Instruction/ maintenance manual of the product Self Contained Cuber CU1526 Scotsman
Go to page of 18
Installation and User's Manual for Self Contained Cubers Models CU1526, CU2026 and CU3030.
Introduction The design of this cuber is the result of years of experience and testing. Standard features include a removable bin for service and an on-off switch at the front of the cabinet for easy operational control. Keep this manual for future reference.
Installation: Product Specifications Location Limitations: The product is designed to be installed indoors, in a controlled environment. Air cooled models discharge very warm air into the room. Water cooled models discharge warm water into the building’s drain.
Model Number Description Example: • CU2026SA-1A • C= cuber • U=under the counter type • 20= nominal ice capacity in 10s of pounds • 26= nominal width of cabinet • S= Cube size. S=small or half dice cube. M=medium or full dice cube • A=Condenser type.
Water The quality of the water supplied to the ice machine will have an impact on the time between cleanings and ultimately on the life of the product. Water can contain impurities either in suspension or in solution. Suspended solids can be filtered out.
CU1526 and CU2026 Cabinet Layout May 2008 Page 5 CU1526, CU2026, CU3030 User Manual 5.48 13.9 39.0 99.0 22.12 56.2 4.00 MINIMUM UTILITY CLEARANCE 10.2 6.00 15.2 22.25 56.5 29.65 75.3 27.5 69.9 4.86 12.3 26.62 67.6 30.04 76.3 15.55 39.5 2.60 6.6 4.85 12.
CU3030 Cabinet Layout May 2008 Page 6 CU1526, CU2026, CU3030 User Manual 5.30 13.5 39.0 99.0 25.95 65.9 4.69 11.9 30.0 76.2 30.62 77.8 4.00 MINIMUM UTILITY CLEARANCE 10.2 6.00 15.2 24.25 61.6 29.63 75.3 6.99 17.7 3.19 8.1 4.33 11 29.36 74.6 2.77 7 4.65 11.
Ice Storage Bin Removal The ice storage bin is removable to allow access to the refrigeration system for service. 1. Remove front louvers. Remove left then right. 2. If the machine is in an ice making mode, push and release the Manual Harvest button to release any ice that might be on the evaporator.
Plumbing Requirements Connect to cold, potable water. A hand actuated valve within site of the machine is required. Air cooled models have a single 3/8” male flare inlet water connection. Water cooled models have an additional 3/8” FPT condenser inlet water connection, and a 1/2" FPT condenser drain.
Electrical The machine is supplied with a power cord. 208-230 volt, 60 Hz cords have NEMA 6-20P plugs. This is a cord-connected unit, and must be on a separate power supply. Check the dataplate for the voltage, ampacity and maximum fuse size and per the dataplate use fuses or HACR circuit breakers.
Initial Start Up 1. Remove left front louver. Check machine for any packing or wires rubbing moving parts. Note location of control board at the left. 2. Switch the on off switch to On. 3. Switch on the electrical power to the machine. Observe that some of the control’s indicator lights glow and its display shows O .
Adjustments Bridge Thickness - For the Service Tech Only 1. Remove left louver, locate controller on and off switches. 2. Push and hold Off till the machine stops. 3. Remove curtain. 4. Use a hex wrench and rotate the bridge thickness adjustment screw in 1/8 turn increments CW to increase bridge thickness.
Use and Operation Once started, the ice machine will automatically make ice until the curtain is held open by the ice at the top of the pile. The typical ice level when the machine is off will be several inches below the door sill. When ice level drops from use or meltage, the ice machine will resume making ice.
Control Switches There is a front on and off switch, located in the top center of the louvers. Switching this switch Off will immediately stop the machine. Switching it back on will cause the machine to restart in a timed harvest cycle. When that cycle is complete, normal ice making will resume.
Cleaning, Sanitation and Maintenance This ice system requires three types of maintenance: • Remove the build up of mineral scale from the ice machine ’s water system and sensors. • Sanitize the ice machine ’s water system and the ice storage bin.
14. Locate ice thickness sensor. Squeeze mounting legs together to release sensor. Wash the metal surfaces of the sensor and the adjustment screw with ice machine scale remover solution. Also wash the water distributor and curtain with the ice machine cleaner solution.
What to do before calling for service Reasons the machine might shut itself off: • Lack of water. • Freeze cycle takes too long. • Harvest cycle takes too long. • High discharge temperature. • Controller self test failure. Check the following: 1.
SCOTSMAN ICE SYSTEMS 775 Corporate Woods Parkway, Vernon Hills, IL 60061 800-533-6006 www.scotsman-ice.com 17-3234-01.
An important point after buying a device Scotsman Self Contained Cuber CU1526 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Scotsman Self Contained Cuber CU1526 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Scotsman Self Contained Cuber CU1526 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Scotsman Self Contained Cuber CU1526 you will learn all the available features of the product, as well as information on its operation. The information that you get Scotsman Self Contained Cuber CU1526 will certainly help you make a decision on the purchase.
If you already are a holder of Scotsman Self Contained Cuber CU1526, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Scotsman Self Contained Cuber CU1526.
However, one of the most important roles played by the user manual is to help in solving problems with Scotsman Self Contained Cuber CU1526. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Scotsman Self Contained Cuber CU1526 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
