Instruction/ maintenance manual of the product SE-3.5BS Scag Power Equipment
Go to page of 16
MODEL SE-3.5BS OPERATORS MANUAL OPERATORS MANUAL OPERATORS MANUAL OPERATORS MANUAL OPERATORS MANUAL THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG EDGER. READING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCE- DURES TO KEEP YOUR EDGER PERFORM- ING TO MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJUR Y . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine before cleaning.
SUBJECT P A GE Introduction .............................................................................................................. 1 Safety and Operating Instructions ........................................................................... 1-3 Setup & Operation .
1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this edger. Read it carefully and keep it for future reference.
2 SAFETY AND OPERA TING INSTRUCTIONS (CONT'D) n n n n n Dress Properly, cont. 3. Sturdy gloves and safety footwear are recommended. n n n n n Check The Edger Before Use 1. Never operate the edger unless guards and other protective devices are in place.
3 P R O P E R L Y P R O P E R L Y P R O P E R L Y P R O P E R L Y P R O P E R L Y S E R V I C E S E R V I C E S E R V I C E S E R V I C E S E R V I C E E N G I N E E N G I N E E N G I N E E N G I N E E N G I N E W I T H W I T H W I T H W I T H W I T H O I L O I L O I L O I L O I L A N D A N D A N D A N D A N D F U E L .
4 SAFETY AND OPERA TING INSTRUCTIONS (CONT'D) n n n n n Protect Operators 1. Keep a safe distance between two or more operators when working with a cutting crew at the same site.
5 SETUP & OPPERA TION (CONT'D) n n n n n Operating Instructions Figure 5 is a general view of the edger. Note: The right or left side of the edger refers to the view from the normal operating position, behind the handles. n n n n n Before Operation 1.
6 4. Remove the oil drain plug and drain the oil into an appropriate container. 5. After the oil is drained, replace the drain plug and refill the crankcase to the level specified in the engine owner's manual. 6. Replace the oil cap. 7. Dispose of the used oil properly.
7 MAINTENANCE (CONT'D) n n n n n Belt Tension Always adjust the belt tension after changing the belt. New belts may stretch. Excess tension on the belt will make holding the clutch difficult and cause the belts to wear. To adjust belt tension (See Figure 9): 1.
8 MAINTENANCE (CONT'D) n n n n n Rubber Debris Deflector Replace the rubber deflector when worn or damaged to prevent operator injury. n n n n n Lubrication Grease the edger periodically at the points shown on Figure 11. Use lithium-based grease.
9 TROUBLESHOOTING GUIDE Problem Cause Engine fails to start Fuel level is low. Spark plug lead wire disconnected. Throttle or choke not in starting position. Spark plug defective. Carburetor improperly adjusted. Old/stale gasoline. Engine kill switch in off position.
10 LAWN EDGER SE-3.5BS 390S0184 40 39 35 42 56 55 45 46 4 59 60 57 27 47 17 12 4 18 43 41 36 44 48 50 13(REF.) 50(REF.) 49 39 38 4 22 26 34 28 29 30 36 30 1 5 32 23 9 20 18 21 3 10 11 8 6 15 A A 7 37 13 16 36 46 24 24 44 36 25 62 61 46 33 52 49 58 59 45 54 3 49 31 53 63 9 43 18 12 3 37 4 20(REF.
11 1 481886 Engine, 3.5 HP. Briggs & Stratton 2 04001-12 Bolt, Hex Head 5/16-18 x 1.75" 3 04030-03 Lockwasher, 5/16" Spring 4 04021-10 Locknut, 5/16-18 Hex Elastic Stop 5 04063-05 Key, 3/16 x 3/16 x 1.50" 6 48451 Pulley, 2.50 Dia. - .
LIMITED LIMITED LIMITED LIMITED LIMITED W W W W W ARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL A CCESSOR CCESSOR CCESSOR CCESSOR CCESSOR .
P ART NO. 03070 PRINTED 12/98 PRINTED IN USA © 1998 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC.
An important point after buying a device Scag Power Equipment SE-3.5BS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Scag Power Equipment SE-3.5BS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Scag Power Equipment SE-3.5BS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Scag Power Equipment SE-3.5BS you will learn all the available features of the product, as well as information on its operation. The information that you get Scag Power Equipment SE-3.5BS will certainly help you make a decision on the purchase.
If you already are a holder of Scag Power Equipment SE-3.5BS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Scag Power Equipment SE-3.5BS.
However, one of the most important roles played by the user manual is to help in solving problems with Scag Power Equipment SE-3.5BS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Scag Power Equipment SE-3.5BS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
