Instruction/ maintenance manual of the product SHA-KC64UG Sanyo
Go to page of 64
Save These Instructions! 1. RCS-SH80UG ( Wired type: f or all indoor units ) 2. RCS-SH80U A.WL ( Wireless type: f or X and T type indoor units ) RCS-BH80U A.WL ( Wireless type: f or K and U type indoor units ) 3. TM-SH80UG ( W eekl y Timer ) 4. SHA-KC64UG ( System Remote Contr oller ) Pub .
0 SANYO Control Unit Cover 5/2/01 1:40 PM Page 2.
Save These Instructions! RCS-SH80UG Split System Air Conditioner • INSTR UCTION MANU AL SEMI-CONCEALED CEILING-MOUNTED W ALL-MOUNTED CONCEALED DUCT (4-W A Y) XH1242 KH1242 UH1242 XH1842 KH1842 UH184.
Contents P age Product Inf ormation .......................................................................................... 2 Aler t Symbols ................................................................................................... 2 Installation Location .
Installation Location • W e recommend that this air conditioner be installed pr operly b y qualified installation technicians in accor dance with the Installation Instructions pro vided with the unit.
Air outlet Celling panel (optional) OI-432-01 - 4EG 1 - 4 Names of P ar ts INDOOR UNIT SEMI-CONCEALED X type (4-W A Y) Air outlet Air intake W ALL-MOUNTED K type Air intake Air outlet CEILING-MOUNTED .
O: VENTILA TION button G: CHECK button OI-432-01 - 5EG 1 - 5 Remote Cotrol Unit • With this remote controller , you can operate indoor units up to 8 units. • Once you set y our operation conditions, you can operate the units only b y pressing the ON/OFF operation button.
OI-432-01 - 6EG 1 - 6 F: FIL TER reset button Use this button to reset the filter sign . The air conditioner has a timer f or the filter and informs you when the filter needs cleaning. G: CHECK button This button is used only when servicing the air conditioner .
OI-432-01 - 7EG 1 - 7 1) When two remote control units are being used in one group control* system, a) the most recent b utton that is pressed on any remote control unit is eff ective. b) either a main-remote control unit or a sub-remote control can set the timer .
OI-432-01 - 8EG 1 - 8 A: When the unit is in the heating standby mode , the indicator appears. (Refer to the description of the Special Remarks on page 12.
OI-432-01 - 9EG 1 - 9 T o warm up the system, the power mains m ust be tur ned on at least five (5) hours bef ore operation. STEP 1 T o start the air conditioner Press the operation b utton (ON/OFF button). STEP 2 Setting the mode Press the MODE button to select the mode of y our choice.
Adjusting the Airflo w Direction ■ Semi-concealed type 4-way type (X) This air conditioner is equipped with auto flaps. Y ou can set the airflo w direction to a specific angle or to the sweep mode using the remote control unit. (Refer to the description of the remote control unit.
Adjusting the Airflow Direction (contin ued) ■ W all mounted type (K) A. V ertical directions (automatic) Confirm that the remote control unit has been tur ned on. Press the FLAP button to start the flap moving up and down. If you want to stop the flap mov ement and to direct the air in the desired direction, press the FLAP button again.
Special Remar ks • Once the room temperature reaches the le vel that was set, the unit repeats the cycle of turning on and off automatically . • In order to pre vent the humidity in the room from rising again, the indoor f an also tur ns off when the unit stops operating.
Setting the Timer Use this mode to turn off the appliance automatically after the length of time set. Use this mode to turn the appliance off automatically after the same set time e ver y time. Use this mode to star t the appliance automatically after the length of time set.
How to set the OFF timer ( ) (Example) T o stop the air conditioner after 3.5 hours Operation Indication 1. Press the ON/OFF b utton to star t the air conditioner . 2. Press the TIMER SET b utton once to select the mode. 3. Press the b utton until 3.5 is displa yed.
