST680712DE-8 GB and ST660712DE-6GB disc drives with a ZIF (zero inser tion force) con nector using an IDE interf ace.
2 ST1.3 Series Prod uct Manual, Re v. C 1.1 Disclaimer Seagate T echno logy LLC makes no warranties whatsoever , including any warranty of merc hantability , non- infringement, fitness for any p articular purpose, or a ny warranty otherwise arising out of any pr oposal, specifi - cation or sample.
ST1.3 Series Product Manu al, Rev. C 3 2.0 Drive specifications Unless otherwise noted, all specific ations are meas ured under a mbient conditions, at 25°C, and nominal power.
4 ST1.3 Series Prod uct Manual, Re v. C Read/write power (typical 3.3V) 230/240 mA Performance idle mode (typical 3.3V) 140 mA Low power idle mode (typical 3.
ST1.3 Series Product Manu al, Rev. C 5 2.2 Formatted cap acity 2.3 Default logical geometry LBA mode When addressing these d rives in LBA mode, all bloc ks (sectors) are co nsecutively numbered from 0 to n–1, where n is the number of guara nteed sectors as defined above .
6 ST1.3 Series Prod uct Manual, Re v. C 2.4 Recording and interface tec hnology 2.5 Physical characteristics 2.6 Time to rea dy T echnolo gy Specification Interface Seagate (ZIF) Flex Connector (35-wa.
ST1.3 Series Product Manu al, Rev. C 7 2.7 Power specifications The drive receive s DC power (+3.3V) thr ough the ZIF (IDE interface) connector for ST612712DE, ST612712DEG, ST 610712DE, ST610712DEG, ST68 0712DEG, ST680712DE, ST6607 12DEG and ST660712DE models.
8 ST1.3 Series Prod uct Manual, Re v. C * During period s of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase ac oustic and power to operational levels . 2.7.1.1 T ypical curren t profile Figure 4.
ST1.3 Series Product Manu al, Rev. C 9 2.7.2 Conducted noise Input noise ripp le is measured at the ho st system powe r supply across an equivalent 15- ohm resistive load on the +3.3 volt line. Using 3.3-volt power , the drive is expe ct ed to operate wit h a maximum of 7 0 mV peak-t o-peak squa re-wave injected nois e at up to 20 MHz.
10 ST1.3 Series Product Ma nual, Rev. C 2.7.4 Po wer-manage ment modes The drive provides pro grammable power manage ment to pr ovide greater ener gy effici en cy . The drive fe atures the following power-ma nagement modes: • Active mode The drive is in Active mode during the r ead/write and seek oper ations.
ST1.3 Series Product Manu al, Rev. C 11 2.8 Environment al specifications 2.8.1 Ambie nt temperat ure Ambient temperature is defined as th e temperature of the environmen t immediatel y surr ounding the drive. Actual drive cas e temperatur e should not exce ed 70°C (158°F) within the ope rating ambient conditions.
12 ST1.3 Series Product Ma nual, Rev. C 2.8.5 Shoc k All shock measurement s in this se ction are carried ou t at drive level. For all linear shock test, operating or non - operating, the input shock .
ST1.3 Series Product Manu al, Rev. C 13 2.8.6.1 Operating sweep sine vibration The following lists the maximum operat ing sweep sine vibration levels that the drive may experience while meeting the performan ce standards spe cified. It will c onsist of a forward and backward sweep from 10 Hz to 500 Hz to 10 Hz.
14 ST1.3 Series Product Ma nual, Rev. C 2.8.6.4 Nonoperating random vibration The test consi sts of 15 minutes of ra ndom vibration using the power spe ctral density (PSD) levels specified in the table below . The vibration test level is 3.01 Gs RMS. The drive will not incur any physical damage when subsequen tly put into op eration.
ST1.3 Series Product Manu al, Rev. C 15 2.9 Acoustics Drive acoustics are measured a s overall A-weighted ac o ustic sound power levels (no pure tones). Discrete tone penaltie s are added to the A-w eighted soun d po wer (L W) with the following fo rmula only when determin - ing compliance: L Wt(spec) == L W + 0.
16 ST1.3 Series Product Ma nual, Rev. C 2.1 1 Reliability Measurement type Specification Nonrecoverable read errors 1 per 10 14 bits read, max. Load/Unload (LUL) cycles (25°C) 300,000 software-contro.
ST1.3 Series Product Manu al, Rev. C 17 2.12 Agency certification 2.12.1 Safety certification The drives are re cognized in accordance with UL 60950-1, CAN/CSA-C22.
18 ST1.3 Series Product Ma nual, Rev. C 2.12.4 China Restriction of Hazardous Substa nces (RoHS) Directive This product has an Envir onmental Protection Use Pe riod (EPUP) of 20 years.
ST1.3 Series Product Manu al, Rev. C 19 If necessary , you should consult your dealer or an ex perienced radio/television techn ician for additiona l sug - gestions. Y ou may find helpful the following booklet prep ared by the F ederal Communications Commission: How to Identify and Resolve Radio-T elevision Interference Problems .
