Instruction/ maintenance manual of the product 1AA6P1P1756 Sanyo
Go to page of 8
Please read all instructions below and install this system properly . Please read "SAFETY PRECA UTIONS" and "IMPOR T ANT SAFETY INSTR UCTIONS" on O WNER'S MANUAL to install and place this system. This system is supplied in 3 packages and the y need to be installed.
1 CHECK CONTENTS IN P A CKA GES This system is supplied in 3 pac kages. Mak e sure all the par ts listed belo w (cabinets, Installation par ts, and accessories) are included in those packages . T op Cabinet : Ref er to the steps 3 to 6 for installation.
2 ASSEMBLE BO TT OM CABINET Remove the 4 Joint Bolts on the Bottom Cabinet. Keep these bolts for later use. They are necessary for joint the Top and Bottom Cabinets. Remove the 2 Cover Plates on the top of the Bottom Cabinet. Keep the Cover Plates for later use.
3 J0INT T OP AND BO TT OM CABINETS Lift the Top Cabinet and put it on the Bottom Cabinet. When setting the Top Cabinet, be sure the frame of the Bottom Cabinet is fitted into the frame of the Top Cabinet completely. Remove the 14 Screws and the Back Cover.
4 SETUP PR OJECTION MIRR OR Remove the 4 Protection Pads inside of the Top Cabinet and remove the 2 Fixing Bands (right and left) of the Projection Mirror. Remove the 8 Screws(A) of the Mirror Arms. Lift the Projection Mirror and raise the Mirror Arms backward.
5 ADJUST PR OJECTION MIRR OR When the figure of the projection image does not match the Projection Screen, adjust the Projection Mirror . If the figure fits the Projection Screen precisely , skip the steps 2, 3 and 4 and replace the Back Cov er . Connect the projector to the AC outlet, and turn the projector on.
6 ASSEMBLE ST ORA GE SP A CES Replace the Back Cover to the Top Cabinet. Turn the Back Cover over, and fix the cover in the reverse to the initial position. Replace Bac k Cover 1 Back Cover Screws (14 pcs) IInsert the Shelves' Pins into appropreate position of the walls of Storage Spaces.
Turn Lock Bolts to the direction indicated on the figure to lock the cabinet on the floor. Make sure that all the Casters are slightly raised from the floor. The tilt of Cabinet can be also adjusted with these Lock Bolts. Loc k the Cabinet 1 CA UTION BE SURE T O LOCK THE CABINET WITH LOCK BOL TS PR OPERL Y .
An important point after buying a device Sanyo 1AA6P1P1756 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo 1AA6P1P1756 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo 1AA6P1P1756 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo 1AA6P1P1756 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo 1AA6P1P1756 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo 1AA6P1P1756, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo 1AA6P1P1756.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo 1AA6P1P1756. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo 1AA6P1P1756 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