Care and Cleaning 1. For safety , be sure to turn the air conditioner off and also to disconnect the power bef ore cleaning. 2. Do not pour water on the indoor unit to c lean it. This will damage the internal components and cause an electric shock hazar d.
Care and Cleaning (continued) 4. Remov e the air filter attached to the air intake grille. 1. Remov e the bolt screws on the finger-hold using a scre w driver . (After cleaning, be sure to attach the two bolt scre ws.) 2. T ake hold of the finger-hold on the air intak e grille and slide it to the rear , and the grille will open downward.
T roub leshooting If your air conditioner does not w or k properly , first check the f ollowing points before requesting service. If it still does not work properly , contact your dealer or a service center . OI-432-01 - 17EG 1 - 17 Tips f or Energy Sa ving A void • Do not bloc k the air intake and outlet of the unit.
1 1 RCS-SH80U 5/2/01 1:38 PM Page 18.
Sa ve These Instructions! RCS-SH80U A.WL RCS-BH80U A.WL • INSTR UCTION MANU AL Wireless Remote Controller f or Split System F or information on installing the wireless remote controller , refer to the INST ALLA TION INSTR UCTIONS accompanying the outdoor unit.
Contents P age Product Inf or mation .......................................................................................... 2 Aler t Symbols ................................................................................................... 2 Installation Location .
Installation Location • W e recommend that this air conditioner be installed properly b y qualified installation technicians in accor dance with the Installation Instructions pro vided with the unit. • Bef ore installation, check that the voltage of the electric supply in your home or office is the same as the v oltage shown on the nameplate.
Unit Displa y and Operation Controller f or X and T T ypes OPERA TION lamp This lamp lights when the appliance is turned on. TIMER lamp This lamp lights when the system is being controlled b y the timer . ST ANDBY lamp When the unit is in the heating standby condition, the ST ANDBY lamp lights.
OI-404-02 - 5EG 2 - 5 Unit Display and Operation Contr oller for X and T T ypes (continued) SER VICING switches ON/OFF operation button This button is f or tur ning the air conditioner on and off (automatically setting cooling or heating operation). SWEEP button Use this b utton to make the airflow direction s weep up and down automatically .
OI-404-02 - 6EG 2 - 6 Operation Controller with Receiv er (Separated from Indoor Unit) f or K and U T ypes A: Operation controller Y ou can operate this air conditioner using the (separated from indoor unit) operation controller without the wireless remote controller .
Using the Wireless Remote Controller 1. Press and slide the lid on the back of the wireless remote controller in the direction of the arrow . 2. Install two AAA alkaline batteries (LR03). Make sure the batteries point in the direction marked in the battery compar tment.
OI-404-02 - 8EG 2 - 8 Using the Wireless Remote Controller (contin ued) When using the wireless remote controller , alwa ys point the unit’ s transmitter head directly at the air conditioner’ s receiver . The wireless remote controller can be operated from either a non-fix ed posi- tion or a wall-mounted position.
OI-404-02 - 9EG 2 - 9 Remote Cotrol Unit A: ON/OFF operation button This button is f or tur ning the air conditioner on and off . B: MODE button Use this button to select one of the f ollowing fiv e operations: (A UT O) : Used to automatically set cooling or heating operation.
F: FLAP button ( ) 1. Use this button to set the airflo w direction to a specific angle. The airflow direction ( ) is display ed on the remote control unit. • In the cool mode and dry mode, when the flaps are set in a downwar d position, condensation ma y form and drip around the vent.
OI-404-02 - 11EG 2 - 11 O: SENSOR button Use this button to s witch to the temperature sensor of the remote controller . The temperature sensor of the air-conditioner is selected at the f actor y and the displa y indicates under this selection.
Description A: When you press the SENSOR b utton, the (SENSOR) indicator appears or disappears. B: The currently selected operation mode is displa yed. C: When setting the timer , the selected timer mode is displa yed. D: The currently selected F AN SPEED , FLAP ANGLE and SWEEP status are displa yed.
