Instruction/ maintenance manual of the product X 7G Naga V X7g-NagaV X7g-NagaV Sceptre
Go to page of 22
X7G-NagaV User ’ s Manual.
i FCC Compliance Statement This device complies with part 15 of t he FCC Rules. Operation is subject to the following two conditions: 1. This device may not caus e harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
ii The Federal Communications Commission warns that changes or modifications of the unit not expre ssly approved by the party responsible for compliance could void the user ’s authority to operate the equipment.
iii T ABLE OF C ONTENTS TABLE OF CO NTENTS .......................................................................................... III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Ad.
1 Rev.1 The LCD Monitor Your New LCD Monitor Your LCD Monitor has been desi gned to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA.
2 Rev.1 After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-T o-PC Analog signal cable 15pin • User ’s manual If you find that any item to be missing or appear to be damaged, contact your dealer immediately.
3 Rev.1 Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Pow er-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2. Monitor Stand 3.
4 Rev.1 B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Brightness Adjustment "hot key": Press this + button to allow you to adjust the brightness of the LCD Monitor directly Brightness 50 2.
5 Rev.1 Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 ° . 10 Figure 1-3: Tilting the Monitor 0 to 10.
6 Rev.1 Connecting AC Power and Video Ca ble Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal.
7 Rev.1 The Display Controls The LCD Monitor’s Control Panel Figure 2-1: The Control Pa nel 1. : Enable the OSD Menu button or / Move the cursor to the left ( w hen OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3.
8 Rev.1 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the Y button causes the screen below to appear. 2. Use the Y & Z key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value.
9 Rev.1 Monitro Adjustment Allow you to adjust the LCD monitor’s display settings. Press the Adjustment control button to display the submenu. Use the Function Select button to select one of the fol.
10 Rev.1 To exits the Monitor-Control submenu OSD-control The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. OSD-H-POSITION: To change the position of the OSD on a horizontal plane.
11 Rev.1 COLOR: To select the LCD monitor’s color display. The available options are cold, warm and User. Selecting the user option lets you make individual adjustments to the R, G and B items. COLOR R, G and B ADJUST: To make individual adjustments to the Red, Blue, Green (RGB) gain for the color temperat ure.
12 Rev.1 To indicate display mode ti mings and firmware version. EXIT: To exit the Misc-Control submenu. EXIT: Use the OSD Exit item to close the OSD menu.
13 Rev.1 Note: 1) No video When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of.
14 Rev.1 Appendix A TFT LCD Monitor Specifications LCD Panel 17" SXGA Control Functions Power Software Power switch with LED indicator (ON/OFF) Main Menu Submenu MONITOR- CONTROL Auto Adjustment,.
15 Rev.1 Scanning Frequency H/V, Hz 24-80K 50-75 P o w e r Management M e e t s VESA DPMS Power Consumption (ON/OFF, W) 35W/1W Max. Dimensions WxHxD 14.
16 Rev.1 Appendix B Supported Timing Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 NEC PC98 640x400 21.05 56.42 24.83 2 MAC 13" mode 640x480 30.24 66.67 35.00 3 MAC 16" mode 832x624 57.
17 Rev.1 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may init ially experience an unstable or unclear display when a new display mode or new VGA card is selected.
18 Rev.1 4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance. PROBLEM: The LCD displays “signal out of range” error message 1.
An important point after buying a device Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV you will learn all the available features of the product, as well as information on its operation. The information that you get Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV will certainly help you make a decision on the purchase.
If you already are a holder of Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV.
However, one of the most important roles played by the user manual is to help in solving problems with Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sceptre Sceptre X 7G Naga V X7g-NagaV X7g-NagaV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
