Instruction/ maintenance manual of the product PLC-XP30 Sanyo
Go to page of 48
Owner's Man ual PLC-XP30 Multimedia Pr ojector MODEL.
2 C AU TI ON : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
3 SAFETY INSTR UCTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
4 COMPLIANCES Federal Comm unication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
5 T ABLE OF CONTENTS FEA TURES AND DESIGN 6 BEFORE OPERA TION 15 COMPUTER MODE 24 VIDEO MODE 32 SETTING 36 APPENDIX 38 PREP ARA TION 7 NAME OF EACH PART OF THE PROJECTOR 7 SETTING-UP THE PROJECTOR 8 C.
6 FEA TURES AND DESIGN This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
.
SETTING-UP THE PR OJECT OR 8 PREP ARA TION This projector uses nominal input voltages of 100-120 V or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single- phase power systems having a grounded neutral conductor.
9 PREP ARA TION POSITIONING THE PR OJECT OR ● This projector is designed to project on a flat projection surface. ● The projector can be focused from 4.6 ’ (1.4m) ~ 47.3 ’ (14.4m). ● Refer to the figure below to adjust the screen size. Screen Size Distance 40 ” 31 ” 4.
10 PREP ARA TION CA UTION IN CARR YING OR TRANSPORTING THE PROJECT OR ● Do not drop or bump the projector, otherwise damages or malfunctions may result. ● When carrying the projector, use a suitable carrying case. ● Do not transport the projector by using a courier or transport service in an unsuitable transport case.
11 ANALOG DIGIT AL COMPUTER IN 1 COMPUTER IN 2 MONIT OR OUT A V IN CONTROL POR T 1 CONTROL POR T 2 R–A UDIO–L S–VIDEO Y/VIDEO Cb/Pb Cr/Pr (MONO) A UDIO 1 A UDIO 2 (STEREO) (STEREO) RGBH V ANALOG.
MONIT OR OUT RESET R/C JA CK R – A UDIO – L VIDEO RGBH V 12 CONNECTING THE PR OJECT OR Connect an external audio amplifier to these jacks. (Refer to P13, 14.) AUDIO OUTPUT JACKS This projector uses a micro processor to control the unit. Occasionally, the micro processor may malfunction and need to be reset.
13 CONNECTING THE PR OJECT OR CONNECTING T O THE VIDEO EQUIPMENT MONITOR OUT A V IN R – AUDIO – L S – VIDEO Y/VIDEO Cb/Pb Cr/Pr (MONO) R – AUDIO – L VIDEO COMPUTER IN 2 CONTROL PORT 2 AUDIO .
14 CONNECTING THE PR OJECT OR ANALOG DIGIT AL COMPUTER IN 1 COMPUTER IN 2 MONITOR OUT AV IN CONTROL PORT 1 CONTROL PORT 2 S – VIDEO Y/ VID EO Cb/Pb Cr/Pr R – A UDIO – L (MONO) A UDIO 1 A UDIO 2 .
15 MODE MENU SELECT NORMAL A UTO IMA GE LENS SHIFT V OLUME FOCUS ZOOM ON-OFF LAMP REPLA CE W ARNING TEMP . LAMP READ Y BEFORE OPERA TION T OP CONTROLS AND INDICA T ORS Used to adjust zoom.
16 V OLUME ON-OFF FOCUS ZOOM VIDEO COMPUTER D.ZOOM MENU MUTE LASER KEYST ONE NO SHO W FREEZE A UTO IMA GE NORMAL P-TIMER LENS SHIFT LOCK BEFORE OPERA TION OPERA TION OF THE REMO TE CONTR OL ON ALL OFF ALL-OFF SWITCH Left Side When using the Remote Control Unit, turn this switch to “ ON.
17 BEFORE OPERA TION To insure safe operation, please observe the following precautions : ● Use (2) AA, UM3 or R06 type alkaline batteries. ● Replace two batteries at the same time. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid.
18 BEFORE OPERA TION HO W T O OPERA TE ON-SCREEN MENU FLO W OF ON-SCREEN MENU Display ON-SCREEN MENU Press MENU button to display the ON-SCREEN MENU (MENU BAR). The red frame is the POINTER. Select the ITEM by pressing SELECT button. The dialog box of the ITEM appears.
19 BEFORE OPERA TION MENU B AR SYSTEM MENU Used to select a computer system. (Refer to P24) IMAGE MENU Used to adjust the computer image. [Fine sync / Total dots / White Balance / Contrast / Brightness / Sharpness] (Refer to P28) PC ADJUST MENU Used to adjust the parameters to match with the input signal format.
