Instruction/ maintenance manual of the product G-20 Scytek electronic
Go to page of 12
VEHICLE SECURITY SYSTEM G-20.
G-20 - Page 1 PLEASE NOTE: Some of the features described in this manual may require additional parts and/or labor, and may not be included as part of the standard installation of this unit. Additionally, many features of this security system have selectable options that must be activated or programmed during the system’s installation.
Remote Transmitter Description The G-20 Security S ystem is supplied with two 4-button Remote T r ansmitters used to control system operations. Button 1 Arms the system and when held for 2 seconds, activ ates the system’ s Panic f eature. Button 1 also locks the doors when the system is in V alet Mode.
G-20 - Page 3 Tamper Alert If the system was triggered while awa y , the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition.
Page 4 - G-20 Remote Arming The system monitors 3 independent areas ( zones ) while armed: doors, hood/trunk, and shock sensor input. T o Arm the S ystem: 1. T urn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock.
1. T urn off the ignition. 2. Open the door and exit the vehicle. · Once all doors are closed and the dome light is off , the LED will begin flashing rapidly . 3. After 30 seconds, · The siren will chirp. · The parking lights will flash. · The doors will lock.
10 seconds on the last press. · The system will disarm. If the code is entered incorrectly , turn off the ignition and begin again. T o set the Emergency Override Code: 1. T urn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that y ou have entered Progr amming.
G-20 - Page 7 Ignition Controlled Door Locks F or added safety , the Ignition Door Locking f eature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors after the ignition key is turned off .
Page 8 - G-20 G-20 - Page 8 Entering System Programming T o enter S ystem Programming: 1. T urn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that y ou have entered Progr amming.
G-20 - Page 9 Page 9 - G-20 1. Horn Chirps with Arm & Disarm. Selects one of three modes: Normal, Horn Chirps, and Horn Chirps w/W arn. Normal. When selected, the horn will honk only when the alarm is triggered.
Page 10 - G-20 D o o r L o c k D i a g r a m s R everse P olarity Adding Actuators P ositive Horn Honk S t a r t e r I n t e r r u p t Negative T rigger P ositive T rigger blue green.
© ScyT ek Electronics 2009 G-20 4-11-09 W i r i n g D i a g r a m Shock Sensor Green - Lock Out (-) 500mA Blue - Unlock Out (-) 500mA V alet Switch LED Orange - Ground when Armed Output (-) 500mA Blu.
An important point after buying a device Scytek electronic G-20 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Scytek electronic G-20 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Scytek electronic G-20 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Scytek electronic G-20 you will learn all the available features of the product, as well as information on its operation. The information that you get Scytek electronic G-20 will certainly help you make a decision on the purchase.
If you already are a holder of Scytek electronic G-20, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Scytek electronic G-20.
However, one of the most important roles played by the user manual is to help in solving problems with Scytek electronic G-20. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Scytek electronic G-20 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
