Instruction/ maintenance manual of the product GC-STT Scag Power Equipment
Go to page of 29
MODEL GC-STT THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJUR Y . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 3.1 ASSEMBLY INSTRUCTIONS FOR 52" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
3 DISCHARGE CHUTE OPENING FRONT OF CUTTER DECK REAR OF CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-52"GC-STT install art CUTTER DECK BELL CRANK LIFT LINK SPACER SPACER NUT NUT WASHER BOLT, 3/8-16 x 1-1/2" BOLT, 3/8-16 x 1-1/4" P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L .
4 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the hardware at this time.
5 19 . Install the hose from the blower assembly to the hopper hood. Secure using the 8-1/2" clamps. WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install.
6 4.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
7 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . FIGURE 4-3 FIGURE 4-4 DISCHARGE CHUTE OPENING FRONT OF CUTTER DECK REAR OF CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-61"GC-STT install art RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
8 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 4-3, Page 7. Do not fully tighten the hardware at this time.
9 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 FIGURE 4-6 21 . Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard.
10 3. When installing this grass catcher on a machine with a serial number below 8619999, you will need to remove the discharge baffle from the bottom of the cutter deck. See Figure 5-2. Replace the discharge baffle with the new baffle provided with this grass catcher.
11 BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
12 13 . Install the hopper mounting brackets (p/n 451512 & p/n 451595) to the outside of the frame on the rear of the machine using 3/8-16 x 1" hex head bolts (p/n 04001-19) and 3/8-16 elastic stop nuts (p/n 04021-09). See Figure 5-6, Page 13.
13 FIGURE 5-6 1 1 2 3 3 3 3 3 4 4 4 4 5 5 4 4 Item # P ar t # Description 1 04001-46 Bolt, He x Head 3/8-16 x 2-1/4" 2 04001-19 Bolt, He x Head 3/8-16 x 1" 3 04021-09 Nut, Elastic Stop 3/8-16 4 04030-04 Lockw asher , 3/8 Spr ing 5 04041-07 Flatwasher , 3/8-.
14 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the bag assemblies from the grass catcher. 3. Remove the rubber strap holding the adapter to the blower assembly. See Figure 6-1. 4. Remove the belt from the spindle pulley.
15 NOTES.
16 GC-STT BLO WER HOUSING ASSEMBL Y W A R N IN G INSTALL BEL T COVER BEFORE OPERATING M ACHINE R E A D O P E R A T O R ' S M A N U A L 390STT0200A 1 2 3 3 45 47 45 4 5 6 7 8 9 9 10 10 11 11 12 12.
17 GC-STT BLO WER HOUSING ASSEMBL Y Ref. P a r t No . Number Description 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr .
18 GC-STT BLO WER MOUNTING COMPONENTS 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 19 20 21 16 17 18 390STT0203 RIGHT SIDE OF 61" CUTTER DECK SHOWN Note: Parts for 52"cutter deck may vary slightly from illustration. Some parts not shown for viewing purposes.
19 GC-STT BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482406 Belt Cov er , GC-STT - 52" 482378 B e lt C ov e r , GC-STT - 61" & 72" 2 04029-04 Wingnut, Plastic 3/8 Small 3 482300 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461419 Adapter , Blow er GC-STT 6 04040-14 Flatwasher , 1/4-.
20 GC-STT BUCKET SUPPORT COMPONENTS 1 2 3 4 4 6 8 5 5 9 9 9 9 5 11 5 16 16 16 16 16 16 18 18 13 13 19 20 14 21 21 22 23 23 24 31 11 5 32 33 33 26 27 28 29 30 32 3 41 42 40 49 9 48 47 46 13 45 4 25 4 5.
21 GC-STT BUCKET SUPPORT COMPONENTS R e f . Part No . Number Description 1 423302 Screen, Catcher Hood 2 04090-02 P op Riv et, 3/16 x .652 3 04041-19 Flatwasher , 3/16-.196 x .469 x .048 4 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4" 5 04041-07 Flatwasher , 3/8-.
22 1 2 3 4 5 6 7 8 9 10 11 12 13 390STT0201 GC-STT B A G SUPPORT BRA CKET AND SEAL.
23 GC-STT B A G SUPPORT BRA CKET AND SEAL Ref. Part No. Number Description -NOTE- Some of the hardware is common hardware and you may purchase it locally.
24 GC-STT DECALS 481039 482275 481327 482293.
25 NOTES.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03138 PRINTED 8-2003 PRINTED IN USA © 2003 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC WWW .SCAG .COM.
An important point after buying a device Scag Power Equipment GC-STT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Scag Power Equipment GC-STT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Scag Power Equipment GC-STT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Scag Power Equipment GC-STT you will learn all the available features of the product, as well as information on its operation. The information that you get Scag Power Equipment GC-STT will certainly help you make a decision on the purchase.
If you already are a holder of Scag Power Equipment GC-STT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Scag Power Equipment GC-STT.
However, one of the most important roles played by the user manual is to help in solving problems with Scag Power Equipment GC-STT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Scag Power Equipment GC-STT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
