Instruction/ maintenance manual of the product ST2000VN000 Seagate
Go to page of 40
Product Manual Seagate ® NAS HDD 100724684 Rev. A April 2013 ST4000VN000 ST3000VN000 ST2000VN000.
© 2013 Seagate Technology LLC. All rights reserved. Publication number: 100724684, Rev. A April 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
NAS HDD Product Manual, Rev. A Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NAS HDD Product Manual, Rev. A.
NAS HDD Product Manual, Rev. A Figures Figure 1 Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 2 Mounting dimensions (2TB,3TB and 4TB) . . . . . . . . . . . . .
NAS HDD Product Manual, Rev. A.
NAS HDD Product Manual, Rev. A 7 For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technical- support/ Available services include: • Presales &.
8 NAS HDD Product Manual, Rev. A.
NAS HDD Product Manual, Rev. A 9 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® NAS HDD model drives: These drives provide .
10 NAS HDD Product Manual, Rev. A Introduction www.seagate.com The SATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.
NAS HDD Product Manual, Rev. A 11 2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: 2.
12 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com *All specifications above are based on native configurations. ** One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.
NAS HDD Product Manual, Rev. A 13 www.seagate.com Drive Specifications 2.2 Formatted capacity *One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity m ay vary depending on operating environment and formatting.
14 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com 2.4 Recording and interface technology 2.5 Physical characteristics Interface SATA Recording method TGMR Recording density 2TB an.
NAS HDD Product Manual, Rev. A 15 www.seagate.com Drive Specifications 2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature.
16 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down mode. * Idle1. During periods of drive idle, some offline activity may occur according to the S.
NAS HDD Product Manual, Rev. A 17 www.seagate.com Drive Specifications 2.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
18 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com 2.9.2 Ambient Temperature 2.9.3 Temperature gradient 2.9.4 Humidity 2.9.4.1 Relative humidity 2.9.4.2 Wet bulb temperature 2.9.5 Altitude 2.9.6 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws.
NAS HDD Product Manual, Rev. A 19 www.seagate.com Drive Specifications 2.9.6.3 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below.
20 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com 2.12 Reliability - Mean Time Between Failure The product will achieve a Mean Time Between Failure Rate (MTBF) of 1,000,000 hours when operated in an environment of ambient air temperatures of 25°C.
NAS HDD Product Manual, Rev. A 21 www.seagate.com Drive Specifications Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of th.
22 NAS HDD Product Manual, Rev. A Drive Specifications www.seagate.com 2.15.2 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years.
NAS HDD Product Manual, Rev. A 23 3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
24 NAS HDD Product Manual, Rev. A Configuring and Mounting the Drive www.seagate.com Figure 1 Attaching SATA cabling Each cable is keyed to ensure correct orientation.
NAS HDD Product Manual, Rev. A 25 4.0 SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.
NAS HDD Product Manual, Rev. A 26 Notes 1. All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12.
NAS HDD Product Manual, Rev. A 27 www.seagate.com SATA Interface Device Configuration Identify B1 H / C2 H Device Configuration Restore B1 H / C0 H Device Configuration Set B1 H / C3 H Device Reset 08.
28 NAS HDD Product Manual, Rev. A SATA Interface www.seagate.com Seek 70 H Set Features EF H Set Max Address F9 H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right.
NAS HDD Product Manual, Rev. A 29 www.seagate.com SATA Interface 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on page 26.
30 NAS HDD Product Manual, Rev. A SATA Interface www.seagate.com 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxx H 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB).
NAS HDD Product Manual, Rev. A 31 www.seagate.com SATA Interface 92 Master password revision code FFFE H 93 Hardware reset value xxxx H 94 Automatic acoustic management 8080 H 95–99 ATA-reserved 0000 H 100–103 Total number of user-addressable LBA sectors available (see Section 2.
32 NAS HDD Product Manual, Rev. A SATA Interface www.seagate.com 5 GPL feature set is supported. 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported. 7 WRITE DMA QUEUED FUA EXT command is supported. 8 64-bit World Wide Name is supported.
NAS HDD Product Manual, Rev. A 33 www.seagate.com SATA Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt.
34 NAS HDD Product Manual, Rev. A SATA Interface www.seagate.com 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time.
NAS HDD Product Manual, Rev. A 35 A ACA 21 acceleration 19 acoustics 19 Active 17 Active mode 17 Agency certification 20 altitude 18 Ambient temperature 17 ambient temperature 15 areal density 14 ATA .
36 NAS HDD Product Manual, Rev. A nominal power 15 Nonoperating shock 18 Nonoperating vibration 19 O operating 16 Operating power 15 Operating shock 18 Operating vibration 19 P Physical characteristic.
NAS HDD Product Manual, Rev. A 37 Voltage dips, interrupts 20 Voltage tolerance 16 W weight 14 wet bulb temperature 18 width 14 Write Buffer 28 Write DMA 28 Write DMA Extended 28 Write DMA FUA Extende.
.
.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte.
An important point after buying a device Seagate ST2000VN000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate ST2000VN000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate ST2000VN000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate ST2000VN000 you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate ST2000VN000 will certainly help you make a decision on the purchase.
If you already are a holder of Seagate ST2000VN000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate ST2000VN000.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate ST2000VN000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate ST2000VN000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