20 B ASIC OPERA TION TURNING ON THE PR OJECT OR Connect the projector's AC Power Cord into a wall outlet and turn the MAIN ON / OFF SWITCH to ON. The LAMP indicator lights RED, and the READY indicator lights GREEN. Press the POWER ON-OFF button on the Remote Control Unit or on the Top Control to ON.
21 B ASIC OPERA TION ADJUSTING THE IMA GE The message disappears after 4 seconds. The message disappears after 4 seconds. Zoom Focus ZOOM ADJUSTMENT FOCUS ADJUSTMENT 1 Press the ZOOM ▲ / ▼ button(s) on the Top Control or on the Remote Control Unit.
22 KEYST ONE ADJUSTMENT 1 Press the KEYSTONE ▲ / ▼ button on the Remote Control Unit or select the Keystone on SCREEN MENU. (Refer to page 31, 35.) The message “ Keystone ” is displayed. 2 Correct the Keystone distortion by pressing the KEYSTONE ▲ / ▼ button or the POINT UP/DOWN button(s).
23 B ASIC OPERA TION Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SOUND and press the SELECT button. Another dialog box SOUND MENU will appear. Sound Volume Adjustment Press the VOLUME (+/ – ) button(s) on the Top Control or on the Remote Control Unit to adjust the volume.
24 COMPUTER button COMPUTER MODE SELECTING COMPUTER MODE MENU OPERA TION When selecting the Computer Mode, the Current Mode display appears to show the information of the computer being selected.
25 COMPUTER MODE COMP A TIBLE COMPUTER SPECIFICA TIONS Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 180 MHz of Dot Clock. NOTE : Specifications are subject to change without notice.
26 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector.
27 COMPUTER MODE The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total lines Recalls the parameter data that was previously adjusted. Reset Stores the parameters in the memory. Stored Clears the parameter data previously set.
28 COMPUTER MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box IMAGE MENU will appear. When selecting “ ▼ , ” the custom setting dialog box will appear.
29 COMPUTER MODE The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The “ Standard ” display will be displayed on the screen for a few seconds.
30 COMPUTER MODE PICTURE POSITION ADJUSTMENT The position of the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select POSITION and press the SELECT button.
31 COMPUTER MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button.
32 VIDEO MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. SELECTING VIDEO MODE DIRECT OPERA TION Select VIDEO mode by pressing the MODE button on the Top Control or the VIDEO button on the Remote Control Unit.
33 VIDEO MODE SELECTING COLOR SYSTEM Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box SYSTEM MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear.
34 VIDEO MODE PICTURE IMA GE ADJUSTMENT Each of the keys operates as follow. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box IMAGE MENU will appear.
35 VIDEO MODE The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Standard" display will be displayed on the screen for a few seconds.
On start When this function is “ On, ” the projector is automatically turned on just by switching the MAIN ON / OFF SWITCH on. Note ; Be sure to turn the projector off properly (refer to the section “ TURNING OFF THE PROJECTOR ” on page 20.). If the projector is turned off in the wrong steps, the On Start function does not operate properly.
37 The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function. (Refer to page 40.) Lamp age SELECTING LANGU A GE Press the MENU button and the ON-SCREEN MENU will appear.
38 APPENDIX OPERA TING WIRELESS MOUSE INST ALLA TION The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse operation.
39 APPENDIX MAINTENANCE W ARNING TEMP . INDICA T OR WARNING TEMP. Indicator flashes red when the internal temperature of the projector exceeds the normal temperature. The Indicator stops flashing when the temperature of the projector returns to normal.
40 APPENDIX LAMP REPLA CEMENT When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required. Turn off the projector and disconnect the AC plug.
41 APPENDIX CLEANING THE PR OJECTION LENS Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. When the projector is not in use, replace the lens cover.
42 APPENDIX TR OUBLESHOO TING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 14.
43 This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. APPENDIX W ARNING : High v oltages are used to operate this projector .
44 APPENDIX 1.3" TFT Active Matrix type, 3 panels TECHNICAL SPECIFICA TIONS Multi-media Projector 20.3 lbs (9.2 kg) 12.44" x 6.46" x 18.9" (316mm x 164mm x 480mm) 1024 x 768 dots 2,359,296 (1024 x 768 x 3 panels) PAL, SECAM, NTSC, NTSC4.
45 APPENDIX CONFIGURA TIONS OF THE TERMINALS COMPUTER INPUT-1 TERMINAL (ANALOG) Terminal : HDB15-PIN Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting the Macintosh computer, the MAC Adapter (supplied) is required.
.
.
Printed in Japan Part No. 610 287 0497 (1AA6P1P2355-- MM6A) SANY O Electric Co., Ltd.
An important point after buying a device Sanyo PLC-XP30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo PLC-XP30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo PLC-XP30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo PLC-XP30 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo PLC-XP30 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo PLC-XP30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo PLC-XP30.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo PLC-XP30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo PLC-XP30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