Operation OI-404-02 - 13EG 2 - 13 T o warm up the system, the power mains m ust be tur ned on at least five (5) hours bef ore operation. STEP 1 T o start the air conditioner Press the operation b utton (ON/OFF button). STEP 2 Setting the mode Press the MODE button to select the mode of y our choice.
Operation without the Wireless Remote Controller If you ha ve lost the wireless remote controller or if it is not working properly , follow the steps belo w: STEP 1 T o start the air conditioner Press the ON/OFF operation b utton (automatically setting cooling or heating operation).
Special Remar ks • Because this appliance heats a room by utilizing the heat of the outside air (heat pump system), the heating efficiency will f all off when the outdoor temperature is v er y low . If sufficient heat cannot be obtained with this heat pump , use another heating appliance in conjunction with this unit.
Setting the Timer Use this mode to turn off the appliance automatically after the length of time set. Use this mode to turn the appliance off automatically after the same set time e ver y time . Use this mode to star t the appliance automatically after the length of time set.
How to set the OFF timer ( ) (Example) T o stop the air conditioner after 3.5 hours Operation Indication 1. Press the ON/OFF b utton to star t the air conditioner . 2. Press the TIMER SET b utton once to select the mode. 3. Press the b utton until 3.5 is displa yed.
T roub leshooting If your air conditioner does not w or k properly , first check the f ollowing points bef ore requesting ser vice. If it still does not work properly , contact your dealer or a service center . OI-404-02 - 18EG 2 - 18 Tips f or Energy Sa ving A void • Do not bloc k the air intake and outlet of the unit.
Sa ve These Instructions! TM-SH80UG Pr ogrammable W eekly Timer • INSTRUCTION MANU AL 3 3 TM-SH80UG 5/2/01 3:21 PM Page 1.
OI-432-03 - 2EG 3 - 2 Contents P age Product Inf or mation............................................................................................2 Aler t Symbols.....................................................................................
Installation Location • W e recommend that this air conditioner be installed properly b y qualified installation technicians in accor dance with the Installation Instructions pro vided with the unit. • Bef ore installation, check that the voltage of the electric supply in your home or office is the same as the v oltage shown on the nameplate.
OI-432-03 - 4EG 3 - 4 F eatures 1. Interactive operation allows y ou to control three sets of on/off time per day with an accurac y of one minute . It also enables programmed weekly operation. 2. By programming holida ys (such as public holidays and v acations), you can cancel pr ogrammed operation for certain periods.
Names and Functions of Controls Button functions and the display OI-432-03 - 5EG 3 - 5 A: PROGRAM b utton B: D A Y button J: Programmed operation I: Day indicator H: ON/OFF time indicator K: Holiday i.
Proper Operation 1. T urning on T urn on your unit. Operation of the programmab le weekly timer Adjust the time indicator . → Adjust the da y indicator . → Program a w eekly operation. 2. T urn on your air conditioner that has the programmab le weekly timer .
Setting the day (Example) T o set to Wednesda y (We) STEP 1 Adjust the day indicator b y pressing the DA Y button while keeping the SET button pressed. With each press of the D A Y button while k eeping the SET button pressed, the b linking day indicator ( ) mov es from Su to Sa.
5. How to set pr ogram operations Properly set the time and day indicators to the present time and da y . Otherwise you cannot set program oper ations. 1) F or each day of the week, y ou can set up to three sets of program operation. 2) Y ou can set the following prog ram operations: Setting times to turn on and off.
5. How to set pr ogram operations (Continued) STEP 6 Press the PROGRAM b utton to complete the program setting. Press the PROGRAM b utton within 30 seconds after you finish adjusting y our desired ON-times and OFF-times. Abov e steps complete the program setting of operation f or a day (Monda y in the e xample).
