Instruction/ maintenance manual of the product 7000A Schumacher
Go to page of 16
Fully Automatic Microprocessor Controlled Battery Charger with Engine St arter plus Battery T ester and Alternator T ester CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. 0099000417/0204 OWNER’S MANUAL Schumacher Electric Corporation Mount Prospect, IL 60056 U.
2 PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE EACH USE. The Model 7000A, Fully Automatic Battery Charger/T ester and Engine S tarter , of fers features to accommodate the needs for home or light commercial use. This manual will explain how to use this battery charger safely and effectively .
3 IMPORT ANT SAFETY INSTRUCTIONS • WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.
4 Never place charger directly above battery being charged. The gases from the battery will corrode and damage the charger. Never touch the battery clamps together when the charger is on. You could cause a spark. Never operate charger if it has received a hard blow, been dropped, or otherwise damaged.
5 BEFORE USING YOUR BA TTER Y CHARGER It is important to understand the charger’s requirements. This section explains the charger ’s electrical requirement s and how to prepare a battery for charging. PLUGGING IT IN Y our charger requires a 120V AC receptacle installed according to all local codes and ordinances.
6 OPERA TING INSTRUCTIONS IMPORT ANT : Follow all safety instructions and precautions when charging your battery . Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. heavy, unpainted metal part of the chassis or engine block, away from the battery (see figure above).
7 1. Note the polarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or -). The positive post is usually larger than the negative post. 2. Attach at least a 24-inch-long, 6- gauge (AWG), insulated battery cable to NEGATIVE (NEG, N or -) battery post.
8 Digital LED Display Mode LEDs Charge Rate LEDs Battery Type LEDs Switch Buttons Status LEDs CHARGER CONTROL DISPLAY MODE SWITCH Use this switch to set the function of the digital LED to one of the following three. • BATTERY %: The digital LED displays an estimate of the percent of charge of the battery connected to the charger battery clamps.
9 CONTROL P ANEL GUIDE 7000A CONTROL PANEL GUIDE MODE OF OPERA TION C h a r g e d C h a r g i n g C h e c k B a t t e r y % V o l t a g e A l t e r n a t o r % 2 A 2 0 A 7 0 A S t a r t R e g u l a r D e e p - C y c l e A G M , G e l Digital Display Initia l pow er-up, battery not detected O O O 0.
10 USING THE BUIL T -IN BA TTER Y TESTER OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery’s relative charge based on the battery voltage and the Battery Council International scale.
11 This battery charger has a built-in alternator tester that displays either an accurate alternator voltage or an estimate of the alternator ’s relative output compared to normal alternators. The Alternator % values displayed should be taken as general reference, not precise diagnosis.
12 while waiting and will reset if the engine is not cranked within 5 minutes. (If the charger resets, it sets itself for a 2A charge and REGULAR battery.) While waiting for cranking, the digital display shows the battery voltage (it can’t be set to percent).
13 COMPLETION OF CHARGING: Charge completion is indicated by the CHARGED (green) LED; when lit, the charger has stopped charging and switched to the Maintain Mode of operation. MAINT AIN MODE : When the CHARGED (green) LED is lit, the charger has started Maintain Mode.
14 BA TTER Y PERCENT AND CHARGE TIME This charger adjusts the charging time in order to charge the battery com- pletely , efficiently and safely . The microprocessor automatically makes the necessary decisions. However , this section includes guidelines that can be used to estimate charging times.
15 TROUBLESHOOTING Performance problems often can be corrected by the user . Please read through this chart for a possible solution to common problems.
16 LIMITED W ARRANTY SCHUMACHER ELECTRIC CORPORA TION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT , ILLINOIS 60056-2179 MAKES THIS LIMITED W ARRANTY T O THE ORIGINAL PURCHASER A T RET AIL OF THIS PRODUCT .
An important point after buying a device Schumacher 7000A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Schumacher 7000A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Schumacher 7000A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Schumacher 7000A you will learn all the available features of the product, as well as information on its operation. The information that you get Schumacher 7000A will certainly help you make a decision on the purchase.
If you already are a holder of Schumacher 7000A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Schumacher 7000A.
However, one of the most important roles played by the user manual is to help in solving problems with Schumacher 7000A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Schumacher 7000A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
