Instruction/ maintenance manual of the product VPC-X360 Sanyo
Go to page of 29
SER VICE MANUAL Color Digital Camera VPC-X360E VPC-X360EX (Product Code : 126 251 01) (U.K.) (Product Code : 126 251 02) (Europe) (P AL General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2 2. DISASSEMBLY .........................
− 2 − Pin 1 2 8 34 2 H V Pin 9 Fig. 1-1.Optical Black Location (T op View) Pin No. 1 Symbol 2 3 4 5, 6, 7, 10 8 9 12 13 14 15 16 V φ 3 V φ 1 GND OS OD O SUB P L φ RS φ H1 φ H2 Pin Description.
− 3 − 1A 1 1Y 2 2A 3 2Y 4 3A 5 3Y 6 GND 7 4Y 8 4A 9 5Y 10 5A 11 6Y 12 6A 13 V CC 14 Fig. 1-2. IC902 Block Diagram 1 18 10 9 8 7 6 5 4 3 2 14 15 16 17 20 19 11 12 13 CPP1 CPP2 DC OUT VSHT V φ 1 V L V φ 2 V φ 4 V M V φ 3 XV4 CPP3 VH DCIN XSHT XV2 XV1 XSG1 XV3 XSG2 + - Change Pump Fig.
− 4 − Fig. 1-5. Horizontal T ransfer of CCD Imager and Extraction of Signal V oltage Fig. 1-6. Theory of Signal Extraction Operation H1 H2 H1 H2 H1 HOG RG CCD OUT PD Floating diffusion (1) H1 H2 H1 H2 H1 HOG RG CCD OUT PD (2) H1 H2 H1 H2 H1 HOG RG CCD OUT (3) H1 H2 RG CCD OUT 3.
−5− 1-2. CA2 CIRCUIT DESCRIPTION 1. Circuit Description 1-1. Scannning converter (Interlace converter) This circuit uses the function of a 64-Mbit SDRAMs to con- vert the non-interlaced signal which is output from the CCD into an interlaced signal for the video monitor .
−6− 3. LCD Block During EE, gamma conversion is carried out for the 10-bit RGB data which is input from the A/D conversion block of the CCD to the ASIC in order that the γ revised can be displayed on the video. The YUV of 640 x 480 is then transferred to the SVRAM.
−7− 1-3. PW1 POWER CIRCUIT DESCRIPTION 1. Outline This is the main power circuit, and is comprised of the follow- ing blocks. Switching controller (IC501) Digital and analog system and LCD 5.0 V system power out- put (L5010, Q5002, D5013, C5061) Digital 3.
−8− 1-4. PW1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit When UNREG power is supplied to the charge circuit and the CHG signal becomes High (3.3 V), the charging circuit starts operating and the main electorolytic capacitor is charged with high-voltage direct current.
−9− Pin Signal 1 3~7 8 9 10 11 13 14~19 20 21 22 31 32~69 70 71 73 74 75 76 77 78 79 80 81 82 84 86 87 88~90 83 85 91~93 CHG VOL SCAN IN 0~4 A VREF STBY (R) LED STBY (G) LED VSS NOT USED A VREF ON NOT USED CHG ON NOT USED VSS NOT USED P (A) ON P ON DIN CONNECT NOT USED A V JACK SO SCK IC XOUT XIN VDD XCIN XCOUT RESET BA T OFF RXD S.
−1 0− 0 1 2 0 1 23 SCAN OUT SCAN IN SHUTTER 1st BARRIER SHUTTER 2nd CARD LID CAMERA MODE PLA Y SET T able 4-2. Key Operation 2. Internal Communication Bus The SY1 circuit board carries out overall control of camera operation by detecting the input from the keyboard and the conditio n of the camera circuits.
−1 1− ASIC, memory RS232C driver CCD 8bit CPU MODE LCD LCD MONITOR Power voltage Lens cover close Playback Power switch ON- Auto power down Shutter switch ON Resolution, Flash, Self timer switch ON LCD finder 3.3 V 3.3 V 5 V (A), -7.5 V , +15 V etc.
−1 2− 2. DISASSEMBL Y 2-1. REMOV AL OF CABINET ASSEMBL Y (FRONT) AND CABINET ASSEMBL Y (BACK) 2-2. REMOV AL OF SY1 BOARD, TB2 BOARD AND TB1 BOARD 1. Two screws 1.7 x 4 2. Front cabinet 4. Cover battery 3. Back cabinet 1. Four screws 1.7 x 4 5. Cover jack 6.
−1 3− 2-3. REMOV AL OF LENS VF AND PW1 BOARD 1. Two screws 1.7 x 3 2. Lens VF 3. Two screws 1.7 x 3 4. Connector 5. Connector 6. Three screws 1.7 x 3 7.