6. When setting the program operation err oneously If the ERROR indicator blinks while y ou are setting program operation, take the follo wing steps to correct times you set. 1 While the blinks , the ON-time of the program oper ation that is incorrectly set also blinks.
7. How to duplicate pr ogrammed operation times If you hope to set ON-times and OFF-times that are the same with those f or another day which are alread y programmed, you can duplicate those times. (Example) T o duplicate the programmed oper ation on Monday to T uesda y 1 In the ordinar y indicator mode, press the CHECK b utton.
9. How to change pr ogrammed operation times 1 In the ordinar y indicator mode, press the PR OGRAM button. 2 Press the D A Y button to mo ve the operation reservation indicator ( ) to the da y the programmed operation times of which you w ant to change.
11. How to set holida ys • By using the CANCEL button, you can temporarily cancel per -day programmed operation. 1 Press the CANCEL button. The holida y indicator ( ) star ts blinking. 2 Press the D A Y button to mo ve the holida y indicator ( ) to the day that y ou want to set as a holiday .
Additional Inf or mation 1. P ower failure When the power resumes after a po wer failure , the display sho wn on the above will appear (the colon of the present time indicator “ : ” will blink). T o restart operation 1 T urn on the power (or the circuit breaker) f or the air conditioner .
Save These Instructions! SHA-KC64UG System Controller f or Split System Air Conditioner • INSTR UCTION MANU AL 4 4 SHA-KC64UG 5/2/01 2:30 PM Page 1.
Contents P age Product Inf or mation .......................................................................................... 2 Aler t Symbols ................................................................................................... 2 Installation Location .
Installation Location • W e recommend that this system controller be installed properl y by qualified installation technicians in accor dance with the Installation Instructions pro vided with the system controller .
Ho w to Use the System Controller ■ Functions of buttons OI-432-04 - 4EG 4 - 4 A: ALL/ZONE/GR SELECT b utton Use this button to select one of the f ollowing: ALL: Used f or tur ning all the air conditioners on and off. ZONE: Used f or tur ning all the air conditioners of each zone on and off .
OI-432-04 - 5EG 4 - 5 D: ON button This button is f or tur ning the selected air conditioner on. E: OFF button This button is f or tur ning the selected air conditioner off .
K: CHECK button This button is used only when servicing the air conditioner . Do not use the CHECK button f or normal operation. L: CENTRAL CTRL button Use this button to inhibit individual oper ation by remote controller as f ollows: 1: Individual ON/OFF operation is inhibited.
OI-432-04 - 7EG 4 - 7 A: When the unit is in the heating standby mode , the indicator appears. B: The currently selected operation mode is displa yed. C: The currently selected F AN SPEED , Airflow Direction and SWEEP settings are displa yed. D: This indication appears when the filter needs cleaning.
■ How to start group operation T o star t group operation The flap setting can be perf or med only for units that ha ve no remote controllers. NO TE OI-432-04 - 8EG 4 - 8 P ower T urn the power supply s witch on more than 5 hours before star ting operation.
OI-432-04 - 9EG 4 - 9 ■ How to start collective operation T o star t collectiv e operation (ALL or ZONE) In the ALL or ZONE mode, no flap setting can be perf or med. If necessar y , you should select the GR mode and use the FLAP button NO TE P ower T urn the power supply s witch on 5 hours or more before star ting operation.
4 4 SHA-KC64UG 5/2/01 2:30 PM Page 10.
4 4 SHA-KC64UG 5/2/01 2:30 PM Page 11.
SANY O FISHER COMP ANY A DIVISION OF SANY O NOR TH AMERICA CORPORA TION 21605 Plummer Street Chatsw or th, CA 91311 U.S.A. In Canada SANY O Canada Inc.
An important point after buying a device Sanyo SHA-KC64UG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo SHA-KC64UG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo SHA-KC64UG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo SHA-KC64UG you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo SHA-KC64UG will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo SHA-KC64UG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo SHA-KC64UG.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo SHA-KC64UG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo SHA-KC64UG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