20 ST1.3 Series Product Ma nual, Rev. C.
ST1.3 Series Product Manu al, Rev. C 21 3.0 Configuring and mounting the drive This section contains the specif ications an d instructions for configuring and mounting th e drive.
22 ST1.3 Series Product Ma nual, Rev. C Figure 8. ST1.3 Series imprope r handling exampl e • Always rest the drives on a padded, antistatic su rface until you moun t it in the system. • Do not remove the factory-in stalled labels from the drive or cover th em with addition al labels.
ST1.3 Series Product Manu al, Rev. C 23 • Handle the drive only by its ed ges or frame or designate d finger grip region during moun ting (see Figure 4).
24 ST1.3 Series Product Ma nual, Rev. C 3.3 Mounting considerations • Use an ela stic mounting material to protect driv es so as to ensure that more shock can be absorbed.
ST1.3 Series Product Manu al, Rev. C 25 4.0 Interface description These drives use the industry-st andard A T A task file interf ace that support s 16-bit data transfer s. It supports A T A programme d input/output (PIO) modes 0–4; multiw ord DMA modes 0–2, and Ultra DMA modes 0–4.
26 ST1.3 Series Product Ma nual, Rev. C Note. For ST1.3 Series, drive is opera ting in master-mode only , and the DASP# (Drive Active/Slave Present) that is commonly us ed to drive LED light to indica te drive activity is not available .
ST1.3 Series Product Manu al, Rev. C 27 4.1.1 Supported A T A commands The following t able lists A T A-standard commands th at th e drive supports . For a detailed description of the A T A commands, refer to A T A version 7 specification, V olume 1. (www .
28 ST1.3 Series Product Ma nual, Rev. C 4.1.2 Id entify Dev ice command The Identify Device command (command code EC H ) transfers information about the drive to the host followin g power up. The dat a is organized a s a single 512-byte bl ock of data , whose contents ar e shown in the table on pag e 28 .
ST1.3 Series Product Manu al, Rev. C 29 59 Number of sectors transferred during a Read Multiple or Write Multiple command 0100 H 60–61 T otal number of user-addressable LBA sectors available (see Section 2.
30 ST1.3 Series Product Ma nual, Rev. C Note. See the bit descriptio ns below for words 63 and 88 of the Identify Drive data: Description (if bit is set to 1) Bit Wor d 6 3 0 Multiword DMA mode 0 is supported . 1 Multiword DMA mode 1 is supported . 2 Multiword DMA mode 2 is supported .
ST1.3 Series Product Manu al, Rev. C 31 4.1.3 S et Feature s command This command controls the implement ation of various feat ures that the drive supports. When the drive r eceives this command, it sets BSY , checks the contents of the Features r egister , clears BSY and generate s an inter - rupt.
32 ST1.3 Series Product Ma nual, Rev. C.
ST1.3 Series Product Manu al, Rev. C 33 5.0 Seagate T echnology support services Internet For information regarding Seag ate products and service s, visit www .sea g ate.com . W orldwide support is available 24 hours da ily by email for your questions.
34 ST1.3 Series Product Ma nual, Rev. C Customer Service Operations W arranty Service Seagate of fers worldwide custome r support for Seagate product s. Seagate d istributors, OEMs and other direct customers should contact their Seagate Customer Serv ice Operations (CSO) representative for wa rranty- related issues.
ST1.3 Series Product Manu al, Rev. C 35 Publication feedback survey We ar e interested in you r comments and su ggestions rega rding th is publication. Please take a few minu tes to participate in our survey at the follow ing URL: http://sur vey .sea g ate.
36 ST1.3 Series Product Ma nual, Rev. C.
ST1.3 Series Product Manu al, Rev. C 37 Index A acoustics 1 5 Active m ode 10 agency certification (regulatory) 17 altitude 11 ambient cond itions 3 ambient temperature 11 areal density 1 , 6 ATA-stan.
38 ST1.3 Series Product Ma nual, Rev. C Mounting c onsideration s 24 mounting the dr ive 21 , 2 2 N noise 9 nominal po wer 3 nonopera ting random v ibration 1 4 nonoperating sh ock 1 , 12 Nonoperating.
ST1.3 Series Product Manu al, Rev. C 39 Z zero insertion force 1 ZIF 1 ZIF conn w-FPC Tab Groove 24.
40 ST1.3 Series Product Ma nual, Rev. C.
.
Seagate T echnology LLC 920 Disc Drive, Scotts V alley, Calif ornia 95066-4544, USA Publication Number: 100409345 , Rev . C, Printed in U.S.A..
An important point after buying a device Seagate ST610712DE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate ST610712DE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate ST610712DE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate ST610712DE you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate ST610712DE will certainly help you make a decision on the purchase.
If you already are a holder of Seagate ST610712DE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate ST610712DE.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate ST610712DE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate ST610712DE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
