Instruction/ maintenance manual of the product STW-2 Sanyo
Go to page of 12
OWNER’S MANUAL W 851641 19653000 © SANYO 2001 SANYO Electric Co., Ltd. Osaka, Japan P ACKAGED TERMINAL AIR CONDITIONER Cool / Heat Model STW -2 Series Operating Instructions Installation Instructions Contents Page Alert Symbols ....................
2 Installation Location • We recommend that this air conditioner be installed properly by qualified installation technicians in accor- dance with the Installation Instructions provided with the unit. • Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown on the nameplate.
3 Operation: 1. Set the mode selector for fan, cooling or heating opera- tion. 2. Set the thermostat to the desired position. (Refer to the Setting T emperature Guide on page 2.) The temperatures at the Setting T emperature Guide on Page 2 are provided for reference only , and may differ from the actual temperature of the room.
4 Fan Cycle Switch The Fan Cycle Switch is located under the control panel behind the front grille. This switch is set to CONT at the factory to provide continuous fan operation in cool or heat modes. Leaving the switch at the CONT setting allows continuous circulation of room air and will keep the room temperature at stable condition.
5 Control Panel The control panel is shipped with a protective plastic film. This film can be left on or removed. T o clean, use a damp cloth and mild detergent. Outdoor Coil The coil on the outdoor side of the unit should be checked periodically and cleaned if clogged with dirt or soot from the atmosphere.
IMPORT ANT! Please Read Before Starting This air conditioner meets strict safety and operating stan- dards. As the installer or service person, it is an important part of your job to install or service the system so it oper- ates safely and efficiently .
7 1. NAMES OF P AR TS Rear grille/louver** W all case** Chassis Front grille* * Shipped with the chassis ** Check essential components list on chassis 2. W ALL CASE AND REAR GRILLE 1) The STK01WC wall case must be properly installed according to the instructions packed with the case.
8 4. PERMANENT CONNECTION 4-1. For 230/208V Units The 230/208V model is equipped for connection with a power cord according to the unit capacity at the time of shipment. Should local codes or special requirements speci- fy permanent connection of this unit, use optional adapter kit (Cover plate and Bottom plate) STK02JB.
3) Attach the field-supplied conduit to the bottom plate. 4) Connect the power supply conductors to the T erminal block and the Grounding screw . 5) Attach the cover plate. 6) Reinstall the front grille. (See “Front Grille” on page 3.) 9 6. TEMPERA TURE LIMITING The normal range of the thermostat control is approximately 55°F to 88°F .
10 Remote Control Class 2 Remote FDC Low v oltage T er minals on Interf ace kit 7 . REMOTE CONTROL The unit may be controlled either by the unit-mount- ed controls (Control Panel) or by optional Class 2 ther- mo controller (SC2001 for Cool/Heat Model and SC2201 for Heat Pump Model) with optional Interface kit (STK02L VC).
11 Product Information If you have problems or questions concerning your Air Conditioner , you will need the following information. Model and serial numbers are on the nameplate of the cabinet.
SANYO FISHER COMP ANY A DIVISION OF SANYO NORTH AMERICA CORPORA TION 21605 plummer Street, Chatsworth, CA 9131 1 U.S.A. In Canada SANYO Canada Inc. 300 Applewood Crescent, Concord, Ontario, L4K 5C7, C.
An important point after buying a device Sanyo STW-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo STW-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo STW-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo STW-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo STW-2 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo STW-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo STW-2.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo STW-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo STW-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