−1 4− 2-4. REMOV AL OF LCD, CA2 BOARD AND CA1 BOARD 2-5. BOARD LOCA TION SY1 board TB2 board TB1 board PW1 board CA1 board CA2 board 1. FPC 2. LCD 3. Four screws 1.7 x 3 4. Connector 5. Screw 1.7 x 3 6. Two connectors 7. Two screws 1.7 x 3 8. Holder chassis CA2 9.
−1 5− 3. ELECTRICAL ADJUSTMENT 3-1. T able for Servicing T ools Note : J-1 color viewer is 100 - 1 10 V AC only . J-2 Siemens star chart is the same as before models. 3-2. Equipment 1. Oscilloscope 2. Digital voltmeter 3. AC adaptor 4. IBM R -compatible PC 5.
−1 6− 3-5. Connecting the camera to the computer 1. T urn of f both camera and computer . 2. Locate the port cover on the side of the camera. Press on the arrows and slide the cover down to open it. 3. Line up the arrow on the cable connector with the notch on the camera's serial port.
−1 7− 3-6. Adjust Specifications [PW1 board (Side A/B)] Note: 1. V oltage adjustment is necessary to repair in the PW1 board and replace the parts. 2. Power voltage set about +3.0 V . Preparation: 1. Connect CN103 on the CA2 board and CN502 on the PW1 board with extension cord.
−1 8− 8. A WB Adjustment Preparation: POWER switch: ON Adjusting method: 1. Set the all white pattern so that it becomes a full picture. (Do not enter any light.) 2. Double-click on the DscCalV123b. 3. Click the AWB, and click the Y es. 4. AWB adjustment value will appear on the screen.
−1 9− CL424 waveform CL426 waveform VG VG ± 0.2 V 10-2. LCD RGB Offset Adjustment Adjusting method: 1. Adjust LCD “ RGB offset ” so that the amplitude of the CL424 waveform is 7.5 Vp-p ± 0.3 V . 10-3. LCD Gain Adjustment Adjusting method: 1.
−2 0− 4. TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE BARRIER SW BARRIER SW ON NORMAL IC301-4, 93 CHECK S6002, CN302, D3069, R3021 IC302-7 (UP UNREG) CHECK IC132, PW1 IC301-81 (VDD) IC301-84 (RESET.
21 5 . PARTS LIST LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION N.S.P.: Not available as service parts. CABINET & CHASSIS PARTS 1 1 636 056 2479 ASSY,COVER LENS-SR662/E 2 636 055 5.
22 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION N.S.P.: Not available as service parts. CABINET & CHASSIS PARTS 2 1 645 029 2170 LENS(ASSY) 2 645 032 5854 OPTICAL FILTER 3 636 052.
23 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION Note: 1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-PO.
24 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C9022 403 312 6805 CERAMIC 0.1U Z 16V C9023 403 320 5302 CERAMIC 0.15U K 25V C9025 403 312 6805 CERAMIC 0.1U Z 16V C9026 403 312 6805 CERAMIC 0.1U Z 16V C9029 403 312 6805 CERAMIC 0.1U Z 16V C9030 403 296 8000 TA-SOLID 22U M 10V C9031 403 311 3409 CERAMIC 0.
25 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION X1101 645 024 0461 OSC,CRYSTAL 17.734476MHZ, EXCEPT VPC-X360 (INDUCTORS) L1101 645 016 0363 INDUCTOR,600 OHM L1103 645 038 2161 INDUCTO.
26 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION (SWITCH) S1001 645 023 0844 SWITCH,PUSH 1P-1TX1, (CONNECTORS) CN101 645 036 7489 SOCKET,PWB-PWB 40(N.S.P) CN102 645 030 6655 SOCKET,PWB-PWB 50(N.S.P) CN103 645 035 5387 PLUG,PWB-PWB 30P (N.
27 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C5058 403 345 3109 POS-SOLID 33U M 10V C5059 403 345 3000 POS-SOLID 47U M 6.3V C5061 403 335 1405 CERAMIC 10U K 6.3V C5062 403 345 3000 POS-SOLID 47U M 6.3V C5064 403 345 3901 CERAMIC 3.
28 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION D3041 407 199 1809 LED SML-020MLT, VF LED D3042 407 187 6304 LED SML-110VT, SELF TIMER LED D3051 407 149 0807 DIODE 1SS355 D3052 407 16.
OVERALL WIRING.
An important point after buying a device Sanyo VPC-X360 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo VPC-X360 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo VPC-X360 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo VPC-X360 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo VPC-X360 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo VPC-X360, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo VPC-X360.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo VPC-X360. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo VPC-X360 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
